These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

32 files changed, 1595 insertions, 4 deletions

diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
new file mode 100644
index 000000000..7803e77d8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
@@ -0,0 +1,123 @@
+* ARM Generic Interrupt Controller, version 3
+
+AArch64 SMP cores are often associated with a GICv3, providing Private
+Peripheral Interrupts (PPI), Shared Peripheral Interrupts (SPI),
+Software Generated Interrupts (SGI), and Locality-specific Peripheral
+Interrupts (LPI).
+
+Main node required properties:
+
+- compatible : should at least contain  "arm,gic-v3".
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. Must be a single cell with a value of at least 3.
+
+  The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
+  interrupts. Other values are reserved for future use.
+
+  The 2nd cell contains the interrupt number for the interrupt type.
+  SPI interrupts are in the range [0-987]. PPI interrupts are in the
+  range [0-15].
+
+  The 3rd cell is the flags, encoded as follows:
+	bits[3:0] trigger type and level flags.
+		1 = edge triggered
+		4 = level triggered
+
+  Cells 4 and beyond are reserved for future use. When the 1st cell
+  has a value of 0 or 1, cells 4 and beyond act as padding, and may be
+  ignored. It is recommended that padding cells have a value of 0.
+
+- reg : Specifies base physical address(s) and size of the GIC
+  registers, in the following order:
+  - GIC Distributor interface (GICD)
+  - GIC Redistributors (GICR), one range per redistributor region
+  - GIC CPU interface (GICC)
+  - GIC Hypervisor interface (GICH)
+  - GIC Virtual CPU interface (GICV)
+
+  GICC, GICH and GICV are optional.
+
+- interrupts : Interrupt source of the VGIC maintenance interrupt.
+
+Optional
+
+- redistributor-stride : If using padding pages, specifies the stride
+  of consecutive redistributors. Must be a multiple of 64kB.
+
+- #redistributor-regions: The number of independent contiguous regions
+  occupied by the redistributors. Required if more than one such
+  region is present.
+
+Sub-nodes:
+
+GICv3 has one or more Interrupt Translation Services (ITS) that are
+used to route Message Signalled Interrupts (MSI) to the CPUs.
+
+These nodes must have the following properties:
+- compatible : Should at least contain  "arm,gic-v3-its".
+- msi-controller : Boolean property. Identifies the node as an MSI controller
+- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device
+  which will generate the MSI.
+- reg: Specifies the base physical address and size of the ITS
+  registers.
+
+The main GIC node must contain the appropriate #address-cells,
+#size-cells and ranges properties for the reg property of all ITS
+nodes.
+
+Examples:
+
+	gic: interrupt-controller@2cf00000 {
+		compatible = "arm,gic-v3";
+		#interrupt-cells = <3>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		interrupt-controller;
+		reg = <0x0 0x2f000000 0 0x10000>,	// GICD
+		      <0x0 0x2f100000 0 0x200000>,	// GICR
+		      <0x0 0x2c000000 0 0x2000>,	// GICC
+		      <0x0 0x2c010000 0 0x2000>,	// GICH
+		      <0x0 0x2c020000 0 0x2000>;	// GICV
+		interrupts = <1 9 4>;
+
+		gic-its@2c200000 {
+			compatible = "arm,gic-v3-its";
+			msi-controller;
+			#msi-cells = <1>;
+			reg = <0x0 0x2c200000 0 0x200000>;
+		};
+	};
+
+	gic: interrupt-controller@2c010000 {
+		compatible = "arm,gic-v3";
+		#interrupt-cells = <3>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		interrupt-controller;
+		redistributor-stride = <0x0 0x40000>;	// 256kB stride
+		#redistributor-regions = <2>;
+		reg = <0x0 0x2c010000 0 0x10000>,	// GICD
+		      <0x0 0x2d000000 0 0x800000>,	// GICR 1: CPUs 0-31
+		      <0x0 0x2e000000 0 0x800000>;	// GICR 2: CPUs 32-63
+		      <0x0 0x2c040000 0 0x2000>,	// GICC
+		      <0x0 0x2c060000 0 0x2000>,	// GICH
+		      <0x0 0x2c080000 0 0x2000>;	// GICV
+		interrupts = <1 9 4>;
+
+		gic-its@2c200000 {
+			compatible = "arm,gic-v3-its";
+			msi-controller;
+			#msi-cells = <1>;
+			reg = <0x0 0x2c200000 0 0x200000>;
+		};
+
+		gic-its@2c400000 {
+			compatible = "arm,gic-v3-its";
+			msi-controller;
+			#msi-cells = <1>;
+			reg = <0x0 0x2c400000 0 0x200000>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt
new file mode 100644
index 000000000..cc56021eb
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt
@@ -0,0 +1,168 @@
+* ARM Generic Interrupt Controller
+
+ARM SMP cores are often associated with a GIC, providing per processor
+interrupts (PPI), shared processor interrupts (SPI) and software
+generated interrupts (SGI).
+
+Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
+Secondary GICs are cascaded into the upward interrupt controller and do not
+have PPIs or SGIs.
+
+Main node required properties:
+
+- compatible : should be one of:
+	"arm,arm1176jzf-devchip-gic"
+	"arm,arm11mp-gic"
+	"arm,cortex-a15-gic"
+	"arm,cortex-a7-gic"
+	"arm,cortex-a9-gic"
+	"arm,gic-400"
+	"arm,pl390"
+	"brcm,brahma-b15-gic"
+	"qcom,msm-8660-qgic"
+	"qcom,msm-qgic2"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source.  The type shall be a <u32> and the value shall be 3.
+
+  The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
+  interrupts.
+
+  The 2nd cell contains the interrupt number for the interrupt type.
+  SPI interrupts are in the range [0-987].  PPI interrupts are in the
+  range [0-15].
+
+  The 3rd cell is the flags, encoded as follows:
+	bits[3:0] trigger type and level flags.
+		1 = low-to-high edge triggered
+		2 = high-to-low edge triggered (invalid for SPIs)
+		4 = active high level-sensitive
+		8 = active low level-sensitive (invalid for SPIs).
+	bits[15:8] PPI interrupt cpu mask.  Each bit corresponds to each of
+	the 8 possible cpus attached to the GIC.  A bit set to '1' indicated
+	the interrupt is wired to that CPU.  Only valid for PPI interrupts.
+	Also note that the configurability of PPI interrupts is IMPLEMENTATION
+	DEFINED and as such not guaranteed to be present (most SoC available
+	in 2014 seem to ignore the setting of this flag and use the hardware
+	default value).
+
+- reg : Specifies base physical address(s) and size of the GIC registers. The
+  first region is the GIC distributor register base and size. The 2nd region is
+  the GIC cpu interface register base and size.
+
+Optional
+- interrupts	: Interrupt source of the parent interrupt controller on
+  secondary GICs, or VGIC maintenance interrupt on primary GIC (see
+  below).
+
+- cpu-offset	: per-cpu offset within the distributor and cpu interface
+  regions, used when the GIC doesn't have banked registers. The offset is
+  cpu-offset * cpu-nr.
+
+- clocks        : List of phandle and clock-specific pairs, one for each entry
+  in clock-names.
+- clock-names   : List of names for the GIC clock input(s). Valid clock names
+  depend on the GIC variant:
+	"ic_clk" (for "arm,arm11mp-gic")
+	"PERIPHCLKEN" (for "arm,cortex-a15-gic")
+	"PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic")
+	"clk" (for "arm,gic-400")
+	"gclk" (for "arm,pl390")
+
+- power-domains : A phandle and PM domain specifier as defined by bindings of
+		  the power controller specified by phandle, used when the GIC
+		  is part of a Power or Clock Domain.
+
+
+Example:
+
+	intc: interrupt-controller@fff11000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		interrupt-controller;
+		reg = <0xfff11000 0x1000>,
+		      <0xfff10100 0x100>;
+	};
+
+
+* GIC virtualization extensions (VGIC)
+
+For ARM cores that support the virtualization extensions, additional
+properties must be described (they only exist if the GIC is the
+primary interrupt controller).
+
+Required properties:
+
+- reg : Additional regions specifying the base physical address and
+  size of the VGIC registers. The first additional region is the GIC
+  virtual interface control register base and size. The 2nd additional
+  region is the GIC virtual cpu interface register base and size.
+
+- interrupts : VGIC maintenance interrupt.
+
+Example:
+
+	interrupt-controller@2c001000 {
+		compatible = "arm,cortex-a15-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x2c001000 0x1000>,
+		      <0x2c002000 0x1000>,
+		      <0x2c004000 0x2000>,
+		      <0x2c006000 0x2000>;
+		interrupts = <1 9 0xf04>;
+	};
+
+
+* GICv2m extension for MSI/MSI-x support (Optional)
+
+Certain revisions of GIC-400 supports MSI/MSI-x via V2M register frame(s).
+This is enabled by specifying v2m sub-node(s).
+
+Required properties:
+
+- compatible	    : The value here should contain "arm,gic-v2m-frame".
+
+- msi-controller    : Identifies the node as an MSI controller.
+
+- reg		    : GICv2m MSI interface register base and size
+
+Optional properties:
+
+- arm,msi-base-spi  : When the MSI_TYPER register contains an incorrect
+  		      value, this property should contain the SPI base of
+		      the MSI frame, overriding the HW value.
+
+- arm,msi-num-spis  : When the MSI_TYPER register contains an incorrect
+  		      value, this property should contain the number of
+		      SPIs assigned to the frame, overriding the HW value.
+
+Example:
+
+	interrupt-controller@e1101000 {
+		compatible = "arm,gic-400";
+		#interrupt-cells = <3>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		interrupt-controller;
+		interrupts = <1 8 0xf04>;
+		ranges = <0 0 0 0xe1100000 0 0x100000>;
+		reg = <0x0 0xe1110000 0 0x01000>,
+		      <0x0 0xe112f000 0 0x02000>,
+		      <0x0 0xe1140000 0 0x10000>,
+		      <0x0 0xe1160000 0 0x10000>;
+		v2m0: v2m@0x8000 {
+			compatible = "arm,gic-v2m-frame";
+			msi-controller;
+			reg = <0x0 0x80000 0 0x1000>;
+		};
+
+		....
+
+		v2mN: v2m@0x9000 {
+			compatible = "arm,gic-v2m-frame";
+			msi-controller;
+			reg = <0x0 0x90000 0 0x1000>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt
new file mode 100644
index 000000000..c9cf605bb
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt
@@ -0,0 +1,36 @@
+* ARM Versatile FPGA interrupt controller
+
+One or more FPGA IRQ controllers can be synthesized in an ARM reference board
+such as the Integrator or Versatile family. The output of these different
+controllers are OR:ed together and fed to the CPU tile's IRQ input. Each
+instance can handle up to 32 interrupts.
+
+Required properties:
+- compatible: "arm,versatile-fpga-irq"
+- interrupt-controller: Identifies the node as an interrupt controller
+- #interrupt-cells: The number of cells to define the interrupts.  Must be 1
+  as the FPGA IRQ controller has no configuration options for interrupt
+  sources.  The cell is a u32 and defines the interrupt number.
+- reg: The register bank for the FPGA interrupt controller.
+- clear-mask: a u32 number representing the mask written to clear all IRQs
+  on the controller at boot for example.
+- valid-mask: a u32 number representing a bit mask determining which of
+  the interrupts are valid. Unconnected/unused lines are set to 0, and
+  the system till not make it possible for devices to request these
+  interrupts.
+
+Example:
+
+pic: pic@14000000 {
+        compatible = "arm,versatile-fpga-irq";
+        #interrupt-cells = <1>;
+        interrupt-controller;
+        reg = <0x14000000 0x100>;
+        clear-mask = <0xffffffff>;
+        valid-mask = <0x003fffff>;
+};
+
+Optional properties:
+- interrupts: if the FPGA IRQ controller is cascaded, i.e. if its IRQ
+  output is simply connected to the input of another IRQ controller,
+  then the parent IRQ shall be specified in this property.
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,vic.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,vic.txt
new file mode 100644
index 000000000..dd527216c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/arm,vic.txt
@@ -0,0 +1,41 @@
+* ARM Vectored Interrupt Controller
+
+One or more Vectored Interrupt Controllers (VIC's) can be connected in an ARM
+system for interrupt routing.  For multiple controllers they can either be
+nested or have the outputs wire-OR'd together.
+
+Required properties:
+
+- compatible : should be one of
+	"arm,pl190-vic"
+	"arm,pl192-vic"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : The number of cells to define the interrupts.  Must be 1 as
+  the VIC has no configuration options for interrupt sources.  The cell is a u32
+  and defines the interrupt number.
+- reg : The register bank for the VIC.
+
+Optional properties:
+
+- interrupts : Interrupt source for parent controllers if the VIC is nested.
+- valid-mask : A one cell big bit mask of valid interrupt sources. Each bit
+  represents single interrupt source, starting from source 0 at LSb and ending
+  at source 31 at MSb. A bit that is set means that the source is wired and
+  clear means otherwise. If unspecified, defaults to all valid.
+- valid-wakeup-mask : A one cell big bit mask of interrupt sources that can be
+  configured as wake up source for the system. Order of bits is the same as for
+  valid-mask property. A set bit means that this interrupt source can be
+  configured as a wake up source for the system. If unspecied, defaults to all
+  interrupt sources configurable as wake up sources.
+
+Example:
+
+	vic0: interrupt-controller@60000 {
+		compatible = "arm,pl192-vic";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x60000 0x1000>;
+
+		valid-mask = <0xffffff7f>;
+		valid-wakeup-mask = <0x0000ff7f>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt
index f292917fa..0e9f09a6a 100644
--- a/kernel/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt
@@ -2,7 +2,7 @@
 
 Required properties:
 - compatible: Should be "atmel,<chip>-aic"
-  <chip> can be "at91rm9200", "sama5d3" or "sama5d4"
+  <chip> can be "at91rm9200", "sama5d2", "sama5d3" or "sama5d4"
 - interrupt-controller: Identifies the node as an interrupt controller.
 - interrupt-parent: For single AIC system, it is an empty property.
 - #interrupt-cells: The number of cells to define the interrupts. It should be 3.
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/axis,crisv32-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/axis,crisv32-intc.txt
new file mode 100644
index 000000000..e8b123b0a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/axis,crisv32-intc.txt
@@ -0,0 +1,23 @@
+* CRISv32 Interrupt Controller
+
+Interrupt controller for the CRISv32 SoCs.
+
+Main node required properties:
+
+- compatible : should be:
+	"axis,crisv32-intc"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The type shall be a <u32> and the value shall be 1.
+- reg: physical base address and size of the intc registers map.
+
+Example:
+
+	intc: interrupt-controller {
+		compatible = "axis,crisv32-intc";
+		reg = <0xb001c000 0x1000>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
index 7da578d72..2d6c8bb4d 100644
--- a/kernel/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
@@ -5,9 +5,14 @@ The BCM2835 contains a custom top-level interrupt controller, which supports
 controller, or the HW block containing it, is referred to occasionally
 as "armctrl" in the SoC documentation, hence naming of this binding.
 
+The BCM2836 contains the same interrupt controller with the same
+interrupts, but the per-CPU interrupt controller is the root, and an
+interrupt there indicates that the ARMCTRL has an interrupt to handle.
+
 Required properties:
 
-- compatible : should be "brcm,bcm2835-armctrl-ic"
+- compatible : should be "brcm,bcm2835-armctrl-ic" or
+                 "brcm,bcm2836-armctrl-ic"
 - reg : Specifies base physical address and size of the registers.
 - interrupt-controller : Identifies the node as an interrupt controller
 - #interrupt-cells : Specifies the number of cells needed to encode an
@@ -20,6 +25,12 @@ Required properties:
   The 2nd cell contains the interrupt number within the bank. Valid values
   are 0..7 for bank 0, and 0..31 for bank 1.
 
+Additional required properties for brcm,bcm2836-armctrl-ic:
+- interrupt-parent : Specifies the parent interrupt controller when this
+  controller is the second level.
+- interrupts : Specifies the interrupt on the parent for this interrupt
+  controller to handle.
+
 The interrupt sources are as follows:
 
 Bank 0:
@@ -102,9 +113,21 @@ Bank 2:
 
 Example:
 
+/* BCM2835, first level */
 intc: interrupt-controller {
 	compatible = "brcm,bcm2835-armctrl-ic";
 	reg = <0x7e00b200 0x200>;
 	interrupt-controller;
 	#interrupt-cells = <2>;
 };
+
+/* BCM2836, second level */
+intc: interrupt-controller {
+	compatible = "brcm,bcm2836-armctrl-ic";
+	reg = <0x7e00b200 0x200>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	interrupt-parent = <&local_intc>;
+	interrupts = <8>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2836-l1-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2836-l1-intc.txt
new file mode 100644
index 000000000..f320dcd6e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2836-l1-intc.txt
@@ -0,0 +1,37 @@
+BCM2836 per-CPU interrupt controller
+
+The BCM2836 has a per-cpu interrupt controller for the timer, PMU
+events, and SMP IPIs.  One of the CPUs may receive interrupts for the
+peripheral (GPU) events, which chain to the BCM2835-style interrupt
+controller.
+
+Required properties:
+
+- compatible:	 	Should be "brcm,bcm2836-l1-intc"
+- reg:			Specifies base physical address and size of the
+			  registers
+- interrupt-controller:	Identifies the node as an interrupt controller
+- #interrupt-cells:	Specifies the number of cells needed to encode an
+			  interrupt source. The value shall be 1
+
+Please refer to interrupts.txt in this directory for details of the common
+Interrupt Controllers bindings used by client devices.
+
+The interrupt sources are as follows:
+
+0: CNTPSIRQ
+1: CNTPNSIRQ
+2: CNTHPIRQ
+3: CNTVIRQ
+8: GPU_FAST
+9: PMU_FAST
+
+Example:
+
+local_intc: local_intc {
+	compatible = "brcm,bcm2836-l1-intc";
+	reg = <0x40000000 0x100>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	interrupt-parent = <&local_intc>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt
new file mode 100644
index 000000000..80994adab
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt
@@ -0,0 +1,82 @@
+* Meta External Trigger Controller Binding
+
+This binding specifies what properties must be available in the device tree
+representation of a Meta external trigger controller.
+
+Required properties:
+
+    - compatible: Specifies the compatibility list for the interrupt controller.
+      The type shall be <string> and the value shall include "img,meta-intc".
+
+    - num-banks: Specifies the number of interrupt banks (each of which can
+      handle 32 interrupt sources).
+
+    - interrupt-controller: The presence of this property identifies the node
+      as an interrupt controller. No property value shall be defined.
+
+    - #interrupt-cells: Specifies the number of cells needed to encode an
+      interrupt source. The type shall be a <u32> and the value shall be 2.
+
+    - #address-cells: Specifies the number of cells needed to encode an
+      address. The type shall be <u32> and the value shall be 0. As such,
+      'interrupt-map' nodes do not have to specify a parent unit address.
+
+Optional properties:
+
+    - no-mask: The controller doesn't have any mask registers.
+
+* Interrupt Specifier Definition
+
+  Interrupt specifiers consists of 2 cells encoded as follows:
+
+    - <1st-cell>: The interrupt-number that identifies the interrupt source.
+
+    - <2nd-cell>: The Linux interrupt flags containing level-sense information,
+                  encoded as follows:
+                    1 = edge triggered
+                    4 = level-sensitive
+
+* Examples
+
+Example 1:
+
+	/*
+	 * Meta external trigger block
+	 */
+	intc: intc {
+		// This is an interrupt controller node.
+		interrupt-controller;
+
+		// No address cells so that 'interrupt-map' nodes which
+		// reference this interrupt controller node do not need a parent
+		// address specifier.
+		#address-cells = <0>;
+
+		// Two cells to encode interrupt sources.
+		#interrupt-cells = <2>;
+
+		// Number of interrupt banks
+		num-banks = <2>;
+
+		// No HWMASKEXT is available (specify on Chorus2 and Comet ES1)
+		no-mask;
+
+		// Compatible with Meta hardware trigger block.
+		compatible = "img,meta-intc";
+	};
+
+Example 2:
+
+	/*
+	 * An interrupt generating device that is wired to a Meta external
+	 * trigger block.
+	 */
+	uart1: uart@0x02004c00 {
+		// Interrupt source '5' that is level-sensitive.
+		// Note that there are only two cells as specified in the
+		// interrupt parent's '#interrupt-cells' property.
+		interrupts = <5 4 /* level */>;
+
+		// The interrupt controller that this device is wired to.
+		interrupt-parent = <&intc>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt
new file mode 100644
index 000000000..a69118550
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt
@@ -0,0 +1,105 @@
+* ImgTec Powerdown Controller (PDC) Interrupt Controller Binding
+
+This binding specifies what properties must be available in the device tree
+representation of a PDC IRQ controller. This has a number of input interrupt
+lines which can wake the system, and are passed on through output interrupt
+lines.
+
+Required properties:
+
+    - compatible: Specifies the compatibility list for the interrupt controller.
+      The type shall be <string> and the value shall include "img,pdc-intc".
+
+    - reg: Specifies the base PDC physical address(s) and size(s) of the
+      addressable register space. The type shall be <prop-encoded-array>.
+
+    - interrupt-controller: The presence of this property identifies the node
+      as an interrupt controller. No property value shall be defined.
+
+    - #interrupt-cells: Specifies the number of cells needed to encode an
+      interrupt source. The type shall be a <u32> and the value shall be 2.
+
+    - num-perips: Number of waking peripherals.
+
+    - num-syswakes: Number of SysWake inputs.
+
+    - interrupts: List of interrupt specifiers. The first specifier shall be the
+      shared SysWake interrupt, and remaining specifies shall be PDC peripheral
+      interrupts in order.
+
+* Interrupt Specifier Definition
+
+  Interrupt specifiers consists of 2 cells encoded as follows:
+
+    - <1st-cell>: The interrupt-number that identifies the interrupt source.
+                    0-7:  Peripheral interrupts
+                    8-15: SysWake interrupts
+
+    - <2nd-cell>: The level-sense information, encoded using the Linux interrupt
+                  flags as follows (only 4 valid for peripheral interrupts):
+                    0 = none (decided by software)
+                    1 = low-to-high edge triggered
+                    2 = high-to-low edge triggered
+                    3 = both edge triggered
+                    4 = active-high level-sensitive (required for perip irqs)
+                    8 = active-low level-sensitive
+
+* Examples
+
+Example 1:
+
+	/*
+	 * TZ1090 PDC block
+	 */
+	pdc: pdc@0x02006000 {
+		// This is an interrupt controller node.
+		interrupt-controller;
+
+		// Three cells to encode interrupt sources.
+		#interrupt-cells = <2>;
+
+		// Offset address of 0x02006000 and size of 0x1000.
+		reg = <0x02006000 0x1000>;
+
+		// Compatible with Meta hardware trigger block.
+		compatible = "img,pdc-intc";
+
+		// Three peripherals are connected.
+		num-perips = <3>;
+
+		// Four SysWakes are connected.
+		num-syswakes = <4>;
+
+		interrupts = <18 4 /* level */>, /* Syswakes */
+			     <30 4 /* level */>, /* Peripheral 0 (RTC) */
+			     <29 4 /* level */>, /* Peripheral 1 (IR) */
+			     <31 4 /* level */>; /* Peripheral 2 (WDT) */
+	};
+
+Example 2:
+
+	/*
+	 * An SoC peripheral that is wired through the PDC.
+	 */
+	rtc0 {
+		// The interrupt controller that this device is wired to.
+		interrupt-parent = <&pdc>;
+
+		// Interrupt source Peripheral 0
+		interrupts = <0   /* Peripheral 0 (RTC) */
+		              4>  /* IRQ_TYPE_LEVEL_HIGH */
+	};
+
+Example 3:
+
+	/*
+	 * An interrupt generating device that is wired to a SysWake pin.
+	 */
+	touchscreen0 {
+		// The interrupt controller that this device is wired to.
+		interrupt-parent = <&pdc>;
+
+		// Interrupt source SysWake 0 that is active-low level-sensitive
+		interrupts = <8 /* SysWake0 */
+			      8 /* IRQ_TYPE_LEVEL_LOW */>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/ingenic,intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/ingenic,intc.txt
new file mode 100644
index 000000000..5f89fb635
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/ingenic,intc.txt
@@ -0,0 +1,28 @@
+Ingenic SoC Interrupt Controller
+
+Required properties:
+
+- compatible : should be "ingenic,<socname>-intc". Valid strings are:
+    ingenic,jz4740-intc
+    ingenic,jz4770-intc
+    ingenic,jz4775-intc
+    ingenic,jz4780-intc
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 1.
+- interrupt-parent : phandle of the CPU interrupt controller.
+- interrupts : Specifies the CPU interrupt the controller is connected to.
+
+Example:
+
+intc: interrupt-controller@10001000 {
+	compatible = "ingenic,jz4740-intc";
+	reg = <0x10001000 0x14>;
+
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	interrupt-parent = <&cpuintc>;
+	interrupts = <2>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/intel,ce4100-ioapic.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/intel,ce4100-ioapic.txt
new file mode 100644
index 000000000..7d19f494f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/intel,ce4100-ioapic.txt
@@ -0,0 +1,26 @@
+Interrupt chips
+---------------
+
+* Intel I/O Advanced Programmable Interrupt Controller (IO APIC)
+
+  Required properties:
+  --------------------
+     compatible = "intel,ce4100-ioapic";
+     #interrupt-cells = <2>;
+
+  Device's interrupt property:
+
+     interrupts = <P S>;
+
+  The first number (P) represents the interrupt pin which is wired to the
+  IO APIC. The second number (S) represents the sense of interrupt which
+  should be configured and can be one of:
+    0 - Edge Rising
+    1 - Level Low
+    2 - Level High
+    3 - Edge Falling
+
+* Local APIC
+  Required property:
+
+     compatible = "intel,ce4100-lapic";
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
new file mode 100644
index 000000000..afef6a85a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -0,0 +1,32 @@
++Mediatek 65xx/67xx/81xx sysirq
+
+Mediatek SOCs sysirq support controllable irq inverter for each GIC SPI
+interrupt.
+
+Required properties:
+- compatible: should be one of:
+	"mediatek,mt8173-sysirq"
+	"mediatek,mt8135-sysirq"
+	"mediatek,mt8127-sysirq"
+	"mediatek,mt6795-sysirq"
+	"mediatek,mt6592-sysirq"
+	"mediatek,mt6589-sysirq"
+	"mediatek,mt6582-sysirq"
+	"mediatek,mt6580-sysirq"
+	"mediatek,mt6577-sysirq"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Use the same format as specified by GIC in
+  Documentation/devicetree/bindings/arm/gic.txt
+- interrupt-parent: phandle of irq parent for sysirq. The parent must
+  use the same interrupt-cells format as GIC.
+- reg: Physical base address of the intpol registers and length of memory
+  mapped region.
+
+Example:
+	sysirq: interrupt-controller@10200100 {
+		compatible = "mediatek,mt6589-sysirq", "mediatek,mt6577-sysirq";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		interrupt-parent = <&gic>;
+		reg = <0 0x10200100 0 0x1c>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/mrvl,intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/mrvl,intc.txt
new file mode 100644
index 000000000..8b53273cb
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/mrvl,intc.txt
@@ -0,0 +1,60 @@
+* Marvell MMP Interrupt controller
+
+Required properties:
+- compatible : Should be "mrvl,mmp-intc", "mrvl,mmp2-intc" or
+  "mrvl,mmp2-mux-intc"
+- reg : Address and length of the register set of the interrupt controller.
+  If the interrupt controller is intc, address and length means the range
+  of the whold interrupt controller. If the interrupt controller is mux-intc,
+  address and length means one register. Since address of mux-intc is in the
+  range of intc. mux-intc is secondary interrupt controller.
+- reg-names : Name of the register set of the interrupt controller. It's
+  only required in mux-intc interrupt controller.
+- interrupts : Should be the port interrupt shared by mux interrupts. It's
+  only required in mux-intc interrupt controller.
+- interrupt-controller : Identifies the node as an interrupt controller.
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source.
+- mrvl,intc-nr-irqs : Specifies the number of interrupts in the interrupt
+  controller.
+- mrvl,clr-mfp-irq : Specifies the interrupt that needs to clear MFP edge
+  detection first.
+
+Example:
+	intc: interrupt-controller@d4282000 {
+		compatible = "mrvl,mmp2-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0xd4282000 0x1000>;
+		mrvl,intc-nr-irqs = <64>;
+	};
+
+	intcmux4@d4282150 {
+		compatible = "mrvl,mmp2-mux-intc";
+		interrupts = <4>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x150 0x4>, <0x168 0x4>;
+		reg-names = "mux status", "mux mask";
+		mrvl,intc-nr-irqs = <2>;
+	};
+
+* Marvell Orion Interrupt controller
+
+Required properties
+- compatible :  Should be "marvell,orion-intc".
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source. Supported value is <1>.
+- interrupt-controller : Declare this node to be an interrupt controller.
+- reg : Interrupt mask address. A list of 4 byte ranges, one per controller.
+        One entry in the list represents 32 interrupts.
+
+Example:
+
+	intc: interrupt-controller {
+        	compatible = "marvell,orion-intc", "marvell,intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+                reg = <0xfed20204 0x04>,
+		      <0xfed20214 0x04>;
+        };
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/msi.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/msi.txt
new file mode 100644
index 000000000..c60c034dc
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/msi.txt
@@ -0,0 +1,135 @@
+This document describes the generic device tree binding for MSI controllers and
+their master(s).
+
+Message Signaled Interrupts (MSIs) are a class of interrupts generated by a
+write to an MMIO address.
+
+MSIs were originally specified by PCI (and are used with PCIe), but may also be
+used with other busses, and hence a mechanism is required to relate devices on
+those busses to the MSI controllers which they are capable of using,
+potentially including additional information.
+
+MSIs are distinguished by some combination of:
+
+- The doorbell (the MMIO address written to).
+  
+  Devices may be configured by software to write to arbitrary doorbells which
+  they can address. An MSI controller may feature a number of doorbells.
+
+- The payload (the value written to the doorbell).
+  
+  Devices may be configured to write an arbitrary payload chosen by software.
+  MSI controllers may have restrictions on permitted payloads.
+
+- Sideband information accompanying the write.
+  
+  Typically this is neither configurable nor probeable, and depends on the path
+  taken through the memory system (i.e. it is a property of the combination of
+  MSI controller and device rather than a property of either in isolation).
+
+
+MSI controllers:
+================
+
+An MSI controller signals interrupts to a CPU when a write is made to an MMIO
+address by some master. An MSI controller may feature a number of doorbells.
+
+Required properties:
+--------------------
+
+- msi-controller: Identifies the node as an MSI controller.
+
+Optional properties:
+--------------------
+
+- #msi-cells: The number of cells in an msi-specifier, required if not zero.
+
+  Typically this will encode information related to sideband data, and will
+  not encode doorbells or payloads as these can be configured dynamically.
+
+  The meaning of the msi-specifier is defined by the device tree binding of
+  the specific MSI controller. 
+
+
+MSI clients
+===========
+
+MSI clients are devices which generate MSIs. For each MSI they wish to
+generate, the doorbell and payload may be configured, though sideband
+information may not be configurable.
+
+Required properties:
+--------------------
+
+- msi-parent: A list of phandle + msi-specifier pairs, one for each MSI
+  controller which the device is capable of using.
+
+  This property is unordered, and MSIs may be allocated from any combination of
+  MSI controllers listed in the msi-parent property.
+
+  If a device has restrictions on the allocation of MSIs, these restrictions
+  must be described with additional properties.
+
+  When #msi-cells is non-zero, busses with an msi-parent will require
+  additional properties to describe the relationship between devices on the bus
+  and the set of MSIs they can potentially generate.
+
+
+Example
+=======
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	msi_a: msi-controller@a {
+		reg = <0xa 0xf00>;
+		compatible = "vendor-a,some-controller";
+		msi-controller;
+		/* No sideband data, so #msi-cells omitted */
+	};
+
+	msi_b: msi-controller@b {
+		reg = <0xb 0xf00>;
+		compatible = "vendor-b,another-controller";
+		msi-controller;
+		/* Each device has some unique ID */
+		#msi-cells = <1>;
+	};
+
+	msi_c: msi-controller@c {
+		reg = <0xb 0xf00>;
+		compatible = "vendor-b,another-controller";
+		msi-controller;
+		/* Each device has some unique ID */
+		#msi-cells = <1>;
+	};
+
+	dev@0 {
+		reg = <0x0 0xf00>;
+		compatible = "vendor-c,some-device";
+
+		/* Can only generate MSIs to msi_a */
+		msi-parent = <&msi_a>;
+	};
+
+	dev@1 {
+		reg = <0x1 0xf00>;
+		compatible = "vendor-c,some-device";
+
+		/* 
+		 * Can generate MSIs to either A or B.
+		 */
+		msi-parent = <&msi_a>, <&msi_b 0x17>;
+	};
+
+	dev@2 {
+		reg = <0x2 0xf00>;
+		compatible = "vendor-c,some-device";
+		/*
+		 * Has different IDs at each MSI controller.
+		 * Can generate MSIs to all of the MSI controllers.
+		 */
+		msi-parent = <&msi_a>, <&msi_b 0x17>, <&msi_c 0x53>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt
new file mode 100644
index 000000000..539adca19
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt
@@ -0,0 +1,38 @@
+* NXP LPC32xx Main Interrupt Controller
+  (MIC, including SIC1 and SIC2 secondary controllers)
+
+Required properties:
+- compatible: Should be "nxp,lpc3220-mic"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- interrupt-parent: Empty for the interrupt controller itself
+- #interrupt-cells: The number of cells to define the interrupts. Should be 2.
+  The first cell is the IRQ number
+  The second cell is used to specify mode:
+      1 = low-to-high edge triggered
+      2 = high-to-low edge triggered
+      4 = active high level-sensitive
+      8 = active low level-sensitive
+      Default for internal sources should be set to 4 (active high).
+- reg: Should contain MIC registers location and length
+
+Examples:
+	/*
+	 * MIC
+	 */
+	mic: interrupt-controller@40008000 {
+		compatible = "nxp,lpc3220-mic";
+		interrupt-controller;
+		interrupt-parent;
+		#interrupt-cells = <2>;
+		reg = <0x40008000 0xC000>;
+	};
+
+	/*
+	 * ADC
+	 */
+	adc@40048000 {
+		compatible = "nxp,lpc3220-adc";
+		reg = <0x40048000 0x1000>;
+		interrupt-parent = <&mic>;
+		interrupts = <39 4>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/open-pic.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/open-pic.txt
new file mode 100644
index 000000000..909a902df
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/open-pic.txt
@@ -0,0 +1,98 @@
+* Open PIC Binding
+
+This binding specifies what properties must be available in the device tree
+representation of an Open PIC compliant interrupt controller.  This binding is
+based on the binding defined for Open PIC in [1] and is a superset of that
+binding.
+
+Required properties:
+
+  NOTE: Many of these descriptions were paraphrased here from [1] to aid
+        readability.
+
+    - compatible: Specifies the compatibility list for the PIC.  The type
+      shall be <string> and the value shall include "open-pic".
+
+    - reg: Specifies the base physical address(s) and size(s) of this
+      PIC's addressable register space.  The type shall be <prop-encoded-array>.
+
+    - interrupt-controller: The presence of this property identifies the node
+      as an Open PIC.  No property value shall be defined.
+
+    - #interrupt-cells: Specifies the number of cells needed to encode an
+      interrupt source.  The type shall be a <u32> and the value shall be 2.
+
+    - #address-cells: Specifies the number of cells needed to encode an
+      address.  The type shall be <u32> and the value shall be 0.  As such,
+      'interrupt-map' nodes do not have to specify a parent unit address.
+
+Optional properties:
+
+    - pic-no-reset: The presence of this property indicates that the PIC
+      shall not be reset during runtime initialization.  No property value shall
+      be defined.  The presence of this property also mandates that any
+      initialization related to interrupt sources shall be limited to sources
+      explicitly referenced in the device tree.
+
+* Interrupt Specifier Definition
+
+  Interrupt specifiers consists of 2 cells encoded as
+  follows:
+
+    - <1st-cell>: The interrupt-number that identifies the interrupt source.
+
+    - <2nd-cell>: The level-sense information, encoded as follows:
+                    0 = low-to-high edge triggered
+                    1 = active low level-sensitive
+                    2 = active high level-sensitive
+                    3 = high-to-low edge triggered
+
+* Examples
+
+Example 1:
+
+	/*
+	 * An Open PIC interrupt controller
+	 */
+	mpic: pic@40000 {
+		// This is an interrupt controller node.
+		interrupt-controller;
+
+		// No address cells so that 'interrupt-map' nodes which reference
+		// this Open PIC node do not need a parent address specifier.
+		#address-cells = <0>;
+
+		// Two cells to encode interrupt sources.
+		#interrupt-cells = <2>;
+
+		// Offset address of 0x40000 and size of 0x40000.
+		reg = <0x40000 0x40000>;
+
+		// Compatible with Open PIC.
+		compatible = "open-pic";
+
+		// The PIC shall not be reset.
+		pic-no-reset;
+	};
+
+Example 2:
+
+	/*
+	 * An interrupt generating device that is wired to an Open PIC.
+	 */
+	serial0: serial@4500 {
+		// Interrupt source '42' that is active high level-sensitive.
+		// Note that there are only two cells as specified in the interrupt
+		// parent's '#interrupt-cells' property.
+		interrupts = <42 2>;
+
+		// The interrupt controller that this device is wired to.
+		interrupt-parent = <&mpic>;
+	};
+
+* References
+
+[1] Power.org (TM) Standard for Embedded Power Architecture (TM) Platform
+    Requirements (ePAPR), Version 1.0, July 2008.
+    (http://www.power.org/resources/downloads/Power_ePAPR_APPROVED_v1.0.pdf)
+
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-cpu-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-cpu-intc.txt
new file mode 100644
index 000000000..aabce7810
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-cpu-intc.txt
@@ -0,0 +1,44 @@
+Binding for Qualcomm Atheros AR7xxx/AR9XXX CPU interrupt controller
+
+On most SoC the IRQ controller need to flush the DDR FIFO before running
+the interrupt handler of some devices. This is configured using the
+qca,ddr-wb-channels and qca,ddr-wb-channel-interrupts properties.
+
+Required Properties:
+
+- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-cpu-intc"
+  as fallback
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode interrupt
+		     source, should be 1 for intc
+
+Please refer to interrupts.txt in this directory for details of the common
+Interrupt Controllers bindings used by client devices.
+
+Optional Properties:
+
+- qca,ddr-wb-channel-interrupts: List of the interrupts needing a write
+  buffer flush
+- qca,ddr-wb-channels: List of phandles to the write buffer channels for
+  each interrupt. If qca,ddr-wb-channel-interrupts is not present the interrupt
+  default to the entry's index.
+
+Example:
+
+	interrupt-controller {
+		compatible = "qca,ar9132-cpu-intc", "qca,ar7100-cpu-intc";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>;
+		qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>,
+					<&ddr_ctrl 0>, <&ddr_ctrl 1>;
+	};
+
+	...
+
+	ddr_ctrl: memory-controller@18000000 {
+		...
+		#qca,ddr-wb-channel-cells = <1>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt
new file mode 100644
index 000000000..ec96b1f01
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt
@@ -0,0 +1,46 @@
+Binding for Qualcomm Atheros AR7xxx/AR9XXX MISC interrupt controller
+
+The MISC interrupt controller is a secondary controller for lower priority
+interrupt.
+
+Required Properties:
+- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" or
+  "qca,<soctype>-cpu-intc", "qca,ar7240-misc-intc"
+- reg: Base address and size of the controllers memory area
+- interrupt-parent: phandle of the parent interrupt controller.
+- interrupts: Interrupt specifier for the controllers interrupt.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode interrupt
+		     source, should be 1
+
+Compatible fallback depends on the SoC. Use ar7100 for ar71xx and ar913x,
+use ar7240 for all other SoCs.
+
+Please refer to interrupts.txt in this directory for details of the common
+Interrupt Controllers bindings used by client devices.
+
+Example:
+
+	interrupt-controller@18060010 {
+		compatible = "qca,ar9132-misc-intc", qca,ar7100-misc-intc";
+		reg = <0x18060010 0x4>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <6>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+Another example:
+
+	interrupt-controller@18060010 {
+		compatible = "qca,ar9331-misc-intc", qca,ar7240-misc-intc";
+		reg = <0x18060010 0x4>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <6>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,h8300h-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,h8300h-intc.txt
new file mode 100644
index 000000000..56e8d82af
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,h8300h-intc.txt
@@ -0,0 +1,22 @@
+* H8/300H Interrupt controller
+
+Required properties:
+
+- compatible: has to be "renesas,h8300h-intc", "renesas,h8300-intc" as fallback.
+- #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in
+  interrupts.txt in this directory
+- regs: Base address of interrupt controller registers.
+
+Optional properties:
+
+- any properties, listed in interrupts.txt, and any standard resource allocation
+  properties
+
+Example:
+
+	h8intc: interrupt-controller@fee012 {
+		compatible = "renesas,h8300h-intc", "renesas,h8300-intc";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <0xfee012 7>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,h8s-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,h8s-intc.txt
new file mode 100644
index 000000000..faded2b15
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,h8s-intc.txt
@@ -0,0 +1,22 @@
+* H8S Interrupt controller
+
+Required properties:
+
+- compatible: has to be "renesas,h8s-intc", "renesas,h8300-intc" as fallback.
+- #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in
+  interrupts.txt in this directory
+- regs: Base address of interrupt controller registers.
+
+Optional properties:
+
+- any properties, listed in interrupts.txt, and any standard resource allocation
+  properties
+
+Example:
+
+	h8intc: interrupt-controller@fffe00 {
+		compatible = "renesas,h8s-intc", "renesas,h8300-intc";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <0xfffe00 24>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt
index 4f7946ae8..772c550d3 100644
--- a/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt
@@ -13,9 +13,12 @@ Required properties:
 - reg: Base address and length of each register bank used by the external
   IRQ pins driven by the interrupt controller hardware module. The base
   addresses, length and number of required register banks varies with soctype.
-
+- interrupt-controller: Identifies the node as an interrupt controller.
 - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in
-  interrupts.txt in this directory
+  interrupts.txt in this directory.
+- interrupts: Must contain a list of interrupt specifiers. For each interrupt
+  provided by this irqpin controller instance, there must be one entry,
+  referring to the corresponding parent interrupt.
 
 Optional properties:
 
@@ -25,3 +28,35 @@ Optional properties:
   if different from the default 4 bits
 - control-parent: disable and enable interrupts on the parent interrupt
   controller, needed for some broken implementations
+- clocks: Must contain a reference to the functional clock.  This property is
+  mandatory if the hardware implements a controllable functional clock for
+  the irqpin controller instance.
+- power-domains: Must contain a reference to the power domain. This property is
+  mandatory if the irqpin controller instance is part of a controllable power
+  domain.
+
+
+Example
+-------
+
+	irqpin1: interrupt-controller@e6900004 {
+		compatible = "renesas,intc-irqpin-r8a7740",
+			     "renesas,intc-irqpin";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <0xe6900004 4>,
+			<0xe6900014 4>,
+			<0xe6900024 1>,
+			<0xe6900044 1>,
+			<0xe6900064 1>;
+		interrupts = <0 149 IRQ_TYPE_LEVEL_HIGH
+			      0 149 IRQ_TYPE_LEVEL_HIGH
+			      0 149 IRQ_TYPE_LEVEL_HIGH
+			      0 149 IRQ_TYPE_LEVEL_HIGH
+			      0 149 IRQ_TYPE_LEVEL_HIGH
+			      0 149 IRQ_TYPE_LEVEL_HIGH
+			      0 149 IRQ_TYPE_LEVEL_HIGH
+			      0 149 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp2_clks R8A7740_CLK_INTCA>;
+		power-domains = <&pd_a4s>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt
index 63633bdea..ae5054c27 100644
--- a/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt
@@ -10,6 +10,7 @@ Required properties:
     - "renesas,irqc-r8a7792" (R-Car V2H)
     - "renesas,irqc-r8a7793" (R-Car M2-N)
     - "renesas,irqc-r8a7794" (R-Car E2)
+    - "renesas,intc-ex-r8a7795" (R-Car H3)
 - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in
   interrupts.txt in this directory
 - clocks: Must contain a reference to the functional clock.
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/samsung,exynos4210-combiner.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/samsung,exynos4210-combiner.txt
new file mode 100644
index 000000000..9e5f73412
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/samsung,exynos4210-combiner.txt
@@ -0,0 +1,52 @@
+* Samsung Exynos Interrupt Combiner Controller
+
+Samsung's Exynos4 architecture includes a interrupt combiner controller which
+can combine interrupt sources as a group and provide a single interrupt request
+for the group. The interrupt request from each group are connected to a parent
+interrupt controller, such as GIC in case of Exynos4210.
+
+The interrupt combiner controller consists of multiple combiners. Up to eight
+interrupt sources can be connected to a combiner. The combiner outputs one
+combined interrupt for its eight interrupt sources. The combined interrupt
+is usually connected to a parent interrupt controller.
+
+A single node in the device tree is used to describe the interrupt combiner
+controller module (which includes multiple combiners). A combiner in the
+interrupt controller module shares config/control registers with other
+combiners. For example, a 32-bit interrupt enable/disable config register
+can accommodate up to 4 interrupt combiners (with each combiner supporting
+up to 8 interrupt sources).
+
+Required properties:
+- compatible: should be "samsung,exynos4210-combiner".
+- interrupt-controller: Identifies the node as an interrupt controller.
+- #interrupt-cells: should be <2>. The meaning of the cells are
+	* First Cell: Combiner Group Number.
+	* Second Cell: Interrupt number within the group.
+- reg: Base address and size of interrupt combiner registers.
+- interrupts: The list of interrupts generated by the combiners which are then
+    connected to a parent interrupt controller. The format of the interrupt
+    specifier depends in the interrupt parent controller.
+
+Optional properties:
+- samsung,combiner-nr: The number of interrupt combiners supported. If this
+  property is not specified, the default number of combiners is assumed
+  to be 16.
+- interrupt-parent: pHandle of the parent interrupt controller, if not
+  inherited from the parent node.
+
+
+Example:
+
+	The following is a an example from the Exynos4210 SoC dtsi file.
+
+	combiner:interrupt-controller@10440000 {
+		compatible = "samsung,exynos4210-combiner";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <0x10440000 0x1000>;
+		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,arc700-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,arc700-intc.txt
new file mode 100644
index 000000000..9a5d56243
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,arc700-intc.txt
@@ -0,0 +1,24 @@
+* ARC700 incore Interrupt Controller
+
+  The core interrupt controller provides 32 prioritised interrupts (2 levels)
+  to ARC700 core.
+
+Properties:
+
+- compatible: "snps,arc700-intc"
+- interrupt-controller: This is an interrupt controller.
+- #interrupt-cells: Must be <1>.
+
+  Single Cell "interrupts" property of a device specifies the IRQ number
+  between 0 to 31
+
+  intc accessed via the special ARC AUX register interface, hence "reg" property
+  is not specified.
+
+Example:
+
+	intc: interrupt-controller {
+		compatible = "snps,arc700-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt
new file mode 100644
index 000000000..0dcb7c7d3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt
@@ -0,0 +1,46 @@
+* ARC-HS Interrupt Distribution Unit
+
+  This optional 2nd level interrupt controller can be used in SMP configurations for
+  dynamic IRQ routing, load balancing of common/external IRQs towards core intc.
+
+Properties:
+
+- compatible: "snps,archs-idu-intc"
+- interrupt-controller: This is an interrupt controller.
+- interrupt-parent: <reference to parent core intc>
+- #interrupt-cells: Must be <2>.
+- interrupts: <...> specifies the upstream core irqs
+
+  First cell specifies the "common" IRQ from peripheral to IDU
+  Second cell specifies the irq distribution mode to cores
+     0=Round Robin; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3
+
+  intc accessed via the special ARC AUX register interface, hence "reg" property
+  is not specified.
+
+Example:
+	core_intc: core-interrupt-controller {
+		compatible = "snps,archs-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	idu_intc: idu-interrupt-controller {
+		compatible = "snps,archs-idu-intc";
+		interrupt-controller;
+		interrupt-parent = <&core_intc>;
+
+		/*
+		 * <hwirq  distribution>
+		 * distribution: 0=RR; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3
+		 */
+		#interrupt-cells = <2>;
+
+		/* upstream core irqs: downstream these are "COMMON" irq 0,1..  */
+		interrupts = <24 25 26 27 28 29 30 31>;
+	};
+
+	some_device: serial@c0fc1000 {
+		interrupt-parent = <&idu_intc>;
+		interrupts = <0 0>;	/* upstream idu IRQ #24, Round Robin */
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,archs-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,archs-intc.txt
new file mode 100644
index 000000000..69f326d6a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/snps,archs-intc.txt
@@ -0,0 +1,22 @@
+* ARC-HS incore Interrupt Controller (Provided by cores implementing ARCv2 ISA)
+
+Properties:
+
+- compatible: "snps,archs-intc"
+- interrupt-controller: This is an interrupt controller.
+- #interrupt-cells: Must be <1>.
+
+  Single Cell "interrupts" property of a device specifies the IRQ number
+  between 16 to 256
+
+  intc accessed via the special ARC AUX register interface, hence "reg" property
+  is not specified.
+
+Example:
+
+	intc: interrupt-controller {
+		compatible = "snps,archs-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupts = <16 17 18 19 20 21 22 23 24 25>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt
new file mode 100644
index 000000000..715a013ed
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt
@@ -0,0 +1,48 @@
+* SPEAr Shared IRQ layer (shirq)
+
+SPEAr3xx architecture includes shared/multiplexed irqs for certain set
+of devices. The multiplexor provides a single interrupt to parent
+interrupt controller (VIC) on behalf of a group of devices.
+
+There can be multiple groups available on SPEAr3xx variants but not
+exceeding 4. The number of devices in a group can differ, further they
+may share same set of status/mask registers spanning across different
+bit masks. Also in some cases the group may not have enable or other
+registers. This makes software little complex.
+
+A single node in the device tree is used to describe the shared
+interrupt multiplexor (one node for all groups). A group in the
+interrupt controller shares config/control registers with other groups.
+For example, a 32-bit interrupt enable/disable config register can
+accommodate up to 4 interrupt groups.
+
+Required properties:
+  - compatible: should be, either of
+     - "st,spear300-shirq"
+     - "st,spear310-shirq"
+     - "st,spear320-shirq"
+  - interrupt-controller: Identifies the node as an interrupt controller.
+  - #interrupt-cells: should be <1> which basically contains the offset
+    (starting from 0) of interrupts for all the groups.
+  - reg: Base address and size of shirq registers.
+  - interrupts: The list of interrupts generated by the groups which are
+    then connected to a parent interrupt controller. Each group is
+    associated with one of the interrupts, hence number of interrupts (to
+    parent) is equal to number of groups. The format of the interrupt
+    specifier depends in the interrupt parent controller.
+
+  Optional properties:
+  - interrupt-parent: pHandle of the parent interrupt controller, if not
+    inherited from the parent node.
+
+Example:
+
+The following is an example from the SPEAr320 SoC dtsi file.
+
+shirq: interrupt-controller@0xb3000000 {
+	compatible = "st,spear320-shirq";
+	reg = <0xb3000000 0x1000>;
+	interrupts = <28 29 30 1>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
+};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,c64x+megamod-pic.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,c64x+megamod-pic.txt
new file mode 100644
index 000000000..42bb796cc
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,c64x+megamod-pic.txt
@@ -0,0 +1,104 @@
+C6X Interrupt Chips
+-------------------
+
+* C64X+ Core Interrupt Controller
+
+  The core interrupt controller provides 16 prioritized interrupts to the
+  C64X+ core. Priority 0 and 1 are used for reset and NMI respectively.
+  Priority 2 and 3 are reserved. Priority 4-15 are used for interrupt
+  sources coming from outside the core.
+
+  Required properties:
+  --------------------
+  - compatible: Should be "ti,c64x+core-pic";
+  - #interrupt-cells: <1>
+
+  Interrupt Specifier Definition
+  ------------------------------
+  Single cell specifying the core interrupt priority level (4-15) where
+  4 is highest priority and 15 is lowest priority.
+
+  Example
+  -------
+  core_pic: interrupt-controller@0 {
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	compatible = "ti,c64x+core-pic";
+  };
+
+
+
+* C64x+ Megamodule Interrupt Controller
+
+  The megamodule PIC consists of four interrupt mupliplexers each of which
+  combine up to 32 interrupt inputs into a single interrupt output which
+  may be cascaded into the core interrupt controller. The megamodule PIC
+  has a total of 12 outputs cascading into the core interrupt controller.
+  One for each core interrupt priority level. In addition to the combined
+  interrupt sources, individual megamodule interrupts may be cascaded to
+  the core interrupt controller. When an individual interrupt is cascaded,
+  it is no longer handled through a megamodule interrupt combiner and is
+  considered to have the core interrupt controller as the parent.
+
+  Required properties:
+  --------------------
+  - compatible: "ti,c64x+megamod-pic"
+  - interrupt-controller
+  - #interrupt-cells: <1>
+  - reg: base address and size of register area
+  - interrupt-parent: must be core interrupt controller
+  - interrupts: This should have four cells; one for each interrupt combiner.
+                The cells contain the core priority interrupt to which the
+                corresponding combiner output is wired.
+
+  Optional properties:
+  --------------------
+  - ti,c64x+megamod-pic-mux: Array of 12 cells correspnding to the 12 core
+                             priority interrupts. The first cell corresponds to
+                             core priority 4 and the last cell corresponds to
+                             core priority 15. The value of each cell is the
+                             megamodule interrupt source which is MUXed to
+                             the core interrupt corresponding to the cell
+                             position. Allowed values are 4 - 127. Mapping for
+                             interrupts 0 - 3 (combined interrupt sources) are
+                             ignored.
+
+  Interrupt Specifier Definition
+  ------------------------------
+  Single cell specifying the megamodule interrupt source (4-127). Note that
+  interrupts mapped directly to the core with "ti,c64x+megamod-pic-mux" will
+  use the core interrupt controller as their parent and the specifier will
+  be the core priority level, not the megamodule interrupt number.
+
+  Examples
+  --------
+  megamod_pic: interrupt-controller@1800000 {
+	compatible = "ti,c64x+megamod-pic";
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	reg = <0x1800000 0x1000>;
+	interrupt-parent = <&core_pic>;
+	interrupts = < 12 13 14 15 >;
+  };
+
+  This is a minimal example where all individual interrupts go through a
+  combiner. Combiner-0 is mapped to core interrupt 12, combiner-1 is mapped
+  to interrupt 13, etc.
+
+
+  megamod_pic: interrupt-controller@1800000 {
+	compatible = "ti,c64x+megamod-pic";
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	reg = <0x1800000 0x1000>;
+	interrupt-parent = <&core_pic>;
+	interrupts = < 12 13 14 15 >;
+	ti,c64x+megamod-pic-mux = <  0  0  0  0
+                                    32  0  0  0
+                                     0  0  0  0 >;
+  };
+
+  This the same as the first example except that megamodule interrupt 32 is
+  mapped directly to core priority interrupt 8. The node using this interrupt
+  must set the core controller as its interrupt parent and use 8 in the
+  interrupt specifier value.
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,cp-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,cp-intc.txt
new file mode 100644
index 000000000..597e8a089
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,cp-intc.txt
@@ -0,0 +1,27 @@
+* TI Common Platform Interrupt Controller
+
+Common Platform Interrupt Controller (cp_intc) is used on
+OMAP-L1x SoCs and can support several configurable number
+of interrupts.
+
+Main node required properties:
+
+- compatible : should be:
+	"ti,cp-intc"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The type shall be a <u32> and the value shall be 1.
+
+  The cell contains the interrupt number in the range [0-128].
+- ti,intc-size: Number of interrupts handled by the interrupt controller.
+- reg: physical base address and size of the intc registers map.
+
+Example:
+
+	intc: interrupt-controller@1 {
+		compatible = "ti,cp-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		ti,intc-size = <101>;
+		reg = <0xfffee000 0x2000>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,omap2-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,omap2-intc.txt
new file mode 100644
index 000000000..f2583e6ec
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/ti,omap2-intc.txt
@@ -0,0 +1,27 @@
+* OMAP Interrupt Controller
+
+OMAP2/3 are using a TI interrupt controller that can support several
+configurable number of interrupts.
+
+Main node required properties:
+
+- compatible : should be:
+	"ti,omap2-intc"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The type shall be a <u32> and the value shall be 1.
+
+  The cell contains the interrupt number in the range [0-128].
+- ti,intc-size: Number of interrupts handled by the interrupt controller.
+- reg: physical base address and size of the intc registers map.
+
+Example:
+
+	intc: interrupt-controller@1 {
+		compatible = "ti,omap2-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		ti,intc-size = <96>;
+		reg = <0x48200000 0x1000>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/interrupt-controller/via,vt8500-intc.txt b/kernel/Documentation/devicetree/bindings/interrupt-controller/via,vt8500-intc.txt
new file mode 100644
index 000000000..0a4ce1051
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/interrupt-controller/via,vt8500-intc.txt
@@ -0,0 +1,16 @@
+VIA/Wondermedia VT8500 Interrupt Controller
+-----------------------------------------------------
+
+Required properties:
+- compatible : "via,vt8500-intc"
+- reg : Should contain 1 register ranges(address and length)
+- #interrupt-cells : should be <1>
+
+Example:
+
+	intc: interrupt-controller@d8140000 {
+		compatible = "via,vt8500-intc";
+		interrupt-controller;
+		reg = <0xd8140000 0x10000>;
+		#interrupt-cells = <1>;
+	};