These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

17 files changed, 386 insertions, 4 deletions

diff --git a/kernel/Documentation/devicetree/bindings/iio/accel/bma180.txt b/kernel/Documentation/devicetree/bindings/iio/accel/bma180.txt
index c5933573e..4a3679d54 100644
--- a/kernel/Documentation/devicetree/bindings/iio/accel/bma180.txt
+++ b/kernel/Documentation/devicetree/bindings/iio/accel/bma180.txt
@@ -1,10 +1,11 @@
-* Bosch BMA180 triaxial acceleration sensor
+* Bosch BMA180 / BMA250 triaxial acceleration sensor
 
 http://omapworld.com/BMA180_111_1002839.pdf
+http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf
 
 Required properties:
 
-  - compatible : should be "bosch,bma180"
+  - compatible : should be "bosch,bma180" or "bosch,bma250"
   - reg : the I2C address of the sensor
 
 Optional properties:
@@ -13,6 +14,9 @@ Optional properties:
 
   - interrupts : interrupt mapping for GPIO IRQ, it should by configured with
 		flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING
+		For the bma250 the first interrupt listed must be the one
+		connected to the INT1 pin, the second (optional) interrupt
+		listed must be the one connected to the INT2 pin.
 
 Example:
 
diff --git a/kernel/Documentation/devicetree/bindings/iio/accel/lis302.txt b/kernel/Documentation/devicetree/bindings/iio/accel/lis302.txt
new file mode 100644
index 000000000..2a19bff96
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/accel/lis302.txt
@@ -0,0 +1,119 @@
+LIS302 accelerometer devicetree bindings
+
+This device is matched via its bus drivers, and has a number of properties
+that apply in on the generic device (independent from the bus).
+
+
+Required properties for the SPI bindings:
+ - compatible: 		should be set to "st,lis3lv02d_spi"
+ - reg:			the chipselect index
+ - spi-max-frequency:	maximal bus speed, should be set to 1000000 unless
+			constrained by external circuitry
+ - interrupts:		the interrupt generated by the device
+
+Required properties for the I2C bindings:
+ - compatible:		should be set to "st,lis3lv02d"
+ - reg:			i2c slave address
+ - Vdd-supply:		The input supply for Vdd
+ - Vdd_IO-supply:	The input supply for Vdd_IO
+
+
+Optional properties for all bus drivers:
+
+ - st,click-single-{x,y,z}:	if present, tells the device to issue an
+				interrupt on single click events on the
+				x/y/z axis.
+ - st,click-double-{x,y,z}:	if present, tells the device to issue an
+				interrupt on double click events on the
+				x/y/z axis.
+ - st,click-thresh-{x,y,z}:	set the x/y/z axis threshold
+ - st,click-click-time-limit:	click time limit, from 0 to 127.5msec
+				with step of 0.5 msec
+ - st,click-latency:		click latency, from 0 to 255 msec with
+				step of 1 msec.
+ - st,click-window:		click window, from 0 to 255 msec with
+				step of 1 msec.
+ - st,irq{1,2}-disable:		disable IRQ 1/2
+ - st,irq{1,2}-ff-wu-1:		raise IRQ 1/2 on FF_WU_1 condition
+ - st,irq{1,2}-ff-wu-2:		raise IRQ 1/2 on FF_WU_2 condition
+ - st,irq{1,2}-data-ready:	raise IRQ 1/2 on data ready contition
+ - st,irq{1,2}-click:		raise IRQ 1/2 on click condition
+ - st,irq-open-drain:		consider IRQ lines open-drain
+ - st,irq-active-low:		make IRQ lines active low
+ - st,wu-duration-1:		duration register for Free-Fall/Wake-Up
+				interrupt 1
+ - st,wu-duration-2:		duration register for Free-Fall/Wake-Up
+				interrupt 2
+ - st,wakeup-{x,y,z}-{lo,hi}:	set wakeup condition on x/y/z axis for
+				upper/lower limit
+ - st,wakeup-threshold:		set wakeup threshold
+ - st,wakeup2-{x,y,z}-{lo,hi}:	set wakeup condition on x/y/z axis for
+				upper/lower limit for second wakeup
+				engine.
+ - st,wakeup2-threshold:	set wakeup threshold for second wakeup
+				engine.
+ - st,highpass-cutoff-hz=:	1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
+				highpass cut-off frequency
+ - st,hipass{1,2}-disable:	disable highpass 1/2.
+ - st,default-rate=:		set the default rate
+ - st,axis-{x,y,z}=:		set the axis to map to the three coordinates.
+				Negative values can be used for inverted axis.
+ - st,{min,max}-limit-{x,y,z}	set the min/max limits for x/y/z axis
+				(used by self-test)
+
+
+Example for a SPI device node:
+
+	lis302@0 {
+		compatible = "st,lis302dl-spi";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		interrupt-parent = <&gpio>;
+		interrupts = <104 0>;
+
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+		st,click-thresh-x = <10>;
+		st,click-thresh-y = <10>;
+		st,click-thresh-z = <10>;
+		st,irq1-click;
+		st,irq2-click;
+		st,wakeup-x-lo;
+		st,wakeup-x-hi;
+		st,wakeup-y-lo;
+		st,wakeup-y-hi;
+		st,wakeup-z-lo;
+		st,wakeup-z-hi;
+	};
+
+Example for a I2C device node:
+
+	lis331dlh: lis331dlh@18 {
+		compatible = "st,lis331dlh", "st,lis3lv02d";
+		reg = <0x18>;
+		Vdd-supply = <&lis3_reg>;
+		Vdd_IO-supply = <&lis3_reg>;
+
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+		st,click-thresh-x = <10>;
+		st,click-thresh-y = <10>;
+		st,click-thresh-z = <10>;
+		st,irq1-click;
+		st,irq2-click;
+		st,wakeup-x-lo;
+		st,wakeup-x-hi;
+		st,wakeup-y-lo;
+		st,wakeup-y-hi;
+		st,wakeup-z-lo;
+		st,wakeup-z-hi;
+		st,min-limit-x = <120>;
+		st,min-limit-y = <120>;
+		st,min-limit-z = <140>;
+		st,max-limit-x = <550>;
+		st,max-limit-y = <550>;
+		st,max-limit-z = <750>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/kernel/Documentation/devicetree/bindings/iio/accel/mma8452.txt
new file mode 100644
index 000000000..e3c37467d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/accel/mma8452.txt
@@ -0,0 +1,24 @@
+Freescale MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC triaxial accelerometer
+
+Required properties:
+
+  - compatible: should contain one of
+    * "fsl,mma8452"
+    * "fsl,mma8453"
+    * "fsl,mma8652"
+    * "fsl,mma8653"
+  - reg: the I2C address of the chip
+
+Optional properties:
+
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts: interrupt mapping for GPIO IRQ
+
+Example:
+
+	mma8453fc@1d {
+		compatible = "fsl,mma8453";
+		reg = <0x1d>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <5 0>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/iio/adc/berlin2_adc.txt b/kernel/Documentation/devicetree/bindings/iio/adc/berlin2_adc.txt
new file mode 100644
index 000000000..908334c6b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/adc/berlin2_adc.txt
@@ -0,0 +1,19 @@
+* Berlin Analog to Digital Converter (ADC)
+
+The Berlin ADC has 8 channels, with one connected to a temperature sensor.
+It is part of the system controller register set. The ADC node should be a
+sub-node of the system controller node.
+
+Required properties:
+- compatible: must be "marvell,berlin2-adc"
+- interrupts: the interrupts for the ADC and the temperature sensor
+- interrupt-names: should be "adc" and "tsen"
+
+Example:
+
+adc: adc {
+	compatible = "marvell,berlin2-adc";
+	interrupt-parent = <&sic>;
+	interrupts = <12>, <14>;
+	interrupt-names = "adc", "tsen";
+};
diff --git a/kernel/Documentation/devicetree/bindings/iio/adc/hi8435.txt b/kernel/Documentation/devicetree/bindings/iio/adc/hi8435.txt
new file mode 100644
index 000000000..3b0348c5e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/adc/hi8435.txt
@@ -0,0 +1,21 @@
+Holt Integrated Circuits HI-8435 threshold detector bindings
+
+Required properties:
+ - compatible: should be "holt,hi8435"
+ - reg: spi chip select number for the device
+
+Recommended properties:
+ - spi-max-frequency: definition as per
+		Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Optional properties:
+ - gpios: GPIO used for controlling the reset pin
+
+Example:
+sensor@0 {
+	compatible = "holt,hi8435";
+	reg = <0>;
+	gpios = <&gpio6 1 0>;
+
+	spi-max-frequency = <1000000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/iio/adc/mcp320x.txt b/kernel/Documentation/devicetree/bindings/iio/adc/mcp320x.txt
index b85184391..2a1f3af30 100644
--- a/kernel/Documentation/devicetree/bindings/iio/adc/mcp320x.txt
+++ b/kernel/Documentation/devicetree/bindings/iio/adc/mcp320x.txt
@@ -18,6 +18,7 @@ Required properties:
 				"mcp3202"
 				"mcp3204"
 				"mcp3208"
+				"mcp3301"
 
 
 Examples:
diff --git a/kernel/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt b/kernel/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt
index 42ca7deec..15ca6b479 100644
--- a/kernel/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt
+++ b/kernel/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt
@@ -1,7 +1,7 @@
-* Texas Instruments' ADC128S052 ADC chip
+* Texas Instruments' ADC128S052 and ADC122S021 ADC chip
 
 Required properties:
- - compatible: Should be "ti,adc128s052"
+ - compatible: Should be "ti,adc128s052" or "ti,adc122s021"
  - reg: spi chip select number for the device
  - vref-supply: The regulator supply for ADC reference voltage
 
diff --git a/kernel/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt b/kernel/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
index 1a4a43d5c..1aad0514e 100644
--- a/kernel/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
+++ b/kernel/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
@@ -11,6 +11,18 @@ Required properties:
 - clock-names: Must contain "adc", matching entry in the clocks property.
 - vref-supply: The regulator supply ADC reference voltage.
 
+Recommended properties:
+- fsl,adck-max-frequency: Maximum frequencies according to datasheets operating
+  requirements. Three values are required, depending on conversion mode:
+  - Frequency in normal mode (ADLPC=0, ADHSC=0)
+  - Frequency in high-speed mode (ADLPC=0, ADHSC=1)
+  - Frequency in low-power mode (ADLPC=1, ADHSC=0)
+- min-sample-time: Minimum sampling time in nanoseconds. This value has
+  to be chosen according to the conversion mode and the connected analog
+  source resistance (R_as) and capacitance (C_as). Refer the datasheet's
+  operating requirements. A safe default across a wide range of R_as and
+  C_as as well as conversion modes is 1000ns.
+
 Example:
 adc0: adc@4003b000 {
 	compatible = "fsl,vf610-adc";
@@ -18,5 +30,7 @@ adc0: adc@4003b000 {
 	interrupts = <0 53 0x04>;
 	clocks = <&clks VF610_CLK_ADC0>;
 	clock-names = "adc";
+	fsl,adck-max-frequency = <30000000>, <40000000>,
+				<20000000>;
 	vref-supply = <&reg_vcc_3v3_mcu>;
 };
diff --git a/kernel/Documentation/devicetree/bindings/iio/dac/ti,dac7512.txt b/kernel/Documentation/devicetree/bindings/iio/dac/ti,dac7512.txt
new file mode 100644
index 000000000..1db45939d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/dac/ti,dac7512.txt
@@ -0,0 +1,20 @@
+TI DAC7512 DEVICETREE BINDINGS
+
+Required properties:
+
+	- "compatible"		Must be set to "ti,dac7512"
+
+Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
+apply. In particular, "reg" and "spi-max-frequency" properties must be given.
+
+
+Example:
+
+	spi_master {
+		dac7512: dac7512@0 {
+			compatible = "ti,dac7512";
+			reg = <0>; /* CS0 */
+			spi-max-frequency = <1000000>;
+		};
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/kernel/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt
new file mode 100644
index 000000000..e4d8f1c52
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt
@@ -0,0 +1,17 @@
+InvenSense MPU-6050 Six-Axis (Gyro + Accelerometer) MEMS MotionTracking Device
+
+http://www.invensense.com/mems/gyro/mpu6050.html
+
+Required properties:
+ - compatible : should be "invensense,mpu6050"
+ - reg : the I2C address of the sensor
+ - interrupt-parent : should be the phandle for the interrupt controller
+ - interrupts : interrupt mapping for GPIO IRQ
+
+Example:
+	mpu6050@68 {
+		compatible = "invensense,mpu6050";
+		reg = <0x68>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <18 1>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/iio/light/apds9960.txt b/kernel/Documentation/devicetree/bindings/iio/light/apds9960.txt
new file mode 100644
index 000000000..174b709f1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/light/apds9960.txt
@@ -0,0 +1,22 @@
+* Avago APDS9960 gesture/RGB/ALS/proximity sensor
+
+http://www.avagotech.com/docs/AV02-4191EN
+
+Required properties:
+
+  - compatible: must be "avago,apds9960"
+  - reg: the I2c address of the sensor
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts : the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+Example:
+
+apds9960@39 {
+	compatible = "avago,apds9960";
+	reg = <0x39>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 1>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/iio/light/us5182d.txt b/kernel/Documentation/devicetree/bindings/iio/light/us5182d.txt
new file mode 100644
index 000000000..6f0a53014
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/light/us5182d.txt
@@ -0,0 +1,34 @@
+* UPISEMI us5182d I2C ALS and Proximity sensor
+
+Required properties:
+- compatible: must be "upisemi,usd5182"
+- reg: the I2C address of the device
+
+Optional properties:
+- upisemi,glass-coef: glass attenuation factor - compensation factor of
+                      resolution 1000 for material transmittance.
+- upisemi,dark-ths: array of 8 elements containing 16-bit thresholds (adc
+                    counts) corresponding to every scale.
+- upisemi,upper-dark-gain: 8-bit dark gain compensation factor(4 int and 4
+                           fractional bits - Q4.4) applied when light > threshold
+- upisemi,lower-dark-gain: 8-bit dark gain compensation factor(4 int and 4
+                           fractional bits - Q4.4) applied when light < threshold
+
+If the optional properties are not specified these factors will default to the
+values in the below example.
+The glass-coef defaults to no compensation for the covering material.
+The threshold array defaults to experimental values that work with US5182D
+sensor on evaluation board - roughly between 12-32 lux.
+There will be no dark-gain compensation by default when ALS > thresh
+(0 * dark-gain), and a 1.35 compensation factor when ALS < thresh.
+
+Example:
+
+    usd5182@39 {
+                compatible = "upisemi,usd5182";
+                reg = <0x39>;
+                upisemi,glass-coef = < 1000 >;
+                upisemi,dark-ths = /bits/ 16 <170 200 512 512 800 2000 4000 8000>;
+                upisemi,upper-dark-gain = /bits/ 8 <0x00>;
+                upisemi,lower-dark-gain = /bits/ 8 <0x16>;
+    };
diff --git a/kernel/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt b/kernel/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt
new file mode 100644
index 000000000..9f263b7df
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt
@@ -0,0 +1,22 @@
+* Bosch BMC150 magnetometer sensor
+
+http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf
+
+Required properties:
+
+  - compatible : should be "bosch,bmc150_magn"
+  - reg : the I2C address of the magnetometer
+
+Optional properties:
+
+  - interrupt-parent : phandle to the parent interrupt controller
+  - interrupts : interrupt mapping for GPIO IRQ
+
+Example:
+
+bmc150_magn@12 {
+        compatible = "bosch,bmc150_magn";
+        reg = <0x12>;
+        interrupt-parent = <&gpio1>;
+        interrupts = <0 1>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt b/kernel/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt
new file mode 100644
index 000000000..a01235c7f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt
@@ -0,0 +1,13 @@
+* MEMSIC MMC35240 magnetometer sensor
+
+Required properties:
+
+  - compatible : should be "memsic,mmc35240"
+  - reg : the I2C address of the magnetometer
+
+Example:
+
+mmc35240@30 {
+        compatible = "memsic,mmc35240";
+        reg = <0x30>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/iio/pressure/bmp085.txt b/kernel/Documentation/devicetree/bindings/iio/pressure/bmp085.txt
new file mode 100644
index 000000000..d7a6deb6b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/pressure/bmp085.txt
@@ -0,0 +1,24 @@
+BMP085/BMP18x digital pressure sensors
+
+Required properties:
+- compatible: bosch,bmp085
+
+Optional properties:
+- chip-id: configurable chip id for non-default chip revisions
+- temp-measurement-period: temperature measurement period (milliseconds)
+- default-oversampling: default oversampling value to be used at startup,
+  value range is 0-3 with rising sensitivity.
+- interrupt-parent: should be the phandle for the interrupt controller
+- interrupts: interrupt mapping for IRQ
+
+Example:
+
+pressure@77 {
+	compatible = "bosch,bmp085";
+	reg = <0x77>;
+	chip-id = <10>;
+	temp-measurement-period = <100>;
+	default-oversampling = <2>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/iio/st-sensors.txt b/kernel/Documentation/devicetree/bindings/iio/st-sensors.txt
index d2aaca974..d3ccdb190 100644
--- a/kernel/Documentation/devicetree/bindings/iio/st-sensors.txt
+++ b/kernel/Documentation/devicetree/bindings/iio/st-sensors.txt
@@ -30,10 +30,12 @@ Accelerometers:
 - st,lsm330d-accel
 - st,lsm330dl-accel
 - st,lsm330dlc-accel
+- st,lis331dl-accel
 - st,lis331dlh-accel
 - st,lsm303dl-accel
 - st,lsm303dlm-accel
 - st,lsm330-accel
+- st,lsm303agr-accel
 
 Gyroscopes:
 - st,l3g4200d-gyro
@@ -45,6 +47,8 @@ Gyroscopes:
 - st,lsm330-gyro
 
 Magnetometers:
+- st,lsm303agr-magn
+- st,lsm303dlh-magn
 - st,lsm303dlhc-magn
 - st,lsm303dlm-magn
 - st,lis3mdl-magn
diff --git a/kernel/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt b/kernel/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt
new file mode 100644
index 000000000..9be57b036
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt
@@ -0,0 +1,24 @@
+* Melexis MLX90614 contactless IR temperature sensor
+
+http://melexis.com/Infrared-Thermometer-Sensors/Infrared-Thermometer-Sensors/MLX90614-615.aspx
+
+Required properties:
+
+  - compatible: should be "melexis,mlx90614"
+  - reg: the I2C address of the sensor
+
+Optional properties:
+
+  - wakeup-gpios: device tree identifier of the GPIO connected to the SDA line
+      to hold low in order to wake up the device.  In normal operation, the
+      GPIO is set as input and will not interfere in I2C communication.  There
+      is no need for a GPIO driving the SCL line.  If no GPIO is given, power
+      management is disabled.
+
+Example:
+
+mlx90614@5a {
+	compatible = "melexis,mlx90614";
+	reg = <0x5a>;
+	wakeup-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+};