These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

4 files changed, 0 insertions, 134 deletions

diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt
deleted file mode 100644
index 4ab9e2300..000000000
--- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt
+++ /dev/null
@@ -1,66 +0,0 @@
-Device-Tree bindings for tilcdc DRM generic panel output driver
-
-Required properties:
- - compatible: value should be "ti,tilcdc,panel".
- - panel-info: configuration info to configure LCDC correctly for the panel
-   - ac-bias: AC Bias Pin Frequency
-   - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt
-   - dma-burst-sz: DMA burst size
-   - bpp: Bits per pixel
-   - fdd: FIFO DMA Request Delay
-   - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling
-   - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore
-   - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most
-   - fifo-th: DMA FIFO threshold
- - display-timings: typical videomode of lcd panel.  Multiple video modes
-   can be listed if the panel supports multiple timings, but the 'native-mode'
-   should be the preferred/default resolution.  Refer to
-   Documentation/devicetree/bindings/video/display-timing.txt for display
-   timing binding details.
-
-Optional properties:
-- backlight: phandle of the backlight device attached to the panel
-- enable-gpios: GPIO pin to enable or disable the panel
-
-Recommended properties:
- - pinctrl-names, pinctrl-0: the pincontrol settings to configure
-   muxing properly for pins that connect to TFP410 device
-
-Example:
-
-	/* Settings for CDTech_S035Q01 / LCD3 cape: */
-	lcd3 {
-		compatible = "ti,tilcdc,panel";
-		pinctrl-names = "default";
-		pinctrl-0 = <&bone_lcd3_cape_lcd_pins>;
-		backlight = <&backlight>;
-		enable-gpios = <&gpio3 19 0>;
-
-		panel-info {
-			ac-bias           = <255>;
-			ac-bias-intrpt    = <0>;
-			dma-burst-sz      = <16>;
-			bpp               = <16>;
-			fdd               = <0x80>;
-			sync-edge         = <0>;
-			sync-ctrl         = <1>;
-			raster-order      = <0>;
-			fifo-th           = <0>;
-		};
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: 320x240 {
-				hactive         = <320>;
-				vactive         = <240>;
-				hback-porch     = <21>;
-				hfront-porch    = <58>;
-				hsync-len       = <47>;
-				vback-porch     = <11>;
-				vfront-porch    = <23>;
-				vsync-len       = <2>;
-				clock-frequency = <8000000>;
-				hsync-active    = <0>;
-				vsync-active    = <0>;
-			};
-		};
-	};
diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt
deleted file mode 100644
index 3d2c52460..000000000
--- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt
+++ /dev/null
@@ -1,18 +0,0 @@
-Device-Tree bindings for tilcdc DRM encoder slave output driver
-
-Required properties:
- - compatible: value should be "ti,tilcdc,slave".
- - i2c: the phandle for the i2c device the encoder slave is connected to
-
-Recommended properties:
- - pinctrl-names, pinctrl-0: the pincontrol settings to configure
-   muxing properly for pins that connect to TFP410 device
-
-Example:
-
-	hdmi {
-		compatible = "ti,tilcdc,slave";
-		i2c = <&i2c0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
-	};
diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt
deleted file mode 100644
index a58ae7756..000000000
--- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt
+++ /dev/null
@@ -1,21 +0,0 @@
-Device-Tree bindings for tilcdc DRM TFP410 output driver
-
-Required properties:
- - compatible: value should be "ti,tilcdc,tfp410".
- - i2c: the phandle for the i2c device to use for DDC
-
-Recommended properties:
- - pinctrl-names, pinctrl-0: the pincontrol settings to configure
-   muxing properly for pins that connect to TFP410 device
- - powerdn-gpio: the powerdown GPIO, pulled low to power down the
-   TFP410 device (for DPMS_OFF)
-
-Example:
-
-	dvicape {
-		compatible = "ti,tilcdc,tfp410";
-		i2c = <&i2c2>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>;
-		powerdn-gpio = <&gpio2 31 0>;
-	};
diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
deleted file mode 100644
index fff10da5e..000000000
--- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
+++ /dev/null
@@ -1,29 +0,0 @@
-Device-Tree bindings for tilcdc DRM driver
-
-Required properties:
- - compatible: value should be "ti,am33xx-tilcdc".
- - interrupts: the interrupt number
- - reg: base address and size of the LCDC device
-
-Recommended properties:
- - interrupt-parent: the phandle for the interrupt controller that
-   services interrupts for this device.
- - ti,hwmods: Name of the hwmod associated to the LCDC
-
-Optional properties:
- - max-bandwidth: The maximum pixels per second that the memory
-   interface / lcd controller combination can sustain
- - max-width: The maximum horizontal pixel width supported by
-   the lcd controller.
- - max-pixelclock: The maximum pixel clock that can be supported
-   by the lcd controller in KHz.
-
-Example:
-
-	fb: fb@4830e000 {
-		compatible = "ti,am33xx-tilcdc";
-		reg = <0x4830e000 0x1000>;
-		interrupt-parent = <&intc>;
-		interrupts = <36>;
-		ti,hwmods = "lcdc";
-	};