These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 0 insertions, 146 deletions

diff --git a/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt b/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt
deleted file mode 100644
index 9a2136643..000000000
--- a/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt
+++ /dev/null
@@ -1,146 +0,0 @@
-Device-Tree bindings for LVDS Display Bridge (ldb)
-
-LVDS Display Bridge
-===================
-
-The LVDS Display Bridge device tree node contains up to two lvds-channel
-nodes describing each of the two LVDS encoder channels of the bridge.
-
-Required properties:
- - #address-cells : should be <1>
- - #size-cells : should be <0>
- - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
-                Both LDB versions are similar, but i.MX6 has an additional
-                multiplexer in the front to select any of the four IPU display
-                interfaces as input for each LVDS channel.
- - gpr : should be <&gpr> on i.MX53 and i.MX6q.
-         The phandle points to the iomuxc-gpr region containing the LVDS
-         control register.
-- clocks, clock-names : phandles to the LDB divider and selector clocks and to
-                        the display interface selector clocks, as described in
-                        Documentation/devicetree/bindings/clock/clock-bindings.txt
-        The following clocks are expected on i.MX53:
-                "di0_pll" - LDB LVDS channel 0 mux
-                "di1_pll" - LDB LVDS channel 1 mux
-                "di0" - LDB LVDS channel 0 gate
-                "di1" - LDB LVDS channel 1 gate
-                "di0_sel" - IPU1 DI0 mux
-                "di1_sel" - IPU1 DI1 mux
-        On i.MX6q the following additional clocks are needed:
-                "di2_sel" - IPU2 DI0 mux
-                "di3_sel" - IPU2 DI1 mux
-        The needed clock numbers for each are documented in
-        Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
-        Documentation/devicetree/bindings/clock/imx6q-clock.txt.
-
-Optional properties:
- - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
- - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
-               not used on i.MX6q
- - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
-   be configured - one input will be distributed on both outputs in dual
-   channel mode
-
-LVDS Channel
-============
-
-Each LVDS Channel has to contain either an of graph link to a panel device node
-or a display-timings node that describes the video timings for the connected
-LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
-
-Required properties:
- - reg : should be <0> or <1>
- - port: Input and output port nodes with endpoint definitions as defined in
-   Documentation/devicetree/bindings/graph.txt.
-   On i.MX5, the internal two-input-multiplexer is used. Due to hardware
-   limitations, only one input port (port@[0,1]) can be used for each channel
-   (lvds-channel@[0,1], respectively).
-   On i.MX6, there should be four input ports (port@[0-3]) that correspond
-   to the four LVDS multiplexer inputs.
-   A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
-   to a panel input port. Optionally, the output port can be left out if
-   display-timings are used instead.
-
-Optional properties (required if display-timings are used):
- - display-timings : A node that describes the display timings as defined in
-   Documentation/devicetree/bindings/video/display-timing.txt.
- - fsl,data-mapping : should be "spwg" or "jeida"
-                      This describes how the color bits are laid out in the
-                      serialized LVDS signal.
- - fsl,data-width : should be <18> or <24>
-
-example:
-
-gpr: iomuxc-gpr@53fa8000 {
-	/* ... */
-};
-
-ldb: ldb@53fa8008 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	compatible = "fsl,imx53-ldb";
-	gpr = <&gpr>;
-	clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
-		 <&clks IMX5_CLK_LDB_DI1_SEL>,
-		 <&clks IMX5_CLK_IPU_DI0_SEL>,
-		 <&clks IMX5_CLK_IPU_DI1_SEL>,
-		 <&clks IMX5_CLK_LDB_DI0_GATE>,
-		 <&clks IMX5_CLK_LDB_DI1_GATE>;
-	clock-names = "di0_pll", "di1_pll",
-		      "di0_sel", "di1_sel",
-		      "di0", "di1";
-
-	/* Using an of-graph endpoint link to connect the panel */
-	lvds-channel@0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0>;
-
-		port@0 {
-			reg = <0>;
-
-			lvds0_in: endpoint {
-				remote-endpoint = <&ipu_di0_lvds0>;
-			};
-		};
-
-		port@2 {
-			reg = <2>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
-
-	/* Using display-timings and fsl,data-mapping/width instead */
-	lvds-channel@1 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <1>;
-		fsl,data-mapping = "spwg";
-		fsl,data-width = <24>;
-
-		display-timings {
-			/* ... */
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lvds1_in: endpoint {
-				remote-endpoint = <&ipu_di1_lvds1>;
-			};
-		};
-	};
-};
-
-panel: lvds-panel {
-	/* ... */
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds0_out>;
-		};
-	};
-};