These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

12 files changed, 470 insertions, 11 deletions

diff --git a/kernel/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt b/kernel/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
new file mode 100644
index 000000000..47cb1d14b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
@@ -0,0 +1,61 @@
+Analog Device AXI-DMAC DMA controller
+
+Required properties:
+ - compatible: Must be "adi,axi-dmac-1.00.a".
+ - reg: Specification for the controllers memory mapped register map.
+ - interrupts: Specification for the controllers interrupt.
+ - clocks: Phandle and specifier to the controllers AXI interface clock
+ - #dma-cells: Must be 1.
+
+Required sub-nodes:
+ - adi,channels: This sub-node must contain a sub-node for each DMA channel. For
+   the channel sub-nodes the following bindings apply. They must match the
+   configuration options of the peripheral as it was instantiated.
+
+Required properties for adi,channels sub-node:
+ - #size-cells: Must be 0
+ - #address-cells: Must be 1
+
+Required channel sub-node properties:
+ - reg: Which channel this node refers to.
+ - adi,length-width: Width of the DMA transfer length register.
+ - adi,source-bus-width,
+   adi,destination-bus-width: Width of the source or destination bus in bits.
+ - adi,source-bus-type,
+   adi,destination-bus-type: Type of the source or destination bus. Must be one
+   of the following:
+	0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface
+	1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface
+	2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface
+
+Optional channel properties:
+ - adi,cyclic: Must be set if the channel supports hardware cyclic DMA
+   transfers.
+ - adi,2d: Must be set if the channel supports hardware 2D DMA transfers.
+
+DMA clients connected to the AXI-DMAC DMA controller must use the format
+described in the dma.txt file using a one-cell specifier. The value of the
+specifier refers to the DMA channel index.
+
+Example:
+
+dma: dma@7c420000 {
+	compatible = "adi,axi-dmac-1.00.a";
+	reg = <0x7c420000 0x10000>;
+	interrupts = <0 57 0>;
+	clocks = <&clkc 16>;
+	#dma-cells = <1>;
+
+	adi,channels {
+		#size-cells = <0>;
+		#address-cells = <1>;
+
+		dma-channel@0 {
+			reg = <0>;
+			adi,source-bus-width = <32>;
+			adi,source-bus-type = <ADI_AXI_DMAC_TYPE_MM_AXI>;
+			adi,destination-bus-width = <64>;
+			adi,destination-bus-type = <ADI_AXI_DMAC_TYPE_FIFO>;
+		};
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt b/kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt
index d3058768b..c53e0b080 100644
--- a/kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt
@@ -35,7 +35,7 @@ Example:
 			device_type = "dma";
 			reg = <0x0 0x1f270000 0x0 0x10000>,
 			      <0x0 0x1f200000 0x0 0x10000>,
-			      <0x0 0x1b008000 0x0 0x2000>,
+			      <0x0 0x1b000000 0x0 0x400000>,
 			      <0x0 0x1054a000 0x0 0x100>;
 			interrupts = <0x0 0x82 0x4>,
 				     <0x0 0xb8 0x4>,
diff --git a/kernel/Documentation/devicetree/bindings/dma/arm-pl08x.txt b/kernel/Documentation/devicetree/bindings/dma/arm-pl08x.txt
new file mode 100644
index 000000000..8a0097a02
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/arm-pl08x.txt
@@ -0,0 +1,54 @@
+* ARM PrimeCells PL080 and PL081 and derivatives DMA controller
+
+Required properties:
+- compatible: "arm,pl080", "arm,primecell";
+	      "arm,pl081", "arm,primecell";
+- reg: Address range of the PL08x registers
+- interrupt: The PL08x interrupt number
+- clocks: The clock running the IP core clock
+- clock-names: Must contain "apb_pclk"
+- lli-bus-interface-ahb1: if AHB master 1 is eligible for fetching LLIs
+- lli-bus-interface-ahb2: if AHB master 2 is eligible for fetching LLIs
+- mem-bus-interface-ahb1: if AHB master 1 is eligible for fetching memory contents
+- mem-bus-interface-ahb2: if AHB master 2 is eligible for fetching memory contents
+- #dma-cells: must be <2>. First cell should contain the DMA request,
+              second cell should contain either 1 or 2 depending on
+              which AHB master that is used.
+
+Optional properties:
+- dma-channels: contains the total number of DMA channels supported by the DMAC
+- dma-requests: contains the total number of DMA requests supported by the DMAC
+- memcpy-burst-size: the size of the bursts for memcpy: 1, 4, 8, 16, 32
+  64, 128 or 256 bytes are legal values
+- memcpy-bus-width: the bus width used for memcpy: 8, 16 or 32 are legal
+  values
+
+Clients
+Required properties:
+- dmas: List of DMA controller phandle, request channel and AHB master id
+- dma-names: Names of the aforementioned requested channels
+
+Example:
+
+dmac0: dma-controller@10130000 {
+	compatible = "arm,pl080", "arm,primecell";
+	reg = <0x10130000 0x1000>;
+	interrupt-parent = <&vica>;
+	interrupts = <15>;
+	clocks = <&hclkdma0>;
+	clock-names = "apb_pclk";
+	lli-bus-interface-ahb1;
+	lli-bus-interface-ahb2;
+	mem-bus-interface-ahb2;
+	memcpy-burst-size = <256>;
+	memcpy-bus-width = <32>;
+	#dma-cells = <2>;
+};
+
+device@40008000 {
+	...
+	dmas = <&dmac0 0 2
+		&dmac0 1 2>;
+	dma-names = "tx", "rx";
+	...
+};
diff --git a/kernel/Documentation/devicetree/bindings/dma/dma.txt b/kernel/Documentation/devicetree/bindings/dma/dma.txt
index 82104271e..6312fb00c 100644
--- a/kernel/Documentation/devicetree/bindings/dma/dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/dma.txt
@@ -31,6 +31,34 @@ Example:
 		dma-requests = <127>;
 	};
 
+* DMA router
+
+DMA routers are transparent IP blocks used to route DMA request lines from
+devices to the DMA controller. Some SoCs (like TI DRA7x) have more peripherals
+integrated with DMA requests than what the DMA controller can handle directly.
+
+Required property:
+- dma-masters:		phandle of the DMA controller or list of phandles for
+			the DMA controllers the router can direct the signal to.
+- #dma-cells: 		Must be at least 1. Used to provide DMA router specific
+			information. See DMA client binding below for more
+			details.
+
+Optional properties:
+- dma-requests: 	Number of incoming request lines the router can handle.
+- In the node pointed by the dma-masters:
+	- dma-requests:	The router driver might need to look for this in order
+			to configure the routing.
+
+Example:
+	sdma_xbar: dma-router@4a002b78 {
+		compatible = "ti,dra7-dma-crossbar";
+		reg = <0x4a002b78 0xfc>;
+		#dma-cells = <1>;
+		dma-requests = <205>;
+		ti,dma-safe-map = <0>;
+		dma-masters = <&sdma>;
+	};
 
 * DMA client
 
diff --git a/kernel/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt b/kernel/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
new file mode 100644
index 000000000..87740adb2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
@@ -0,0 +1,54 @@
+NXP LPC18xx/43xx DMA MUX (DMA request router)
+
+Required properties:
+- compatible:	"nxp,lpc1850-dmamux"
+- reg:		Memory map for accessing module
+- #dma-cells:	Should be set to <3>.
+		* 1st cell contain the master dma request signal
+		* 2nd cell contain the mux value (0-3) for the peripheral
+		* 3rd cell contain either 1 or 2 depending on the AHB
+		  master used.
+- dma-requests:	Number of DMA requests for the mux
+- dma-masters:	phandle pointing to the DMA controller
+
+The DMA controller node need to have the following poroperties:
+- dma-requests:	Number of DMA requests the controller can handle
+
+Example:
+
+dmac: dma@40002000 {
+	compatible = "nxp,lpc1850-gpdma", "arm,pl080", "arm,primecell";
+	arm,primecell-periphid = <0x00041080>;
+	reg = <0x40002000 0x1000>;
+	interrupts = <2>;
+	clocks = <&ccu1 CLK_CPU_DMA>;
+	clock-names = "apb_pclk";
+	#dma-cells = <2>;
+	dma-channels = <8>;
+	dma-requests = <16>;
+	lli-bus-interface-ahb1;
+	lli-bus-interface-ahb2;
+	mem-bus-interface-ahb1;
+	mem-bus-interface-ahb2;
+	memcpy-burst-size = <256>;
+	memcpy-bus-width = <32>;
+};
+
+dmamux: dma-mux {
+	compatible = "nxp,lpc1850-dmamux";
+	#dma-cells = <3>;
+	dma-requests = <64>;
+	dma-masters = <&dmac>;
+};
+
+uart0: serial@40081000 {
+	compatible = "nxp,lpc1850-uart", "ns16550a";
+	reg = <0x40081000 0x1000>;
+	reg-shift = <2>;
+	interrupts = <24>;
+	clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
+	clock-names = "uartclk", "reg";
+	dmas = <&dmamux 1 1 2
+		&dmamux 2 1 2>;
+	dma-names = "tx", "rx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/dma/mv-xor.txt b/kernel/Documentation/devicetree/bindings/dma/mv-xor.txt
index 7c6cb7fce..276ef815e 100644
--- a/kernel/Documentation/devicetree/bindings/dma/mv-xor.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/mv-xor.txt
@@ -1,7 +1,7 @@
 * Marvell XOR engines
 
 Required properties:
-- compatible: Should be "marvell,orion-xor"
+- compatible: Should be "marvell,orion-xor" or "marvell,armada-380-xor"
 - reg: Should contain registers location and length (two sets)
     the first set is the low registers, the second set the high
     registers for the XOR engine.
@@ -12,10 +12,13 @@ XOR engine has. Those sub-nodes have the following required
 properties:
 - interrupts: interrupt of the XOR channel
 
-And the following optional properties:
+The sub-nodes used to contain one or several of the following
+properties, but they are now deprecated:
 - dmacap,memcpy to indicate that the XOR channel is capable of memcpy operations
 - dmacap,memset to indicate that the XOR channel is capable of memset operations
 - dmacap,xor to indicate that the XOR channel is capable of xor operations
+- dmacap,interrupt to indicate that the XOR channel is capable of
+  generating interrupts
 
 Example:
 
@@ -28,13 +31,8 @@ xor@d0060900 {
 
 	xor00 {
 	      interrupts = <51>;
-	      dmacap,memcpy;
-	      dmacap,xor;
 	};
 	xor01 {
 	      interrupts = <52>;
-	      dmacap,memcpy;
-	      dmacap,xor;
-	      dmacap,memset;
 	};
 };
diff --git a/kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt b/kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt
index ecbc96ad3..ccd52d6a2 100644
--- a/kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt
@@ -3,7 +3,8 @@
 See dma.txt first
 
 Required properties:
-- compatible: Should be "sirf,prima2-dmac" or "sirf,marco-dmac"
+- compatible: Should be "sirf,prima2-dmac", "sirf,atlas7-dmac" or
+  "sirf,atlas7-dmac-v2"
 - reg: Should contain DMA registers location and length.
 - interrupts: Should contain one interrupt shared by all channel
 - #dma-cells: must be <1>. used to represent the number of integer
diff --git a/kernel/Documentation/devicetree/bindings/dma/sun4i-dma.txt b/kernel/Documentation/devicetree/bindings/dma/sun4i-dma.txt
new file mode 100644
index 000000000..f1634a27a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/sun4i-dma.txt
@@ -0,0 +1,46 @@
+Allwinner A10 DMA Controller
+
+This driver follows the generic DMA bindings defined in dma.txt.
+
+Required properties:
+
+- compatible:	Must be "allwinner,sun4i-a10-dma"
+- reg:		Should contain the registers base address and length
+- interrupts:	Should contain a reference to the interrupt used by this device
+- clocks:	Should contain a reference to the parent AHB clock
+- #dma-cells :	Should be 2, first cell denoting normal or dedicated dma,
+		second cell holding the request line number.
+
+Example:
+	dma: dma-controller@01c02000 {
+		compatible = "allwinner,sun4i-a10-dma";
+		reg = <0x01c02000 0x1000>;
+		interrupts = <27>;
+		clocks = <&ahb_gates 6>;
+		#dma-cells = <2>;
+	};
+
+Clients:
+
+DMA clients connected to the Allwinner A10 DMA controller must use the
+format described in the dma.txt file, using a three-cell specifier for
+each channel: a phandle plus two integer cells.
+The three cells in order are:
+
+1. A phandle pointing to the DMA controller.
+2. Whether it is using normal (0) or dedicated (1) channels
+3. The port ID as specified in the datasheet
+
+Example:
+	spi2: spi@01c17000 {
+		compatible = "allwinner,sun4i-a10-spi";
+		reg = <0x01c17000 0x1000>;
+		interrupts = <0 12 4>;
+		clocks = <&ahb_gates 22>, <&spi2_clk>;
+		clock-names = "ahb", "mod";
+		dmas = <&dma 1 29>, <&dma 1 28>;
+		dma-names = "rx", "tx";
+		status = "disabled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt
index 9cdcba24d..d13c136ce 100644
--- a/kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt
@@ -4,7 +4,10 @@ This driver follows the generic DMA bindings defined in dma.txt.
 
 Required properties:
 
-- compatible:	Must be "allwinner,sun6i-a31-dma" or "allwinner,sun8i-a23-dma"
+- compatible:	Must be one of
+		  "allwinner,sun6i-a31-dma"
+		  "allwinner,sun8i-a23-dma"
+		  "allwinner,sun8i-h3-dma"
 - reg:		Should contain the registers base address and length
 - interrupts:	Should contain a reference to the interrupt used by this device
 - clocks:	Should contain a reference to the parent AHB clock
diff --git a/kernel/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt b/kernel/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt
new file mode 100644
index 000000000..b152a75dc
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt
@@ -0,0 +1,63 @@
+Texas Instruments DMA Crossbar (DMA request router)
+
+Required properties:
+- compatible:	"ti,dra7-dma-crossbar" for DRA7xx DMA crossbar
+		"ti,am335x-edma-crossbar" for AM335x and AM437x
+- reg:		Memory map for accessing module
+- #dma-cells:	Should be set to to match with the DMA controller's dma-cells
+		for ti,dra7-dma-crossbar and <3> for ti,am335x-edma-crossbar.
+- dma-requests:	Number of DMA requests the crossbar can receive
+- dma-masters:	phandle pointing to the DMA controller
+
+The DMA controller node need to have the following poroperties:
+- dma-requests:	Number of DMA requests the controller can handle
+
+Optional properties:
+- ti,dma-safe-map: Safe routing value for unused request lines
+
+Notes:
+When requesting channel via ti,dra7-dma-crossbar, the DMA clinet must request
+the DMA event number as crossbar ID (input to the DMA crossbar).
+
+For ti,am335x-edma-crossbar: the meaning of parameters of dmas for clients:
+dmas = <&edma_xbar 12 0 1>; where <12> is the DMA request number, <0> is the TC
+the event should be assigned and <1> is the mux selection for in the crossbar.
+When mux 0 is used the DMA channel can be requested directly from edma node.
+
+Example:
+
+/* DMA controller */
+sdma: dma-controller@4a056000 {
+	compatible = "ti,omap4430-sdma";
+	reg = <0x4a056000 0x1000>;
+	interrupts =	<GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+	#dma-cells = <1>;
+	dma-channels = <32>;
+	dma-requests = <127>;
+};
+
+/* DMA crossbar */
+sdma_xbar: dma-router@4a002b78 {
+	compatible = "ti,dra7-dma-crossbar";
+	reg = <0x4a002b78 0xfc>;
+	#dma-cells = <1>;
+	dma-requests = <205>;
+	ti,dma-safe-map = <0>;
+	dma-masters = <&sdma>;
+};
+
+/* DMA client */
+uart1: serial@4806a000 {
+	compatible = "ti,omap4-uart";
+	reg = <0x4806a000 0x100>;
+	interrupts-extended = <&gic GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+	ti,hwmods = "uart1";
+	clock-frequency = <48000000>;
+	status = "disabled";
+	/* Requesting crossbar input 49 and 50 */
+	dmas = <&sdma_xbar 49>, <&sdma_xbar 50>;
+	dma-names = "tx", "rx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/dma/ti-edma.txt b/kernel/Documentation/devicetree/bindings/dma/ti-edma.txt
index 5ba525a10..079b42a81 100644
--- a/kernel/Documentation/devicetree/bindings/dma/ti-edma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/ti-edma.txt
@@ -1,4 +1,117 @@
-TI EDMA
+Texas Instruments eDMA
+
+The eDMA3 consists of two components: Channel controller (CC) and Transfer
+Controller(s) (TC). The CC is the main entry for DMA users since it is
+responsible for the DMA channel handling, while the TCs are responsible to
+execute the actual DMA tansfer.
+
+------------------------------------------------------------------------------
+eDMA3 Channel Controller
+
+Required properties:
+- compatible:	"ti,edma3-tpcc" for the channel controller(s)
+- #dma-cells:	Should be set to <2>. The first number is the DMA request
+		number and the second is the TC the channel is serviced on.
+- reg:		Memory map of eDMA CC
+- reg-names:	"edma3_cc"
+- interrupts:	Interrupt lines for CCINT, MPERR and CCERRINT.
+- interrupt-names: "edma3_ccint", "emda3_mperr" and "edma3_ccerrint"
+- ti,tptcs:	List of TPTCs associated with the eDMA in the following form:
+		<&tptc_phandle TC_priority_number>. The highest priority is 0.
+
+Optional properties:
+- ti,hwmods:	Name of the hwmods associated to the eDMA CC
+- ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow
+		these channels will be SW triggered channels. See example.
+- ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by
+		the driver, they are allocated to be used by for example the
+		DSP. See example.
+
+------------------------------------------------------------------------------
+eDMA3 Transfer Controller
+
+Required properties:
+- compatible:	"ti,edma3-tptc" for the transfer controller(s)
+- reg:		Memory map of eDMA TC
+- interrupts:	Interrupt number for TCerrint.
+
+Optional properties:
+- ti,hwmods:	Name of the hwmods associated to the given eDMA TC
+- interrupt-names: "edma3_tcerrint"
+
+------------------------------------------------------------------------------
+Example:
+
+edma: edma@49000000 {
+	compatible = "ti,edma3-tpcc";
+	ti,hwmods = "tpcc";
+	reg =	<0x49000000 0x10000>;
+	reg-names = "edma3_cc";
+	interrupts = <12 13 14>;
+	interrupt-names = "edma3_ccint", "emda3_mperr", "edma3_ccerrint";
+	dma-requests = <64>;
+	#dma-cells = <2>;
+
+	ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 7>, <&edma_tptc2 0>;
+
+	/* Channel 20 and 21 is allocated for memcpy */
+	ti,edma-memcpy-channels = <20 21>;
+	/* The following PaRAM slots are reserved: 35-44 and 100-109 */
+	ti,edma-reserved-slot-ranges = <35 10>, <100 10>;
+};
+
+edma_tptc0: tptc@49800000 {
+	compatible = "ti,edma3-tptc";
+	ti,hwmods = "tptc0";
+	reg =	<0x49800000 0x100000>;
+	interrupts = <112>;
+	interrupt-names = "edm3_tcerrint";
+};
+
+edma_tptc1: tptc@49900000 {
+	compatible = "ti,edma3-tptc";
+	ti,hwmods = "tptc1";
+	reg =	<0x49900000 0x100000>;
+	interrupts = <113>;
+	interrupt-names = "edm3_tcerrint";
+};
+
+edma_tptc2: tptc@49a00000 {
+	compatible = "ti,edma3-tptc";
+	ti,hwmods = "tptc2";
+	reg =	<0x49a00000 0x100000>;
+	interrupts = <114>;
+	interrupt-names = "edm3_tcerrint";
+};
+
+sham: sham@53100000 {
+	compatible = "ti,omap4-sham";
+	ti,hwmods = "sham";
+	reg = <0x53100000 0x200>;
+	interrupts = <109>;
+	/* DMA channel 36 executed on eDMA TC0 - low priority queue */
+	dmas = <&edma 36 0>;
+	dma-names = "rx";
+};
+
+mcasp0: mcasp@48038000 {
+	compatible = "ti,am33xx-mcasp-audio";
+	ti,hwmods = "mcasp0";
+	reg = <0x48038000 0x2000>,
+		<0x46000000 0x400000>;
+	reg-names = "mpu", "dat";
+	interrupts = <80>, <81>;
+	interrupt-names = "tx", "rx";
+	status = "disabled";
+	/* DMA channels 8 and 9 executed on eDMA TC2 - high priority queue */
+	dmas = <&edma 8 2>,
+	       <&edma 9 2>;
+	dma-names = "tx", "rx";
+};
+
+------------------------------------------------------------------------------
+DEPRECATED binding, new DTS files must use the ti,edma3-tpcc/ti,edma3-tptc
+binding.
 
 Required properties:
 - compatible : "ti,edma3"
diff --git a/kernel/Documentation/devicetree/bindings/dma/zxdma.txt b/kernel/Documentation/devicetree/bindings/dma/zxdma.txt
new file mode 100644
index 000000000..3207ceb04
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/zxdma.txt
@@ -0,0 +1,38 @@
+* ZTE ZX296702 DMA controller
+
+Required properties:
+- compatible: Should be "zte,zx296702-dma"
+- reg: Should contain DMA registers location and length.
+- interrupts: Should contain one interrupt shared by all channel
+- #dma-cells: see dma.txt, should be 1, para number
+- dma-channels: physical channels supported
+- dma-requests: virtual channels supported, each virtual channel
+		have specific request line
+- clocks: clock required
+
+Example:
+
+Controller:
+	dma: dma-controller@0x09c00000{
+		compatible = "zte,zx296702-dma";
+		reg = <0x09c00000 0x1000>;
+		clocks = <&topclk ZX296702_DMA_ACLK>;
+		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		dma-channels = <24>;
+		dma-requests = <24>;
+	};
+
+Client:
+Use specific request line passing from dmax
+For example, spdif0 tx channel request line is 4
+	spdif0: spdif0@0b004000 {
+		#sound-dai-cells = <0>;
+		compatible = "zte,zx296702-spdif";
+		reg = <0x0b004000 0x1000>;
+		clocks = <&lsp0clk ZX296702_SPDIF0_DIV>;
+		clock-names = "tx";
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&dma 4>;
+		dma-names = "tx";
+	}