These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 105 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt b/kernel/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt
new file mode 100644
index 000000000..971c3eedb
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt
@@ -0,0 +1,105 @@
+Freescale i.MX DRM master device
+================================
+
+The freescale i.MX DRM master device is a virtual device needed to list all
+IPU or other display interface nodes that comprise the graphics subsystem.
+
+Required properties:
+- compatible: Should be "fsl,imx-display-subsystem"
+- ports: Should contain a list of phandles pointing to display interface ports
+  of IPU devices
+
+example:
+
+display-subsystem {
+	compatible = "fsl,display-subsystem";
+	ports = <&ipu_di0>;
+};
+
+
+Freescale i.MX IPUv3
+====================
+
+Required properties:
+- compatible: Should be "fsl,<chip>-ipu"
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain sync interrupt and error interrupt,
+  in this order.
+- resets: phandle pointing to the system reset controller and
+          reset line index, see reset/fsl,imx-src.txt for details
+Optional properties:
+- port@[0-3]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Ports 0 and 1 should correspond to CSI0 and CSI1,
+  ports 2 and 3 should correspond to DI0 and DI1, respectively.
+
+example:
+
+ipu: ipu@18000000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx53-ipu";
+	reg = <0x18000000 0x080000000>;
+	interrupts = <11 10>;
+	resets = <&src 2>;
+
+	ipu_di0: port@2 {
+		reg = <2>;
+
+		ipu_di0_disp0: endpoint {
+			remote-endpoint = <&display_in>;
+		};
+	};
+};
+
+Parallel display support
+========================
+
+Required properties:
+- compatible: Should be "fsl,imx-parallel-display"
+Optional properties:
+- interface_pix_fmt: How this display is connected to the
+  display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
+  and "lvds666".
+- edid: verbatim EDID data block describing attached display.
+- ddc: phandle describing the i2c bus handling the display data
+  channel
+- port@[0-1]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Port 0 is the input port connected to the IPU display interface,
+  port 1 is the output port connected to a panel.
+
+example:
+
+display@di0 {
+	compatible = "fsl,imx-parallel-display";
+	edid = [edid-data];
+	interface-pix-fmt = "rgb24";
+
+	port@0 {
+		reg = <0>;
+
+		display_in: endpoint {
+			remote-endpoint = <&ipu_di0_disp0>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+panel {
+	...
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&display_out>;
+		};
+	};
+};