Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

1 files changed, 130 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/kernel/Documentation/devicetree/bindings/bus/ti-gpmc.txt
new file mode 100644
index 000000000..704be9306
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/bus/ti-gpmc.txt
@@ -0,0 +1,130 @@
+Device tree bindings for OMAP general purpose memory controllers (GPMC)
+
+The actual devices are instantiated from the child nodes of a GPMC node.
+
+Required properties:
+
+ - compatible:		Should be set to one of the following:
+
+			ti,omap2420-gpmc (omap2420)
+			ti,omap2430-gpmc (omap2430)
+			ti,omap3430-gpmc (omap3430 & omap3630)
+			ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
+			ti,am3352-gpmc   (am335x devices)
+
+ - reg:			A resource specifier for the register space
+			(see the example below)
+ - ti,hwmods:		Should be set to "ti,gpmc" until the DT transition is
+			completed.
+ - #address-cells:	Must be set to 2 to allow memory address translation
+ - #size-cells:		Must be set to 1 to allow CS address passing
+ - gpmc,num-cs:		The maximum number of chip-select lines that controller
+			can support.
+ - gpmc,num-waitpins:	The maximum number of wait pins that controller can
+			support.
+ - ranges:		Must be set up to reflect the memory layout with four
+			integer values for each chip-select line in use:
+
+			   <cs-number> 0 <physical address of mapping> <size>
+
+			Currently, calculated values derived from the contents
+			of the per-CS register GPMC_CONFIG7 (as set up by the
+			bootloader) are used for the physical address decoding.
+			As this will change in the future, filling correct
+			values here is a requirement.
+
+Timing properties for child nodes. All are optional and default to 0.
+
+ - gpmc,sync-clk-ps:	Minimum clock period for synchronous mode, in picoseconds
+
+ Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2:
+ - gpmc,cs-on-ns:	Assertion time
+ - gpmc,cs-rd-off-ns:	Read deassertion time
+ - gpmc,cs-wr-off-ns:	Write deassertion time
+
+ ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3:
+ - gpmc,adv-on-ns:	Assertion time
+ - gpmc,adv-rd-off-ns:	Read deassertion time
+ - gpmc,adv-wr-off-ns:	Write deassertion time
+
+ WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
+ - gpmc,we-on-ns	Assertion time
+ - gpmc,we-off-ns:	Deassertion time
+
+ OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
+ - gpmc,oe-on-ns:	Assertion time
+ - gpmc,oe-off-ns:	Deassertion time
+
+ Access time and cycle time timings (in nanoseconds) corresponding to
+ GPMC_CONFIG5:
+ - gpmc,page-burst-access-ns: 	Multiple access word delay
+ - gpmc,access-ns:		Start-cycle to first data valid delay
+ - gpmc,rd-cycle-ns:		Total read cycle time
+ - gpmc,wr-cycle-ns:		Total write cycle time
+ - gpmc,bus-turnaround-ns:	Turn-around time between successive accesses
+ - gpmc,cycle2cycle-delay-ns:	Delay between chip-select pulses
+ - gpmc,clk-activation-ns: 	GPMC clock activation time
+ - gpmc,wait-monitoring-ns:	Start of wait monitoring with regard to valid
+				data
+
+Boolean timing parameters. If property is present parameter enabled and
+disabled if omitted:
+ - gpmc,adv-extra-delay:	ADV signal is delayed by half GPMC clock
+ - gpmc,cs-extra-delay:		CS signal is delayed by half GPMC clock
+ - gpmc,cycle2cycle-diffcsen:	Add "cycle2cycle-delay" between successive
+				accesses to a different CS
+ - gpmc,cycle2cycle-samecsen:	Add "cycle2cycle-delay" between successive
+				accesses to the same CS
+ - gpmc,oe-extra-delay:		OE signal is delayed by half GPMC clock
+ - gpmc,we-extra-delay:		WE signal is delayed by half GPMC clock
+ - gpmc,time-para-granularity:	Multiply all access times by 2
+
+The following are only applicable to OMAP3+ and AM335x:
+ - gpmc,wr-access-ns:		In synchronous write mode, for single or
+				burst accesses, defines the number of
+				GPMC_FCLK cycles from start access time
+				to the GPMC_CLK rising edge used by the
+				memory device for the first data capture.
+ - gpmc,wr-data-mux-bus-ns:	In address-data multiplex mode, specifies
+				the time when the first data is driven on
+				the address-data bus.
+
+GPMC chip-select settings properties for child nodes. All are optional.
+
+- gpmc,burst-length	Page/burst length. Must be 4, 8 or 16.
+- gpmc,burst-wrap	Enables wrap bursting
+- gpmc,burst-read	Enables read page/burst mode
+- gpmc,burst-write	Enables write page/burst mode
+- gpmc,device-width	Total width of device(s) connected to a GPMC
+			chip-select in bytes. The GPMC supports 8-bit
+			and 16-bit devices and so this property must be
+			1 or 2.
+- gpmc,mux-add-data	Address and data multiplexing configuration.
+			Valid values are 1 for address-address-data
+			multiplexing mode and 2 for address-data
+			multiplexing mode.
+- gpmc,sync-read	Enables synchronous read. Defaults to asynchronous
+			is this is not set.
+- gpmc,sync-write	Enables synchronous writes. Defaults to asynchronous
+			is this is not set.
+- gpmc,wait-pin		Wait-pin used by client. Must be less than
+			"gpmc,num-waitpins".
+- gpmc,wait-on-read	Enables wait monitoring on reads.
+- gpmc,wait-on-write	Enables wait monitoring on writes.
+
+Example for an AM33xx board:
+
+	gpmc: gpmc@50000000 {
+		compatible = "ti,am3352-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x50000000 0x2000>;
+		interrupts = <100>;
+
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <2>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+
+		/* child nodes go here */
+	};