These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 139 insertions, 10 deletions

diff --git a/kernel/Documentation/ABI/testing/sysfs-bus-iio b/kernel/Documentation/ABI/testing/sysfs-bus-iio
index 1fbdd79d1..0439c2aaf 100644
--- a/kernel/Documentation/ABI/testing/sysfs-bus-iio
+++ b/kernel/Documentation/ABI/testing/sysfs-bus-iio
@@ -71,6 +71,8 @@ Description:
 
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_raw
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_i_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_q_raw
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -81,6 +83,11 @@ Description:
 		unique to allow association with event codes. Units after
 		application of scale and offset are millivolts.
 
+		Channels with 'i' and 'q' modifiers always exist in pairs and both
+		channels refer to the same signal. The 'i' channel contains the in-phase
+		component of the signal while the 'q' channel contains the quadrature
+		component.
+
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY-voltageZ_raw
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
@@ -246,8 +253,16 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_accel_y_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_z_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_i_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_q_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_q_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_i_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_current_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_i_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_q_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_current_q_offset
+What:		/sys/bus/iio/devices/iio:deviceX/in_current_i_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_tempY_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_temp_offset
 What:		/sys/bus/iio/devices/iio:deviceX/in_pressureY_offset
@@ -273,14 +288,22 @@ Description:
 		to the _raw output.
 
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_i_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_q_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_i_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_q_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltage-voltage_scale
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_supply_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_current_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_i_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_q_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_current_i_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_current_q_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_peak_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_anglvel_scale
@@ -328,6 +351,10 @@ Description:
 
 What		/sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale
 What		/sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_calibscale
+What		/sys/bus/iio/devices/iio:deviceX/in_voltageY_i_calibscale
+What		/sys/bus/iio/devices/iio:deviceX/in_voltageY_q_calibscale
+What		/sys/bus/iio/devices/iio:deviceX/in_voltage_i_calibscale
+What		/sys/bus/iio/devices/iio:deviceX/in_voltage_q_calibscale
 What		/sys/bus/iio/devices/iio:deviceX/in_voltage_calibscale
 What		/sys/bus/iio/devices/iio:deviceX/in_accel_x_calibscale
 What		/sys/bus/iio/devices/iio:deviceX/in_accel_y_calibscale
@@ -386,6 +413,11 @@ Description:
 		to compute the calories burnt by the user.
 
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_scale_available
+What:		/sys/.../iio:deviceX/in_anglvel_scale_available
+What:		/sys/.../iio:deviceX/in_magn_scale_available
+What:		/sys/.../iio:deviceX/in_illuminance_scale_available
+What:		/sys/.../iio:deviceX/in_intensity_scale_available
+What:		/sys/.../iio:deviceX/in_proximity_scale_available
 What:		/sys/.../iio:deviceX/in_voltageX_scale_available
 What:		/sys/.../iio:deviceX/in_voltage-voltage_scale_available
 What:		/sys/.../iio:deviceX/out_voltageX_scale_available
@@ -420,6 +452,16 @@ Description:
 		to the underlying data channel, then this parameter
 		gives the 3dB frequency of the filter in Hz.
 
+What:		/sys/.../in_accel_filter_high_pass_3db_frequency
+What:		/sys/.../in_anglvel_filter_high_pass_3db_frequency
+What:		/sys/.../in_magn_filter_high_pass_3db_frequency
+KernelVersion:	4.2
+Contact:	linux-iio@vger.kernel.org
+Description:
+		If a known or controllable high pass filter is applied
+		to the underlying data channel, then this parameter
+		gives the 3dB frequency of the filter in Hz.
+
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_raw
 What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_raw
 KernelVersion:	2.6.37
@@ -451,7 +493,7 @@ Contact:	linux-iio@vger.kernel.org
 Description:
 		Specifies the output powerdown mode.
 		DAC output stage is disconnected from the amplifier and
-		1kohm_to_gnd: connected	to ground via an 1kOhm resistor,
+		1kohm_to_gnd: connected to ground via an 1kOhm resistor,
 		6kohm_to_gnd: connected to ground via a 6kOhm resistor,
 		20kohm_to_gnd: connected to ground via a 20kOhm resistor,
 		100kohm_to_gnd: connected to ground via an 100kOhm resistor,
@@ -461,9 +503,9 @@ Description:
 		outX_powerdown_mode_available. If Y is not present the
 		mode is shared across all outputs.
 
-What:		/sys/.../iio:deviceX/out_votlageY_powerdown_mode_available
+What:		/sys/.../iio:deviceX/out_voltageY_powerdown_mode_available
 What:		/sys/.../iio:deviceX/out_voltage_powerdown_mode_available
-What:		/sys/.../iio:deviceX/out_altvotlageY_powerdown_mode_available
+What:		/sys/.../iio:deviceX/out_altvoltageY_powerdown_mode_available
 What:		/sys/.../iio:deviceX/out_altvoltage_powerdown_mode_available
 KernelVersion:	2.6.38
 Contact:	linux-iio@vger.kernel.org
@@ -539,6 +581,7 @@ What:		/sys/.../iio:deviceX/events/in_voltageY_supply_thresh_rising_en
 What:		/sys/.../iio:deviceX/events/in_voltageY_supply_thresh_falling_en
 What:		/sys/.../iio:deviceX/events/in_voltageY_thresh_rising_en
 What:		/sys/.../iio:deviceX/events/in_voltageY_thresh_falling_en
+What:		/sys/.../iio:deviceX/events/in_voltageY_thresh_either_en
 What:		/sys/.../iio:deviceX/events/in_tempY_thresh_rising_en
 What:		/sys/.../iio:deviceX/events/in_tempY_thresh_falling_en
 KernelVersion:	2.6.37
@@ -880,6 +923,26 @@ Description:
 		met before an event is generated. If direction is not
 		specified then this period applies to both directions.
 
+What:		/sys/.../events/in_accel_thresh_rising_low_pass_filter_3db
+What:		/sys/.../events/in_anglvel_thresh_rising_low_pass_filter_3db
+What:		/sys/.../events/in_magn_thresh_rising_low_pass_filter_3db
+KernelVersion:	4.2
+Contact:	linux-iio@vger.kernel.org
+Description:
+		If a low pass filter can be applied to the event generation
+		this property gives its 3db frequency in Hz.
+		A value of zero disables the filter.
+
+What:		/sys/.../events/in_accel_thresh_rising_high_pass_filter_3db
+What:		/sys/.../events/in_anglvel_thresh_rising_high_pass_filter_3db
+What:		/sys/.../events/in_magn_thresh_rising_high_pass_filter_3db
+KernelVersion:	4.2
+Contact:	linux-iio@vger.kernel.org
+Description:
+		If a high pass filter can be applied to the event generation
+		this property gives its 3db frequency in Hz.
+		A value of zero disables the filter.
+
 What:		/sys/.../events/in_activity_still_thresh_rising_en
 What:		/sys/.../events/in_activity_still_thresh_falling_en
 What:		/sys/.../events/in_activity_walking_thresh_rising_en
@@ -978,13 +1041,6 @@ Contact:	linux-iio@vger.kernel.org
 Description:
 		Number of scans contained by the buffer.
 
-What:		/sys/bus/iio/devices/iio:deviceX/buffer/bytes_per_datum
-KernelVersion:	2.6.37
-Contact:	linux-iio@vger.kernel.org
-Description:
-		Bytes per scan.  Due to alignment fun, the scan may be larger
-		than implied directly by the scan_element parameters.
-
 What:		/sys/bus/iio/devices/iio:deviceX/buffer/enable
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
@@ -1016,6 +1072,10 @@ What:		/sys/.../iio:deviceX/scan_elements/in_timestamp_en
 What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_supply_en
 What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_en
 What:		/sys/.../iio:deviceX/scan_elements/in_voltageY-voltageZ_en
+What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_i_en
+What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_q_en
+What:		/sys/.../iio:deviceX/scan_elements/in_voltage_i_en
+What:		/sys/.../iio:deviceX/scan_elements/in_voltage_q_en
 What:		/sys/.../iio:deviceX/scan_elements/in_incli_x_en
 What:		/sys/.../iio:deviceX/scan_elements/in_incli_y_en
 What:		/sys/.../iio:deviceX/scan_elements/in_pressureY_en
@@ -1034,6 +1094,10 @@ What:		/sys/.../iio:deviceX/scan_elements/in_incli_type
 What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_type
 What:		/sys/.../iio:deviceX/scan_elements/in_voltage_type
 What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_supply_type
+What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_i_type
+What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_q_type
+What:		/sys/.../iio:deviceX/scan_elements/in_voltage_i_type
+What:		/sys/.../iio:deviceX/scan_elements/in_voltage_q_type
 What:		/sys/.../iio:deviceX/scan_elements/in_timestamp_type
 What:		/sys/.../iio:deviceX/scan_elements/in_pressureY_type
 What:		/sys/.../iio:deviceX/scan_elements/in_pressure_type
@@ -1071,6 +1135,10 @@ Description:
 
 What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_index
 What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_supply_index
+What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_i_index
+What:		/sys/.../iio:deviceX/scan_elements/in_voltageY_q_index
+What:		/sys/.../iio:deviceX/scan_elements/in_voltage_i_index
+What:		/sys/.../iio:deviceX/scan_elements/in_voltage_q_index
 What:		/sys/.../iio:deviceX/scan_elements/in_accel_x_index
 What:		/sys/.../iio:deviceX/scan_elements/in_accel_y_index
 What:		/sys/.../iio:deviceX/scan_elements/in_accel_z_index
@@ -1228,6 +1296,8 @@ Description:
 		or without compensation from tilt sensors.
 
 What:		/sys/bus/iio/devices/iio:deviceX/in_currentX_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentX_i_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentX_q_raw
 KernelVersion:	3.18
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -1236,6 +1306,11 @@ Description:
 		present, output should be considered as processed with the
 		unit in milliamps.
 
+		Channels with 'i' and 'q' modifiers always exist in pairs and both
+		channels refer to the same signal. The 'i' channel contains the in-phase
+		component of the signal while the 'q' channel contains the quadrature
+		component.
+
 What:		/sys/.../iio:deviceX/in_energy_en
 What:		/sys/.../iio:deviceX/in_distance_en
 What:		/sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_en
@@ -1362,3 +1437,57 @@ Description:
 		hwfifo_watermak_min but not equal to any of the values in this
 		list, the driver will chose an appropriate value for the
 		hardware fifo watermark level.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_temp_calibemissivity
+What:		/sys/bus/iio/devices/iio:deviceX/in_tempX_calibemissivity
+What:		/sys/bus/iio/devices/iio:deviceX/in_temp_object_calibemissivity
+What:		/sys/bus/iio/devices/iio:deviceX/in_tempX_object_calibemissivity
+KernelVersion:	4.1
+Contact:	linux-iio@vger.kernel.org
+Description:
+		The emissivity ratio of the surface in the field of view of the
+		contactless temperature sensor.  Emissivity varies from 0 to 1,
+		with 1 being the emissivity of a black body.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_magn_x_oversampling_ratio
+What:		/sys/bus/iio/devices/iio:deviceX/in_magn_y_oversampling_ratio
+What:		/sys/bus/iio/devices/iio:deviceX/in_magn_z_oversampling_ratio
+KernelVersion:	4.2
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Hardware applied number of measurements for acquiring one
+		data point. The HW will do <type>[_name]_oversampling_ratio
+		measurements and return the average value as output data. Each
+		value resulted from <type>[_name]_oversampling_ratio measurements
+		is considered as one sample for <type>[_name]_sampling_frequency.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_concentration_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_concentrationX_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_concentration_co2_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_concentrationX_co2_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_concentration_voc_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_concentrationX_voc_raw
+KernelVersion:	4.3
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Raw (unscaled no offset etc.) percentage reading of a substance.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_resistance_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_resistanceX_raw
+What:		/sys/bus/iio/devices/iio:deviceX/out_resistance_raw
+What:		/sys/bus/iio/devices/iio:deviceX/out_resistanceX_raw
+KernelVersion:	4.3
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Raw (unscaled no offset etc.) resistance reading that can be processed
+		into an ohm value.
+
+What:		/sys/bus/iio/devices/iio:deviceX/heater_enable
+KernelVersion:	4.1.0
+Contact:	linux-iio@vger.kernel.org
+Description:
+		'1' (enable) or '0' (disable) specifying the enable
+		of heater function. Same reading values apply
+		This ABI is especially applicable for humidity sensors
+		to heatup the device and get rid of any condensation
+		in some humidity environment