1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
|
================================================
Set up a Service VM Running as a vRouter (SLAAC)
================================================
| # Current network setup for IPv6 router VM on local virtualbox setup
| # /etc/sysconfig/network-scripts/ifcfg-enp0s3
| # Network interface enp0s3 is IPv4 for public internet access
| TYPE="Ethernet"
| BOOTPROTO="dhcp"
| DEFROUTE="yes"
| PEERDNS="yes"
| PEERROUTES="yes"
| IPV4_FAILURE_FATAL="no"
| IPV6INIT="yes"
| IPV6_AUTOCONF="yes"
| IPV6_DEFROUTE="yes"
| IPV6_PEERDNS="yes"
| IPV6_PEERROUTES="yes"
| IPV6_FAILURE_FATAL="no"
| NAME="enp0s3"
| UUID="32bad876-680a-4f78-a364-726eae21bfcf"
| DEVICE="enp0s3"
| ONBOOT="yes"
| # /etc/sysconfig/network-scripts/ifcfg-enp0s8
| # Network interface enp0s8 is IPv6 internal interface to provide IPv6 to internal hosts
| BOOTPROTO=static
| IPV6INIT=yes
| IPV6ADDR="2001:db8:0:2::1/64"
| NAME=enp0s8
| UUID=e931a806-2f76-425d-b035-d37813b81df5
| DEVICE=enp0s8
| ONBOOT=yes
| NM_CONTROLLED=no
| # Disable NetworkManager
| systemctl disable NetworkManager
| # Install dhcp.x86_64, dhcp-common.x86_64, radvd.x86_64 if not already installed
| yum install dhcp-common
| yum install dhcp
| yum install radvd
| # /etc/sysctl.conf Set sysctl to enable IPv6 forwarding
| net.ipv6.conf.all.forwarding=1
| net.ipv6.conf.enp0s3.accept_ra=2
| net.ipv6.conf.enp0s3.accept_ra_defrtr=1
| net.ipv6.conf.enp0s3.router_solicitations=1
| # /etc/radvd.conf
| interface enp0s8
| {
| # This is the primary "on switch" for RADVD
| AdvSendAdvert on;
| #
| # These settings determine how often advertisements will be sent every X-Y.
| # X and Y are in seconds.
| # With these settings you will be sending a advert every 60 seconds
| #
| MinRtrAdvInterval 60;
| MaxRtrAdvInterval 180;
| #
| # Disable Mobile IPv6 support
| #
| AdvHomeAgentFlag off;
| #
| # Here we set our managed flags
| #
| AdvManagedFlag on;
| AdvOtherConfigFlag on;
| #
| # Enter our IPv6 prefix and CIDR
| #
| prefix 2001:db8:0:2::/64
| {
| AdvOnLink on;
| # On link tells the host that the default router is on the same "link" as it is
| AdvAutonomous on;
| AdvRouterAddr off;
| };
| };
# Enable radvd service
systemctl enable radvd
# In /etc/sysconfig/network add
IPV6FORWARDING=yes
=================================================================
Set up a Service VM Running as a vRouter (DHCPv6 Stateful Server)
=================================================================
| # Current network setup for IPv6 router VM on local virtualbox setup
| # /etc/sysconfig/network-scripts/ifcfg-enp0s3
| # Network interface enp0s3 is IPv4 for public internet access
| TYPE="Ethernet"
| BOOTPROTO="dhcp"
| DEFROUTE="yes"
| PEERDNS="yes"
| PEERROUTES="yes"
| IPV4_FAILURE_FATAL="no"
| IPV6INIT="yes"
| IPV6_AUTOCONF="yes"
| IPV6_DEFROUTE="yes"
| IPV6_PEERDNS="yes"
| IPV6_PEERROUTES="yes"
| IPV6_FAILURE_FATAL="no"
| NAME="enp0s3"
| UUID="32bad876-680a-4f78-a364-726eae21bfcf"
| DEVICE="enp0s3"
| ONBOOT="yes"
| # /etc/sysconfig/network-scripts/ifcfg-enp0s8
| # Network interface enp0s8 is IPv6 internal interface to provide IPv6 to internal hosts
| BOOTPROTO=static
| IPV6INIT=yes
| IPV6ADDR="2001:db8:0:2::1/64"
| NAME=enp0s8
| UUID=e931a806-2f76-425d-b035-d37813b81df5
| DEVICE=enp0s8
| ONBOOT=yes
| NM_CONTROLLED=no
| # Disable NetworkManager
| systemctl disable NetworkManager
| # Install dhcp.x86_64, dhcp-common.x86_64, radvd.x86_64 if not already installed
| yum install dhcp-common
| yum install dhcp
| yum install radvd
| # /etc/sysctl.conf Set sysctl to enable IPv6 forwarding
| net.ipv6.conf.all.forwarding=1
| net.ipv6.conf.enp0s3.accept_ra=2
| net.ipv6.conf.enp0s3.accept_ra_defrtr=1
| net.ipv6.conf.enp0s3.router_solicitations=1
| # /etc/dhcp/dhcpd6.conf
| # DHCP for IPv6 Server Configuration file.
| # Enable RFC 5007 support (same than for DHCPv4)
allow leasequery;
| # IPv6 address valid lifetime
| # (at the end the address is no longer usable by the client)
| # (set to 30 days, the usual IPv6 default)
| default-lease-time 2592000;
| # IPv6 address preferred lifetime
| # (at the end the address is deprecated, i.e., the client should use
| # other addresses for new connections)
| # (set to 7 days, the usual IPv6 default)
| preferred-lifetime 604800;
| # T1, the delay before Renew
| # (default is 1/2 preferred lifetime)
| # (set to 1 hour)
| option dhcp-renewal-time 3600;
| # T2, the delay before Rebind (if Renews failed)
| # (default is 3/4 preferred lifetime)
| # (set to 2 hours)
| option dhcp-rebinding-time 7200;
| # The path of the lease file
| dhcpv6-lease-file-name "/var/lib/dhcpd/dhcpd6.leases";
| # Set preference to 255 (maximum) in order to avoid waiting for
| # additional servers when there is only one
| option dhcp6.preference 255;
| # Server side command to enable rapid-commit (2 packet exchange)
| option dhcp6.rapid-commit;
| # The delay before information-request refresh
| # (minimum is 10 minutes, maximum one day, default is to not refresh)
| # (set to 6 hours)
option dhcp6.info-refresh-time 21600;
| # Set this to `interim` when doing ddns updates
| ddns-update-style interim;
|
| subnet6 2001:db8:0:2::/64 {
| option dhcp6.name-servers 2001:db8:0:2::1;
| option dhcp6.domain-search "opnfv.local";
| ddns-hostname = concat(binary-to-ascii(10, 8, "-", leased-address), ".wired");
| ddns-domainname = "opnfv.local";
| # Our address range 1000 through 1fff
| range6 2001:db8:0:2::1000 2001:db8:0:2::1fff;
| }
|
| # In /etc/sysconfig/network add
| IPV6FORWARDING=yes
For reference, refer to `How to set up RADVd DHCPv6 and DNS on CentOS 6`_.
.. _`How to set up RADVd DHCPv6 and DNS on CentOS 6`: http://www.percula.info/archives/196
|
