1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
|
======================================================================
Set Up a Service VM as an IPv6 vRouter in Native OpenStack Environment
======================================================================
If you intend to set up a service VM as an IPv6 vRouter in native OpenStack environment of
OPNFV Brahmaputra Release base platform, the instructions are as follows.
Please **NOTE** that:
* Because the anti-spoofing rules of Security Group feature in OpenStack prevents
a VM from forwarding packets, we need to disable Security Group feature in the
native OpenStack environment.
* The hostnames, IP addresses, and username are for exemplary purpose in instructions.
Please change as needed to fit your environment.
* The instructions apply to both deployment model of single controller node and
HA (High Availability) deployment model where multiple controller nodes are used
*****************************
Install OPNFV and Preparation
*****************************
**OPNFV-NATIVE-INSTALL-1**: To install pure OpenStack option of OPNFV Brahmaputra Release:
.. code-block:: bash
deploy --scenario os_ha
**OPNFV-NATIVE-INSTALL-2**: Clone the following GitHub repository to get the
configuration and metadata files
.. code-block:: bash
git clone https://github.com/sridhargaddam/opnfv_os_ipv6_poc.git /opt/stack/opnfv_os_ipv6_poc
**********************************************
Disable Security Groups in OpenStack ML2 Setup
**********************************************
**OPNFV-NATIVE-SEC-1**: Change the settings in
``/etc/neutron/plugins/ml2/ml2_conf.ini`` as follows
.. code-block:: bash
# /etc/neutron/plugins/ml2/ml2_conf.ini
[securitygroup]
enable_security_group = False
firewall_driver = neutron.agent.firewall.NoopFirewallDriver
**OPNFV-NATIVE-SEC-2**: Change the settings in ``/etc/nova/nova.conf`` as follows
.. code-block:: bash
# /etc/nova/nova.conf
[DEFAULT]
security_group_api = nova
firewall_driver = nova.virt.firewall.NoopFirewallDriver
*********************************
Set Up Service VM as IPv6 vRouter
*********************************
**OPNFV-NATIVE-SETUP-1**: Now we assume that OpenStack multi-node setup is up and running. The following
commands should be executed:
.. code-block:: bash
source openrc admin demo
**OPNFV-NATIVE-SETUP-2**: Download ``fedora22`` image which would be used for ``vRouter``
.. code-block:: bash
wget https://download.fedoraproject.org/pub/fedora/linux/releases/22/Cloud/x86_64/Images/Fedora-Cloud-Base-22-20150521.x86_64.qcow2
**OPNFV-NATIVE-SETUP-3**: Import Fedora22 image to ``glance``
.. code-block:: bash
glance image-create --name 'Fedora22' --disk-format qcow2 --container-format bare --file ./Fedora-Cloud-Base-22-20150521.x86_64.qcow2
**OPNFV-NATIVE-SETUP-4**: Create Neutron routers ``ipv4-router`` and ``ipv6-router``
which need to provide external connectivity.
.. code-block:: bash
neutron router-create ipv4-router
neutron router-create ipv6-router
**OPNFV-NATIVE-SETUP-5**: Create an external network/subnet ``ext-net`` using
the appropriate values based on the data-center physical network setup.
.. code-block:: bash
neutron net-create --router:external ext-net
**OPNFV-NATIVE-SETUP-6**: If your ``opnfv-os-controller`` node has two interfaces ``eth0`` and
``eth1``, and ``eth1`` is used for external connectivity, move the IP address of ``eth1`` to ``br-ex``.
Please note that the IP address ``198.59.156.113`` and related subnet and gateway addressed in the command
below are for exemplary purpose. **Please replace them with the IP addresses of your actual network**.
.. code-block:: bash
sudo ip addr del 198.59.156.113/24 dev eth1
sudo ovs-vsctl add-port br-ex eth1
sudo ifconfig eth1 up
sudo ip addr add 198.59.156.113/24 dev br-ex
sudo ifconfig br-ex up
sudo ip route add default via 198.59.156.1 dev br-ex
neutron subnet-create --disable-dhcp --allocation-pool start=198.59.156.251,end=198.59.156.254 --gateway 198.59.156.1 ext-net 198.59.156.0/24
**OPNFV-NATIVE-SETUP-7**: Verify that ``br-ex`` now has the original external IP address,
and that the default route is on ``br-ex``
.. code-block:: bash
$ ip a s br-ex
38: br-ex: <BROADCAST,UP,LOWER_UP> mtu 1430 qdisc noqueue state UNKNOWN group default
link/ether 00:50:56:82:42:d1 brd ff:ff:ff:ff:ff:ff
inet 198.59.156.113/24 brd 198.59.156.255 scope global br-ex
valid_lft forever preferred_lft forever
inet6 fe80::543e:28ff:fe70:4426/64 scope link
valid_lft forever preferred_lft forever
$
$ ip route
default via 198.59.156.1 dev br-ex
192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.10
192.168.122.0/24 dev virbr0 proto kernel scope link src 192.168.122.1
198.59.156.0/24 dev br-ex proto kernel scope link src 198.59.156.113
Please note that the IP addresses above are exemplary purpose.
**OPNFV-NATIVE-SETUP-8**: Create Neutron networks ``ipv4-int-network1`` and
``ipv6-int-network2`` with port_security disabled
.. code-block:: bash
neutron net-create --port_security_enabled=False ipv4-int-network1
neutron net-create --port_security_enabled=False ipv6-int-network2
**OPNFV-NATIVE-SETUP-9**: Create IPv4 subnet ``ipv4-int-subnet1`` in the internal network
``ipv4-int-network1``, and associate it to ``ipv4-router``.
.. code-block:: bash
neutron subnet-create --name ipv4-int-subnet1 --dns-nameserver 8.8.8.8 ipv4-int-network1 20.0.0.0/24
neutron router-interface-add ipv4-router ipv4-int-subnet1
**OPNFV-NATIVE-SETUP-10**: Associate the ``ext-net`` to the Neutron routers ``ipv4-router``
and ``ipv6-router``.
.. code-block:: bash
neutron router-gateway-set ipv4-router ext-net
neutron router-gateway-set ipv6-router ext-net
**OPNFV-NATIVE-SETUP-11**: Create two subnets, one IPv4 subnet ``ipv4-int-subnet2`` and
one IPv6 subnet ``ipv6-int-subnet2`` in ``ipv6-int-network2``, and associate both subnets to
``ipv6-router``
.. code-block:: bash
neutron subnet-create --name ipv4-int-subnet2 --dns-nameserver 8.8.8.8 ipv6-int-network2 10.0.0.0/24
neutron subnet-create --name ipv6-int-subnet2 --ip-version 6 --ipv6-ra-mode slaac --ipv6-address-mode slaac ipv6-int-network2 2001:db8:0:1::/64
neutron router-interface-add ipv6-router ipv4-int-subnet2
neutron router-interface-add ipv6-router ipv6-int-subnet2
**OPNFV-NATIVE-SETUP-12**: Create a keypair
.. code-block:: bash
nova keypair-add vRouterKey > ~/vRouterKey
**OPNFV-NATIVE-SETUP-13**: Create ports for vRouter (with some specific MAC address
- basically for automation - to know the IPv6 addresses that would be assigned to the port).
.. code-block:: bash
neutron port-create --name eth0-vRouter --mac-address fa:16:3e:11:11:11 ipv6-int-network2
neutron port-create --name eth1-vRouter --mac-address fa:16:3e:22:22:22 ipv4-int-network1
**OPNFV-NATIVE-SETUP-14**: Create ports for VM1 and VM2.
.. code-block:: bash
neutron port-create --name eth0-VM1 --mac-address fa:16:3e:33:33:33 ipv4-int-network1
neutron port-create --name eth0-VM2 --mac-address fa:16:3e:44:44:44 ipv4-int-network1
**OPNFV-NATIVE-SETUP-15**: Update ``ipv6-router`` with routing information to subnet
``2001:db8:0:2::/64``
.. code-block:: bash
neutron router-update ipv6-router --routes type=dict list=true destination=2001:db8:0:2::/64,nexthop=2001:db8:0:1:f816:3eff:fe11:1111
**OPNFV-NATIVE-SETUP-16**: Boot Service VM (``vRouter``), VM1 and VM2
.. code-block:: bash
nova boot --image Fedora22 --flavor m1.small --user-data /opt/stack/opnfv_os_ipv6_poc/metadata.txt --availability-zone nova:opnfv-os-compute --nic port-id=$(neutron port-list | grep -w eth0-vRouter | awk '{print $2}') --nic port-id=$(neutron port-list | grep -w eth1-vRouter | awk '{print $2}') --key-name vRouterKey vRouter
nova list
nova console-log vRouter #Please wait for some 10 to 15 minutes so that necessary packages (like radvd) are installed and vRouter is up.
nova boot --image cirros-0.3.4-x86_64-uec --flavor m1.tiny --nic port-id=$(neutron port-list | grep -w eth0-VM1 | awk '{print $2}') --availability-zone nova:opnfv-os-controller --key-name vRouterKey --user-data /opt/stack/opnfv_os_ipv6_poc/set_mtu.sh VM1
nova boot --image cirros-0.3.4-x86_64-uec --flavor m1.tiny --nic port-id=$(neutron port-list | grep -w eth0-VM2 | awk '{print $2}') --availability-zone nova:opnfv-os-compute --key-name vRouterKey --user-data /opt/stack/opnfv_os_ipv6_poc/set_mtu.sh VM2
nova list # Verify that all the VMs are in ACTIVE state.
**OPNFV-NATIVE-SETUP-17**: If all goes well, the IPv6 addresses assigned to the VMs
would be as shown as follows:
.. code-block:: bash
vRouter eth0 interface would have the following IPv6 address: 2001:db8:0:1:f816:3eff:fe11:1111/64
vRouter eth1 interface would have the following IPv6 address: 2001:db8:0:2::1/64
VM1 would have the following IPv6 address: 2001:db8:0:2:f816:3eff:fe33:3333/64
VM2 would have the following IPv6 address: 2001:db8:0:2:f816:3eff:fe44:4444/64
**OPNFV-NATIVE-SETUP-18**: To ``SSH`` to vRouter, you can execute the following command.
.. code-block:: bash
sudo ip netns exec qrouter-$(neutron router-list | grep -w ipv6-router | awk '{print $2}') ssh -i ~/vRouterKey fedora@2001:db8:0:1:f816:3eff:fe11:1111
|
