diff options
| -rw-r--r-- | docs/release/configguide/featureconfig.rst | 584 | ||||
| -rw-r--r-- | docs/release/configguide/index.rst | 2 | ||||
| -rw-r--r-- | docs/release/configguide/postinstall.rst | 6 | ||||
| -rw-r--r-- | docs/release/installation/index.rst | 2 | ||||
| -rw-r--r-- | docs/release/installation/installation.instruction.rst | 5 | ||||
| -rw-r--r-- | docs/release/release-notes/release-notes.rst | 16 |
6 files changed, 24 insertions, 591 deletions
diff --git a/docs/release/configguide/featureconfig.rst b/docs/release/configguide/featureconfig.rst index b364580..3e3d99b 100644 --- a/docs/release/configguide/featureconfig.rst +++ b/docs/release/configguide/featureconfig.rst @@ -6,18 +6,17 @@ IPv6 Configuration - Setting Up a Service VM as an IPv6 vRouter =============================================================== -This section provides instructions to set up a service VM as an IPv6 vRouter using OPNFV Danube Release -installers. The environment may be pure OpenStack option or Open Daylight L2-only option. -The deployment model may be HA or non-HA. The infrastructure may be bare metal or virtual environment. +This section provides instructions to set up a service VM as an IPv6 vRouter using OPNFV Euphrates Release +installers. Because Open Daylight no longer supports L2-only option, and there is only limited support of +IPv6 in L3 option of Open Daylight, setup of service VM as an IPv6 vRouter is only available under +pure/native OpenStack environment. The deployment model may be HA or non-HA. The infrastructure may be +bare metal or virtual environment. **************************** Pre-configuration Activities **************************** -The configuration will work in 2 environments: - -1. OpenStack-only environment -2. OpenStack with Open Daylight L2-only environment +The configuration will work only in OpenStack-only environment. Depending on which installer will be used to deploy OPNFV, each environment may be deployed on bare metal or virtualized infrastructure. Each deployment may be HA or non-HA. @@ -29,7 +28,7 @@ Setup Manual in OpenStack-Only Environment ****************************************** If you intend to set up a service VM as an IPv6 vRouter in OpenStack-only environment of -OPNFV Danube Release, please **NOTE** that: +OPNFV Euphrates Release, please **NOTE** that: * Because the anti-spoofing rules of Security Group feature in OpenStack prevents a VM from forwarding packets, we need to disable Security Group feature in the @@ -43,7 +42,7 @@ OPNFV Danube Release, please **NOTE** that: Install OPNFV and Preparation ----------------------------- -**OPNFV-NATIVE-INSTALL-1**: To install OpenStack-only environment of OPNFV Danube Release: +**OPNFV-NATIVE-INSTALL-1**: To install OpenStack-only environment of OPNFV Euphrates Release: **Apex Installer**: @@ -116,7 +115,7 @@ Install OPNFV and Preparation # 4.1 Example of <lab-name>: -l devel-pipeline # 4.2 Example of <pod-name>: -p elx # 5. <iso-uri> could be local or remote ISO image of Fuel Installer - # 5.1 Example: http://artifacts.opnfv.org/fuel/danube/opnfv-danube.1.0.iso + # 5.1 Example: http://artifacts.opnfv.org/fuel/euphrates/opnfv-euphrates.1.0.iso # # Please refer to Fuel Installer's documentation for further information and any update @@ -450,577 +449,16 @@ would be as shown as follows: ssh -i ~/vRouterKey cirros@<floating-ip-of-VM1> ssh -i ~/vRouterKey cirros@<floating-ip-of-VM2> -**************************************************************** -Setup Manual in OpenStack with Open Daylight L2-Only Environment -**************************************************************** - -If you intend to set up a service VM as an IPv6 vRouter in an environment of OpenStack -and Open Daylight L2-only of OPNFV Danube Release, please **NOTE** that: - -* We **SHOULD** use the ``odl-ovsdb-openstack`` version of Open Daylight Boron - in OPNFV Danube Release. Please refer to our - `Gap Analysis <http://artifacts.opnfv.org/ipv6/docs/release_userguide/index.html#ipv6-gap-analysis-with-open-daylight-boron>`_ - for more information. -* The hostnames, IP addresses, and username are for exemplary purpose in instructions. - Please change as needed to fit your environment. -* The instructions apply to both deployment model of single controller node and - HA (High Availability) deployment model where multiple controller nodes are used. -* However, in case of HA, when ``ipv6-router`` is created in step **SETUP-SVM-11**, - it could be created in any of the controller node. Thus you need to identify in which - controller node ``ipv6-router`` is created in order to manually spawn ``radvd`` daemon - inside the ``ipv6-router`` namespace in steps **SETUP-SVM-24** through **SETUP-SVM-30**. - ------------------------------ -Install OPNFV and Preparation ------------------------------ - -**OPNFV-INSTALL-1**: To install OpenStack with Open Daylight L2-only environment -of OPNFV Danube Release: - -**Apex Installer**: - -Please **NOTE** that: - -* In OPNFV Danube Release, Apex Installer no longer supports Open Daylight - L2-only environment or ``odl-ovsdb-openstack``. Instead, it supports Open - Daylight L3 deployment with ``odl-netvirt-openstack``. -* IPv6 features are not fully supported in Open Daylight L3 with - ``odl-netvirt-openstack`` yet. It is still a work in progress. -* Thus we cannot realize Service VM as an IPv6 vRouter using Apex Installer - under OpenStack + Open Daylight L3 with ``odl-netvirt-openstack`` environment. - -**Compass** Installer: - -.. code-block:: bash - - # HA deployment in OpenStack with Open Daylight L2-only environment - export ISO_URL=file://$BUILD_DIRECTORY/compass.iso - export OS_VERSION=${{COMPASS_OS_VERSION}} - export OPENSTACK_VERSION=${{COMPASS_OPENSTACK_VERSION}} - export CONFDIR=$WORKSPACE/deploy/conf/vm_environment - ./deploy.sh --dha $CONFDIR/os-odl_l2-nofeature-ha.yml \ - --network $CONFDIR/$NODE_NAME/network.yml - - # Non-HA deployment in OpenStack with Open Daylight L2-only environment - # Non-HA deployment is currently not supported by Compass installer - -**Fuel** Installer: - -.. code-block:: bash - - # HA deployment in OpenStack with Open Daylight L2-only environment - # Scenario Name: os-odl_l2-nofeature-ha - # Scenario Configuration File: ha_odl-l2_heat_ceilometer_scenario.yaml - # You can use either Scenario Name or Scenario Configuration File Name in "-s" parameter - sudo ./deploy.sh -b <stack-config-uri> -l <lab-name> -p <pod-name> \ - -s os-odl_l2-nofeature-ha -i <iso-uri> - - # Non-HA deployment in OpenStack with Open Daylight L2-only environment - # Scenario Name: os-odl_l2-nofeature-noha - # Scenario Configuration File: no-ha_odl-l2_heat_ceilometer_scenario.yaml - # You can use either Scenario Name or Scenario Configuration File Name in "-s" parameter - sudo ./deploy.sh -b <stack-config-uri> -l <lab-name> -p <pod-name> \ - -s os-odl_l2-nofeature-noha -i <iso-uri> - - # Note: - # - # 1. Refer to http://git.opnfv.org/cgit/fuel/tree/deploy/scenario/scenario.yaml for scenarios - # 2. Refer to http://git.opnfv.org/cgit/fuel/tree/ci/README for description of - # stack configuration directory structure - # 3. <stack-config-uri> is the base URI of stack configuration directory structure - # 3.1 Example: http://git.opnfv.org/cgit/fuel/tree/deploy/config - # 4. <lab-name> and <pod-name> must match the directory structure in stack configuration - # 4.1 Example of <lab-name>: -l devel-pipeline - # 4.2 Example of <pod-name>: -p elx - # 5. <iso-uri> could be local or remote ISO image of Fuel Installer - # 5.1 Example: http://artifacts.opnfv.org/fuel/danube/opnfv-danube.1.0.iso - # - # Please refer to Fuel Installer's documentation for further information and any update - -**Joid** Installer: - -.. code-block:: bash - - # HA deployment in OpenStack with Open Daylight L2-only environment - ./deploy.sh -o mitaka -s odl -t ha -l default -f ipv6 - - # Non-HA deployment in OpenStack with Open Daylight L2-only environment - ./deploy.sh -o mitaka -s odl -t nonha -l default -f ipv6 - -Please **NOTE** that: - -* You need to refer to **installer's documentation** for other necessary - parameters applicable to your deployment. -* You need to refer to **Release Notes** and **installer's documentation** if there is - any issue in installation. - -**OPNFV-INSTALL-2**: Clone the following GitHub repository to get the -configuration and metadata files - -.. code-block:: bash - - git clone https://github.com/sridhargaddam/opnfv_os_ipv6_poc.git \ - /opt/stack/opnfv_os_ipv6_poc - ----------------------------------------------- -Disable Security Groups in OpenStack ML2 Setup ----------------------------------------------- - -Please **NOTE** that although Security Groups feature has been disabled automatically -through ``local.conf`` configuration file by some installers such as ``devstack``, it is very likely -that other installers such as ``Apex``, ``Compass``, ``Fuel`` or ``Joid`` will enable Security -Groups feature after installation. - -**Please make sure that Security Groups are disabled in the setup** - -In order to disable Security Groups globally, please make sure that the settings in -**OPNFV-SEC-1** and **OPNFV-SEC-2** are applied, if they are not there by default. - -**OPNFV-SEC-1**: Change the settings in -``/etc/neutron/plugins/ml2/ml2_conf.ini`` as follows, if they -are not there by default. - -.. code-block:: bash - - # /etc/neutron/plugins/ml2/ml2_conf.ini - [securitygroup] - enable_security_group = True - firewall_driver = neutron.agent.firewall.NoopFirewallDriver - [ml2] - extension_drivers = port_security - [agent] - prevent_arp_spoofing = False - -**OPNFV-SEC-2**: Change the settings in ``/etc/nova/nova.conf`` as follows, -if they are not there by default. - -.. code-block:: bash - - # /etc/nova/nova.conf - [DEFAULT] - security_group_api = neutron - firewall_driver = nova.virt.firewall.NoopFirewallDriver - -**OPNFV-SEC-3**: After updating the settings, you will have to restart the -``Neutron`` and ``Nova`` services. - -**Please note that the commands of restarting** ``Neutron`` **and** ``Nova`` **would vary -depending on the installer. Please refer to relevant documentation of specific installers** - ---------------------------------------------------- -Source the Credentials in OpenStack Controller Node ---------------------------------------------------- - -**SETUP-SVM-1**: Login in OpenStack Controller Node. Start a new terminal, -and change directory to where OpenStack is installed. - -**SETUP-SVM-2**: We have to source the tenant credentials in this step. Please **NOTE** -that the method of sourcing tenant credentials may vary depending on installers. For example: - -**Apex** installer: - -.. code-block:: bash - - # On jump host, source the tenant credentials using /bin/opnfv-util provided by Apex installer - opnfv-util undercloud "source overcloudrc; keystone service-list" - - # Alternatively, you can copy the file /home/stack/overcloudrc from the installer VM called "undercloud" - # to a location in controller node, for example, in the directory /opt, and do: - # source /opt/overcloudrc - -**Compass** installer: - -.. code-block:: bash - - # source the tenant credentials using Compass installer of OPNFV - source /opt/admin-openrc.sh - -**Fuel** installer: - -.. code-block:: bash - - # source the tenant credentials using Fuel installer of OPNFV - source /root/openrc - -**Joid** installer: - -.. code-block:: bash - - # source the tenant credentials using Joid installer of OPNFV - source $HOME/joid_config/admin-openrc - -**devstack**: - -.. code-block:: bash - - # source the tenant credentials in devstack - source openrc admin demo - -**Please refer to relevant documentation of installers if you encounter any issue**. - ------------------------------------------------------------------------------------- -Informational Note: Move Public Network from Physical Network Interface to ``br-ex`` ------------------------------------------------------------------------------------- - -**SETUP-SVM-3**: Move the physical interface (i.e. the public network interface) to ``br-ex`` - -**SETUP-SVM-4**: Verify setup of ``br-ex`` - -**Those 2 steps are Informational. OPNFV Installer has taken care of those 2 steps during deployment. -You may refer to this step only if there is any issue, or if you are using other installers**. - -We have to move the physical interface (i.e. the public network interface) to ``br-ex``, including moving -the public IP address and setting up default route. Please refer to ``SETUP-SVM-3`` and -``SETUP-SVM-4`` in our `more complete instruction <http://artifacts.opnfv.org/ipv6/docs/setupservicevm/4-ipv6-configguide-servicevm.html#add-external-connectivity-to-br-ex>`_. - --------------------------------------------------------- -Create IPv4 Subnet and Router with External Connectivity --------------------------------------------------------- - -**SETUP-SVM-5**: Create a Neutron router ``ipv4-router`` which needs to provide external connectivity. - -.. code-block:: bash - - neutron router-create ipv4-router - -**SETUP-SVM-6**: Create an external network/subnet ``ext-net`` using the appropriate values based on the -data-center physical network setup. - -Please **NOTE** that you may only need to create the subnet of ``ext-net`` because OPNFV installers -should have created an external network during installation. You must use the same name of external -network that installer creates when you create the subnet. For example: - -* **Apex** installer: ``external`` -* **Compass** installer: ``ext-net`` -* **Fuel** installer: ``admin_floating_net`` -* **Joid** installer: ``ext-net`` - -**Please refer to the documentation of installers if there is any issue** - -.. code-block:: bash - - # This is needed only if installer does not create an external work - # Otherwise, skip this command "net-create" - neutron net-create --router:external ext-net - - # Note that the name "ext-net" may work for some installers such as Compass and Joid - # Change the name "ext-net" to match the name of external network that an installer creates - neutron subnet-create --disable-dhcp --allocation-pool start=198.59.156.251,\ - end=198.59.156.254 --gateway 198.59.156.1 ext-net 198.59.156.0/24 - -Please note that the IP addresses in the command above are for exemplary purpose. **Please replace the IP addresses of -your actual network**. - -**SETUP-SVM-7**: Associate the ``ext-net`` to the Neutron router ``ipv4-router``. - -.. code-block:: bash - - # Note that the name "ext-net" may work for some installers such as Compass and Joid - # Change the name "ext-net" to match the name of external network that an installer creates - neutron router-gateway-set ipv4-router ext-net - -**SETUP-SVM-8**: Create an internal/tenant IPv4 network ``ipv4-int-network1`` - -.. code-block:: bash - - neutron net-create ipv4-int-network1 - -**SETUP-SVM-9**: Create an IPv4 subnet ``ipv4-int-subnet1`` in the internal network ``ipv4-int-network1`` - -.. code-block:: bash - - neutron subnet-create --name ipv4-int-subnet1 --dns-nameserver 8.8.8.8 \ - ipv4-int-network1 20.0.0.0/24 - -**SETUP-SVM-10**: Associate the IPv4 internal subnet ``ipv4-int-subnet1`` to the Neutron router ``ipv4-router``. - -.. code-block:: bash - - neutron router-interface-add ipv4-router ipv4-int-subnet1 - --------------------------------------------------------- -Create IPv6 Subnet and Router with External Connectivity --------------------------------------------------------- - -Now, let us create a second neutron router where we can "manually" spawn a ``radvd`` daemon to simulate an external -IPv6 router. - -**SETUP-SVM-11**: Create a second Neutron router ``ipv6-router`` which needs to provide external connectivity - -.. code-block:: bash - - neutron router-create ipv6-router - -**SETUP-SVM-12**: Associate the ``ext-net`` to the Neutron router ``ipv6-router`` - -.. code-block:: bash - - # Note that the name "ext-net" may work for some installers such as Compass and Joid - # Change the name "ext-net" to match the name of external network that an installer creates - neutron router-gateway-set ipv6-router ext-net - -**SETUP-SVM-13**: Create a second internal/tenant IPv4 network ``ipv4-int-network2`` - -.. code-block:: bash - - neutron net-create ipv4-int-network2 - -**SETUP-SVM-14**: Create an IPv4 subnet ``ipv4-int-subnet2`` for the ``ipv6-router`` internal network -``ipv4-int-network2`` - -.. code-block:: bash - - neutron subnet-create --name ipv4-int-subnet2 --dns-nameserver 8.8.8.8 \ - ipv4-int-network2 10.0.0.0/24 - -**SETUP-SVM-15**: Associate the IPv4 internal subnet ``ipv4-int-subnet2`` to the Neutron router ``ipv6-router``. - -.. code-block:: bash - - neutron router-interface-add ipv6-router ipv4-int-subnet2 - --------------------------------------------------- -Prepare Image, Metadata and Keypair for Service VM --------------------------------------------------- - -**SETUP-SVM-16**: Download ``fedora22`` image which would be used as ``vRouter`` - -.. code-block:: bash - - wget https://download.fedoraproject.org/pub/fedora/linux/releases/22/Cloud/x86_64/\ - Images/Fedora-Cloud-Base-22-20150521.x86_64.qcow2 - - glance image-create --name 'Fedora22' --disk-format qcow2 --container-format bare \ - --file ./Fedora-Cloud-Base-22-20150521.x86_64.qcow2 - -**SETUP-SVM-17**: Create a keypair - -.. code-block:: bash - - nova keypair-add vRouterKey > ~/vRouterKey - -**SETUP-SVM-18**: Create ports for ``vRouter`` and both the VMs with some specific MAC addresses. - -.. code-block:: bash - - neutron port-create --name eth0-vRouter --mac-address fa:16:3e:11:11:11 ipv4-int-network2 - neutron port-create --name eth1-vRouter --mac-address fa:16:3e:22:22:22 ipv4-int-network1 - neutron port-create --name eth0-VM1 --mac-address fa:16:3e:33:33:33 ipv4-int-network1 - neutron port-create --name eth0-VM2 --mac-address fa:16:3e:44:44:44 ipv4-int-network1 - ----------------------------------------------------------------------------------------------------------- -Boot Service VM (``vRouter``) with ``eth0`` on ``ipv4-int-network2`` and ``eth1`` on ``ipv4-int-network1`` ----------------------------------------------------------------------------------------------------------- - -Let us boot the service VM (``vRouter``) with ``eth0`` interface on ``ipv4-int-network2`` connecting to ``ipv6-router``, -and ``eth1`` interface on ``ipv4-int-network1`` connecting to ``ipv4-router``. - -**SETUP-SVM-19**: Boot the ``vRouter`` using ``Fedora22`` image on the OpenStack Compute Node with hostname -``opnfv-os-compute`` - -.. code-block:: bash - - nova boot --image Fedora22 --flavor m1.small \ - --user-data /opt/stack/opnfv_os_ipv6_poc/metadata.txt \ - --availability-zone nova:opnfv-os-compute \ - --nic port-id=$(neutron port-list | grep -w eth0-vRouter | awk '{print $2}') \ - --nic port-id=$(neutron port-list | grep -w eth1-vRouter | awk '{print $2}') \ - --key-name vRouterKey vRouter - -Please **note** that ``/opt/stack/opnfv_os_ipv6_poc/metadata.txt`` is used to enable the ``vRouter`` to automatically -spawn a ``radvd``, and - -* Act as an IPv6 vRouter which advertises the RA (Router Advertisements) with prefix - ``2001:db8:0:2::/64`` on its internal interface (``eth1``). -* Forward IPv6 traffic from internal interface (``eth1``) - -**SETUP-SVM-20**: Verify that ``Fedora22`` image boots up successfully and vRouter has ``ssh`` keys properly injected - -.. code-block:: bash - - nova list - nova console-log vRouter - -Please note that **it may take a few minutes** for the necessary packages to get installed and ``ssh`` keys -to be injected. - -.. code-block:: bash - - # Sample Output - [ 762.884523] cloud-init[871]: ec2: ############################################################# - [ 762.909634] cloud-init[871]: ec2: -----BEGIN SSH HOST KEY FINGERPRINTS----- - [ 762.931626] cloud-init[871]: ec2: 2048 e3:dc:3d:4a:bc:b6:b0:77:75:a1:70:a3:d0:2a:47:a9 (RSA) - [ 762.957380] cloud-init[871]: ec2: -----END SSH HOST KEY FINGERPRINTS----- - [ 762.979554] cloud-init[871]: ec2: ############################################################# - -------------------------------------------- -Boot Two Other VMs in ``ipv4-int-network1`` -------------------------------------------- - -In order to verify that the setup is working, let us create two cirros VMs with ``eth1`` interface on the -``ipv4-int-network1``, i.e., connecting to ``vRouter`` ``eth1`` interface for internal network. - -We will have to configure appropriate ``mtu`` on the VMs' interface by taking into account the tunneling -overhead and any physical switch requirements. If so, push the ``mtu`` to the VM either using ``dhcp`` -options or via ``meta-data``. - -**SETUP-SVM-21**: Create VM1 on OpenStack Controller Node with hostname ``opnfv-os-controller`` - -.. code-block:: bash - - nova boot --image cirros-0.3.4-x86_64-uec --flavor m1.tiny \ - --user-data /opt/stack/opnfv_os_ipv6_poc/set_mtu.sh \ - --availability-zone nova:opnfv-os-controller \ - --nic port-id=$(neutron port-list | grep -w eth0-VM1 | awk '{print $2}') \ - --key-name vRouterKey VM1 - -**SETUP-SVM-22**: Create VM2 on OpenStack Compute Node with hostname ``opnfv-os-compute`` - -.. code-block:: bash - - nova boot --image cirros-0.3.4-x86_64-uec --flavor m1.tiny \ - --user-data /opt/stack/opnfv_os_ipv6_poc/set_mtu.sh \ - --availability-zone nova:opnfv-os-compute \ - --nic port-id=$(neutron port-list | grep -w eth0-VM2 | awk '{print $2}') \ - --key-name vRouterKey VM2 - -**SETUP-SVM-23**: Confirm that both the VMs are successfully booted. - -.. code-block:: bash - - nova list - nova console-log VM1 - nova console-log VM2 - ----------------------------------- -Spawn ``RADVD`` in ``ipv6-router`` ----------------------------------- - -Let us manually spawn a ``radvd`` daemon inside ``ipv6-router`` namespace to simulate an external router. -First of all, we will have to identify the ``ipv6-router`` namespace and move to the namespace. - -Please **NOTE** that in case of HA (High Availability) deployment model where multiple controller -nodes are used, ``ipv6-router`` created in step **SETUP-SVM-11** could be in any of the controller -node. Thus you need to identify in which controller node ``ipv6-router`` is created in order to manually -spawn ``radvd`` daemon inside the ``ipv6-router`` namespace in steps **SETUP-SVM-24** through -**SETUP-SVM-30**. The following command in Neutron will display the controller on which the -``ipv6-router`` is spawned. - -.. code-block:: bash - - neutron l3-agent-list-hosting-router ipv6-router - -Then you login to that controller and execute steps **SETUP-SVM-24** -through **SETUP-SVM-30** - -**SETUP-SVM-24**: identify the ``ipv6-router`` namespace and move to the namespace - -.. code-block:: bash - - sudo ip netns exec qrouter-$(neutron router-list | grep -w ipv6-router | \ - awk '{print $2}') bash - -**SETUP-SVM-25**: Upon successful execution of the above command, you will be in the router namespace. -Now let us configure the IPv6 address on the <qr-xxx> interface. - -.. code-block:: bash - - export router_interface=$(ip a s | grep -w "global qr-*" | awk '{print $7}') - ip -6 addr add 2001:db8:0:1::1 dev $router_interface - -**SETUP-SVM-26**: Update the sample file ``/opt/stack/opnfv_os_ipv6_poc/scenario2/radvd.conf`` -with ``$router_interface``. - -.. code-block:: bash - - cp /opt/stack/opnfv_os_ipv6_poc/scenario2/radvd.conf /tmp/radvd.$router_interface.conf - sed -i 's/$router_interface/'$router_interface'/g' /tmp/radvd.$router_interface.conf - -**SETUP-SVM-27**: Spawn a ``radvd`` daemon to simulate an external router. This ``radvd`` daemon advertises an IPv6 -subnet prefix of ``2001:db8:0:1::/64`` using RA (Router Advertisement) on its $router_interface so that ``eth0`` -interface of ``vRouter`` automatically configures an IPv6 SLAAC address. - -.. code-block:: bash - - $radvd -C /tmp/radvd.$router_interface.conf -p /tmp/br-ex.pid.radvd -m syslog - -**SETUP-SVM-28**: Add an IPv6 downstream route pointing to the ``eth0`` interface of vRouter. - -.. code-block:: bash - - ip -6 route add 2001:db8:0:2::/64 via 2001:db8:0:1:f816:3eff:fe11:1111 - -**SETUP-SVM-29**: The routing table should now look similar to something shown below. - -.. code-block:: bash - - ip -6 route show - 2001:db8:0:1::1 dev qr-42968b9e-62 proto kernel metric 256 - 2001:db8:0:1::/64 dev qr-42968b9e-62 proto kernel metric 256 expires 86384sec - 2001:db8:0:2::/64 via 2001:db8:0:1:f816:3eff:fe11:1111 dev qr-42968b9e-62 proto ra metric 1024 expires 29sec - fe80::/64 dev qg-3736e0c7-7c proto kernel metric 256 - fe80::/64 dev qr-42968b9e-62 proto kernel metric 256 - -**SETUP-SVM-30**: If all goes well, the IPv6 addresses assigned to the VMs would be as shown as follows: - -.. code-block:: bash - - # vRouter eth0 interface would have the following IPv6 address: - # 2001:db8:0:1:f816:3eff:fe11:1111/64 - # vRouter eth1 interface would have the following IPv6 address: - # 2001:db8:0:2::1/64 - # VM1 would have the following IPv6 address: - # 2001:db8:0:2:f816:3eff:fe33:3333/64 - # VM2 would have the following IPv6 address: - # 2001:db8:0:2:f816:3eff:fe44:4444/64 - --------------------------------- -Testing to Verify Setup Complete --------------------------------- - -Now, let us ``SSH`` to those VMs, e.g. VM1 and / or VM2 and / or vRouter, to confirm that -it has successfully configured the IPv6 address using ``SLAAC`` with prefix -``2001:db8:0:2::/64`` from ``vRouter``. - -We use ``floatingip`` mechanism to achieve ``SSH``. - -**SETUP-SVM-31**: Now we can ``SSH`` to VMs. You can execute the following command. - -.. code-block:: bash - - # 1. Create a floatingip and associate it with VM1, VM2 and vRouter (to the port id that is passed). - # Note that the name "ext-net" may work for some installers such as Compass and Joid - # Change the name "ext-net" to match the name of external network that an installer creates - neutron floatingip-create --port-id $(neutron port-list | grep -w eth0-VM1 | \ - awk '{print $2}') ext-net - neutron floatingip-create --port-id $(neutron port-list | grep -w eth0-VM2 | \ - awk '{print $2}') ext-net - neutron floatingip-create --port-id $(neutron port-list | grep -w eth1-vRouter | \ - awk '{print $2}') ext-net - - # 2. To know / display the floatingip associated with VM1, VM2 and vRouter. - neutron floatingip-list -F floating_ip_address -F port_id | grep $(neutron port-list | \ - grep -w eth0-VM1 | awk '{print $2}') | awk '{print $2}' - neutron floatingip-list -F floating_ip_address -F port_id | grep $(neutron port-list | \ - grep -w eth0-VM2 | awk '{print $2}') | awk '{print $2}' - neutron floatingip-list -F floating_ip_address -F port_id | grep $(neutron port-list | \ - grep -w eth1-vRouter | awk '{print $2}') | awk '{print $2}' - - # 3. To ssh to the vRouter, VM1 and VM2, user can execute the following command. - ssh -i ~/vRouterKey fedora@<floating-ip-of-vRouter> - ssh -i ~/vRouterKey cirros@<floating-ip-of-VM1> - ssh -i ~/vRouterKey cirros@<floating-ip-of-VM2> - If everything goes well, ``ssh`` will be successful and you will be logged into those VMs. Run some commands to verify that IPv6 addresses are configured on ``eth0`` interface. -**SETUP-SVM-32**: Show an IPv6 address with a prefix of ``2001:db8:0:2::/64`` +**OPNFV-NATIVE-SETUP-19**: Show an IPv6 address with a prefix of ``2001:db8:0:2::/64`` .. code-block:: bash ip address show -**SETUP-SVM-33**: ping some external IPv6 address, e.g. ``ipv6-router`` +**OPNFV-NATIVE-SETUP-20**: ping some external IPv6 address, e.g. ``ipv6-router`` .. code-block:: bash diff --git a/docs/release/configguide/index.rst b/docs/release/configguide/index.rst index 3cceed0..974d49f 100644 --- a/docs/release/configguide/index.rst +++ b/docs/release/configguide/index.rst @@ -11,7 +11,7 @@ IPv6 Configuration Guide :Abstract: This document provides the users with the Configuration Guide to set up a -service VM as an IPv6 vRouter using OPNFV Danube Release. +service VM as an IPv6 vRouter using OPNFV Euphrates Release. .. toctree:: :numbered: diff --git a/docs/release/configguide/postinstall.rst b/docs/release/configguide/postinstall.rst index 9f07ac7..db45f42 100644 --- a/docs/release/configguide/postinstall.rst +++ b/docs/release/configguide/postinstall.rst @@ -10,11 +10,7 @@ Congratulations, you have completed the setup of using a service VM to act as an You have validated the setup based on the instruction in previous sections. If you want to further test your setup, you can ``ping6`` among ``VM1``, ``VM2``, ``vRouter`` and ``ipv6-router``. -This setup allows further open innovation by any 3rd-party. For more instructions and documentations, -please refer to: - -1. IPv6 Configuration Guide (HTML): http://artifacts.opnfv.org/ipv6/docs/setupservicevm/index.html -2. IPv6 User Guide (HTML): http://artifacts.opnfv.org/ipv6/docs/gapanalysis/index.html +This setup allows further open innovation by any 3rd-party. ************************************** Automated post installation activities diff --git a/docs/release/installation/index.rst b/docs/release/installation/index.rst index be42430..cf7e46e 100644 --- a/docs/release/installation/index.rst +++ b/docs/release/installation/index.rst @@ -11,7 +11,7 @@ IPv6 Installation Procedure :Abstract: This document provides the users with the Installation Procedure to install -OPNFV Danube Release on IPv6-only Infrastructure. +OPNFV Euphrates Release on IPv6-only Infrastructure. .. toctree:: :numbered: diff --git a/docs/release/installation/installation.instruction.rst b/docs/release/installation/installation.instruction.rst index ab4d947..c19a5c4 100644 --- a/docs/release/installation/installation.instruction.rst +++ b/docs/release/installation/installation.instruction.rst @@ -12,9 +12,7 @@ except: 1. "admin" network in underlay/undercloud still has to be IPv4, due to lack of support of IPMI over IPv6 or PXE over IPv6. -2. OVS VxLAN (or GRE) tunnel endpoint is still IPv4 only, although IPv6 traffic - can be encapsulated within the tunnel. -3. Metadata server is still IPv4 only. +2. Metadata server is still IPv4 only. Except the limitations above, the use case scenario of the IPv6-only infrastructure includes: @@ -27,6 +25,7 @@ infrastructure includes: 5. Inter VM communication (East-West routing) when VMs are spread across two compute nodes. 6. VNC access into a VM using IPv6 addresses. +7. IPv6 support in OVS VxLAN (and/or GRE) tunnel endpoints with OVS 2.6+ (**NEW**) ------------------------------------------- Install OPNFV in OpenStack-Only Environment diff --git a/docs/release/release-notes/release-notes.rst b/docs/release/release-notes/release-notes.rst index d88ca31..15662e6 100644 --- a/docs/release/release-notes/release-notes.rst +++ b/docs/release/release-notes/release-notes.rst @@ -6,7 +6,7 @@ OPNFV IPv6 Project Release Notes ================================ -This document provides the release notes for Danube of IPv6 Project. +This document provides the release notes for Euphrates of IPv6 Project. .. contents:: :depth: 3 @@ -20,13 +20,13 @@ Version History | **Date** | **Version** | **Author** | **Comment** | | | | | | +--------------------+--------------------+--------------------+--------------------+ -| 2017-02-16 | 0.1.0 | Bin Hu | First draft | +| 2017-09-10 | 0.1.0 | Bin Hu | First draft | | | | | | +--------------------+--------------------+--------------------+--------------------+ -| 2017-03-15 | 0.2.0 | Bin Hu | Baseline draft | +| | 0.x.0 | | Baseline draft | | | | | | +--------------------+--------------------+--------------------+--------------------+ -| 2017-03-21 | 1.0.0 | Bin Hu | Release Ready | +| | 1.0.0 | | Release Ready | | | | | | +--------------------+--------------------+--------------------+--------------------+ @@ -48,12 +48,12 @@ For details, please refer to our `User Guide <../userguide/index.html>`_. Summary ------- -This is the Danube release of the IPv6 feature as part of OPNFV, including: +This is the Euphrates release of the IPv6 feature as part of OPNFV, including: * Installation of OPNFV on IPv6-Only Infrastructure by Apex Installer * Configuration of setting up a Service VM as an IPv6 vRouter -* User Guide, which analyzes the gap of IPv6 support in OpenStack Newton - and OpenDaylight Boron. +* User Guide, which analyzes the gap of IPv6 support in OpenStack Ocata + and OpenDaylight Carbon. Please refer to our: @@ -87,7 +87,7 @@ Please refer to `Testing Methodology <../installation/index.html#testing-methodo References ---------- -For more information on the OPNFV Danube release, please see: +For more information on the OPNFV Euphrates release, please see: http://www.opnfv.org/software |