diff options
Diffstat (limited to 'functest/opnfv_tests/vnf/epc/featureFiles/Auth_NotAccept_by_UE_SQN_failure.feature')
| -rw-r--r-- | functest/opnfv_tests/vnf/epc/featureFiles/Auth_NotAccept_by_UE_SQN_failure.feature | 46 |
1 files changed, 0 insertions, 46 deletions
diff --git a/functest/opnfv_tests/vnf/epc/featureFiles/Auth_NotAccept_by_UE_SQN_failure.feature b/functest/opnfv_tests/vnf/epc/featureFiles/Auth_NotAccept_by_UE_SQN_failure.feature deleted file mode 100644 index ff2a2e20..00000000 --- a/functest/opnfv_tests/vnf/epc/featureFiles/Auth_NotAccept_by_UE_SQN_failure.feature +++ /dev/null @@ -1,46 +0,0 @@ - ############################################################################################################################ - # Date: <13/01/2017> Version: <1.1> # - ############################################################################################################################ - - - Feature:Auth_NotAccept_by_UE_SQN_failure - - @authentication-procedure @Auth_NotAccept_by_UE_SQN_failure @TS_24_301 @24_301_5_4_2_6 @24_301_5_4_2_7 @negTCs @Series-0004 - - Scenario: UE receives an AUTHENTICATION REQUEST message with SQN out of range. UE sends an AUTHENTICATION FAILURE message to the network, with EMM cause "synch failure" and a re-synchronization token. Now UE receives a new correct AUTHENTICATION REQUEST message while T3420 is running. Finally UE sends a correct AUTHENTICATION RESPONSE message. - - Given all configured endpoints for SSH are connected successfully - - Given the steps below will be executed at the end - When I stop S1AP simulator on node ABOT - When I run the SSH command "sudo service mme_gw restart" on node MME - Given that I setup S1AP Simulator with UE parameter "ABOT.UE.CONFIG.SECURITY.SYNC_FAILURE=false" on node ABOT - Given that I setup S1AP Simulator with USIM parameter "ABOT.UE.USIM.AttachWithImsi=true" on node ABOT - Given the execution is paused for {abotprop.WAIT_10_SEC} seconds - Then the ending steps are complete - - # set ABOT configuration - Given that I setup S1AP Simulator with default parameters specified in {abotprop.ABOT.EPC.Defaults} on node ABOT - Given that I setup S1AP Simulator with UE parameter "ABOT.UE.CONFIG.SECURITY.SYNC_FAILURE=true" on node ABOT - Given that I setup S1AP Simulator with USIM parameter "ABOT.UE.USIM.AttachWithImsi=false" on node ABOT - - # Execute ABOT S1AP Simulator - When I run S1AP simulator on node ABOT with 1 UE - - Given the execution is paused for {abotprop.WAIT_10_SEC} seconds - Given the execution is paused for {abotprop.WAIT_10_SEC} seconds - - # Validate Test Case Execution at Simulator - Then I receive S1AP response on node ABOT and verify the presence of all the following values: - | responseResult | existence | - | Send Attach Request message with GUTI | {string:nocase:present} | - | Received Identity Request message | {string:nocase:present} | - | Identification requested type = IMSI | {string:nocase:present} | - | Send Identity Response message | {string:nocase:present} | - | Received Authentication Request message | {string:nocase:present} | - | Send Authentication Failure message (cause=21) | {string:nocase:present} | - | Received Authentication Request message | {string:nocase:present} | - | Send Authentication Response message | {string:nocase:present} | - | Received Security Mode Command message | {string:nocase:present} | - | Send Security Mode Complete message | {string:nocase:present} | - | Received Attach Accept message | {string:nocase:present} | |