diff options
Diffstat (limited to 'docs/configguide/index.rst')
| -rw-r--r-- | docs/configguide/index.rst | 202 |
1 files changed, 82 insertions, 120 deletions
diff --git a/docs/configguide/index.rst b/docs/configguide/index.rst index e4a04330..fc7b25bc 100644 --- a/docs/configguide/index.rst +++ b/docs/configguide/index.rst @@ -1,3 +1,6 @@ +.. This work is licensed under a Creative Commons Attribution 4.0 International License. +.. http://creativecommons.org/licenses/by/4.0 + =============================================== OPNFV FUNCTEST configuration/installation guide =============================================== @@ -9,85 +12,12 @@ OPNFV FUNCTEST configuration/installation guide Introduction ============ -** DOCUMENT IS IN PROGRESS FOR BRAHMAPUTRA ** - This document describes how to install and configure Functest in OPNFV. -Prerequisites -============= - -The OPNFV deployment is out of the scope of this document but it can be found in -XXX. The OPNFV platform is considered as the System Under Test (SUT) in this -document. - -Several prerequisites are needed for functest: - - #. A Jumphost to run Functest on - #. Docker daemon shall be installed on the Jumphost - #. A public/external network created on the SUT - #. Connectivity from the Jumphost to the SUT public/external network - #. Connectivity from the Jumphost to the SUT management network - -NOTE: “Jumphost” refers to any server which meets the previous requirements. -Normally it is the same server from where the OPNFV deployment has been -triggered. - -Docker installation -------------------- - -.. _Ubuntu: https://docs.docker.com/installation/ubuntulinux/ -.. _RHEL: https://docs.docker.com/installation/rhel/ - -Log on your jumphost then install docker (e.g. for Ubuntu):: - - curl -sSL https://get.docker.com/ | sh - -Add your user to docker group to be able to run commands without sudo:: - - sudo usermod -aG docker <your_user> - - -References: - - * Ubuntu_ - * RHEL_ - -Connectivity to OPNFV management network ----------------------------------------- - -Some of the Functest tools need to have access to the OpenStack management -network of the controllers `[1]`_. - -For this reason, an interface shall be configured in the Jumphost in the -OpenStack management network range. - -Example:: - - The OPNFV Fuel installation uses VLAN tagged 300 and subnet 192.168.1.0/24 as - Openstack Management network. - . - Supposing that eth1 is the physical interface with access to that subnet: - $ ip link add name eth1.300 link eth1 type vlan id 300 - $ ip link set eth1.300 up - $ ip addr add 192.168.1.66/24 dev eth1.300 - - -External network on SUT ------------------------ - -Some of the tests against the VIM (Virtual Infrastructure Manager) need an -existing public network to succeed. This is needed, for example, to create -floating IPs to access instances from the public network (i.e. Jumphost). - -By default, any of the four OPNFV installers provide a fresh installation with -an external network created along with a router. - - - High level architecture -======================= +----------------------- -The high level architecture of Functest within OPNFV can be described as follow:: +The high level architecture of Functest within OPNFV can be described as follows:: CIMC/Lights+out management Admin Private Public Storage PXE @@ -152,7 +82,7 @@ All the libraries and dependencies needed by all the Functest tools are pre-installed in the Docker image. This allows running Functest on any platform with any Operating System. -The Docker image will: +The automated mechanisms inside the Functest Docker container will: * retrieve OpenStack credentials * prepare the environment according to the SUT @@ -160,55 +90,98 @@ The Docker image will: * push the results into the OPNFV test result database - This Docker image can be integrated into CI or deployed **independently** of the CI. -A description of the Brahmaputra testcases can be retrieved in the Functest user -guide `[2]`_ Please note that the Functest container has been designed for OPNFV, however, it -would be possible to adapt it to any VIM+controller environment as most of the -testcases are upstream testcases. +would be possible to adapt it to any VIM+controller environment since most of the +test cases are integrated from upstream communities. -.. include:: ./configguide.rst +The test cases are described in the Functest User Guide `[2]`_ + + +Prerequisites +============= + +The OPNFV deployment is out of the scope of this document but it can be found in +`[4]`_. The OPNFV platform is considered as the System Under Test (SUT) in this +document. + +Several prerequisites are needed for Functest: + + #. A Jumphost to run Functest on + #. Docker daemon shall be installed on the Jumphost + #. A public/external network created on the SUT + #. Connectivity from the Jumphost to the SUT public/external network + #. Connectivity from the Jumphost to the SUT management network + +NOTE: “Jumphost” refers to any server which meets the previous requirements. +Normally it is the same server from where the OPNFV deployment has been +triggered. + +Docker installation +------------------- + +.. _Ubuntu: https://docs.docker.com/installation/ubuntulinux/ +.. _RHEL: https://docs.docker.com/installation/rhel/ + +Log on your Jumphost and install docker (e.g. for Ubuntu):: + + curl -sSL https://get.docker.com/ | sh + +Add your user to docker group to be able to run commands without sudo:: + + sudo usermod -aG docker <your_user> -NOTE: This will run ALL the tests by default, see `[2]`_ for details -Focus on the OpenStack credentials ----------------------------------- +References: + + * Ubuntu_ + * RHEL_ + +External network on SUT +----------------------- + +Some of the tests against the VIM (Virtual Infrastructure Manager) need an +existing public network to succeed. This is needed, for example, to create +floating IPs to access instances from the public network (i.e. Jumphost). + +By default, the four OPNFV installers provide a fresh installation with +an external network created along with a router. Make sure that subnet +is reachable from the Jumphost + + +Connectivity to OPNFV management network +---------------------------------------- -The OpenStack credentials are needed to test the VIM. There are 3 ways to -provide them to Functest: +Some of the Functest tools need to have access to the OpenStack management +network of the controllers `[1]`_. + +For this reason, an interface shall be configured in the Jumphost in the +OpenStack management network range. - * using the -v option when running the Docker container - * create an empty file in /home/opnfv/functest/conf/openstack.creds and paste - the needed info in it. - * automatically retrieved using the following script:: - $repos_dir/releng/utils/fetch_os_creds.sh +For example, if the management network is on VLAN 300 and subnet 192.168.1.0/24 +and assuming that eth1 is the physical interface with access to that subnet:: -Once the credentials are there, they shall be sourced before running the tests:: + $ ip link add name eth1.300 link eth1 type vlan id 300 + $ ip link set eth1.300 up + $ ip addr add 192.168.1.66/24 dev eth1.300 - source /home/opnfv/functest/conf/openstack.creds +This is just an example about how to configure an interface with vlan, but it might +defer depending on the deployment settings on each installer. Check the +corresponding installer instructions for more info. -Additional Options ------------------- -In case you need to provide different configuration parameters to Functest (e.g. - commit IDs or branches for the repositories, ...) copy the config_functest.yaml - from the repository to your current directory and run docker with a volume:: +Installation and configuration +============================== - $ wget https://git.opnfv.org/cgit/functest/plain/testcases/config_functest.yaml - $ cmd1 = "/home/opnfv/repos/functest/docker/prepare_env.sh" - $ cmd2 = "/home/opnfv/repos/functest/docker/run_tests.sh" - $ docker run -t -e "INSTALLER_TYPE=fuel" -e "INSTALLER_IP=10.20.0.2" opnfv/functest \ - -v $(pwd)/config_functest.yaml:/home/opnfv/functest/conf/config_functest.yaml \ - "${cmd1} && ${cmd2}" +.. include:: ./configguide.rst Integration in CI ================= -In CI we use the docker file and execute commande within the container from -Jenkins. +In CI we use the Docker image and execute the appropriate commands within the +container from Jenkins. Docker creation in set-functest-env builder `[3]`_:: @@ -269,24 +242,13 @@ Docker clean in functest-cleanup builder `[3]`_:: fi -Configuration -============= - -Everything is preconfigured in the docker file. -It is however possible to customize the list of tests, see `[2]` for details. - -Errors -====== - - - - References ========== .. _`[1]`: https://ask.openstack.org/en/question/68144/keystone-unable-to-use-the-public-endpoint/ -.. _`[2]`: url functest user guide +.. _`[2]`: http://artifacts.opnfv.org/functest/docs/userguide/index.html .. _`[3]`: https://git.opnfv.org/cgit/releng/tree/jjb/functest/functest-ci-jobs.yml +.. _`[4]`: http://artifacts.opnfv.org/opnfvdocs/brahmaputra/docs/configguide/index.html OPNFV main site: opnfvmain_. |