diff options
Diffstat (limited to 'docs/buildprocedure/build.instruction.rst')
| -rw-r--r-- | docs/buildprocedure/build.instruction.rst | 80 |
1 files changed, 36 insertions, 44 deletions
diff --git a/docs/buildprocedure/build.instruction.rst b/docs/buildprocedure/build.instruction.rst index 8ec8cb7b0..d755ee5fb 100644 --- a/docs/buildprocedure/build.instruction.rst +++ b/docs/buildprocedure/build.instruction.rst @@ -1,14 +1,10 @@ -============================================================================================== -OPNFV Build instruction for the Colorado release of OPNFV when using Fuel as a deployment tool -============================================================================================== - -License -======= - -This work is licensed under a Creative Commons Attribution 4.0 -International License. .. http://creativecommons.org/licenses/by/4.0 .. -(c) Jonas Bjurel (Ericsson AB) and others +.. This document is protected/licensed under the following conditions +.. (c) Jonas Bjurel (Ericsson AB) +.. Licensed under a Creative Commons Attribution 4.0 International License. +.. You should have received a copy of the license along with this work. +.. If not, see <http://creativecommons.org/licenses/by/4.0/>. +======== Abstract ======== @@ -16,6 +12,7 @@ This document describes how to build the Fuel deployment tool for the Colorado release of OPNFV build system, dependencies and required system resources. +============ Introduction ============ @@ -32,20 +29,21 @@ performed by the build system. The audience of this document is assumed to have good knowledge in network and Unix/Linux administration. +============ Requirements ============ Minimum Hardware Requirements ------------------------------ +============================= - ~30 GB available disc - 4 GB RAM Minimum Software Requirements ------------------------------ +============================= -The build host should run Ubuntu 14.04 operating system. +The build host should run Ubuntu 14.04 or 16.04 operating system. On the host, the following packages must be installed: @@ -68,11 +66,13 @@ On the host, the following packages must be installed: - curl (simply available through $ sudo apt-get install curl) +============ Preparations ============ Setting up the Docker build container -------------------------------------- +===================================== + After having installed Docker, add yourself to the docker group: .. code-block:: bash @@ -96,7 +96,8 @@ Then restart docker: $ sudo service docker restart Setting up OPNFV Gerrit in order to being able to clone the code -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +---------------------------------------------------------------- + - Start setting up OPNFV gerrit by creating a SSH key (unless you don't already have one), create one with ssh-keygen @@ -108,7 +109,8 @@ Setting up OPNFV Gerrit in order to being able to clone the code your public key in. Clone the OPNFV code Git repository with your SSH key -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +----------------------------------------------------- + Now it is time to clone the code repository: .. code-block:: bash @@ -126,7 +128,8 @@ Check out the Colorado release: $ git checkout colorado.1.0 Clone the OPNFV code Git repository without a SSH key -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +----------------------------------------------------- + You can also opt to clone the code repository without a SSH key: .. code-block:: bash @@ -136,17 +139,17 @@ You can also opt to clone the code repository without a SSH key: Make sure to checkout the release tag as described above. Support for building behind a http/https/rsync proxy ----------------------------------------------------- +==================================================== The build system is able to make use of a web proxy setup if the http_proxy, https_proxy, no_proxy (if needed) and RSYNC_PROXY or RSYNC_CONNECT_PROG environment variables have been set before invoking make. -The proxy setup must permit port 80 (http), 443 (https) and 873 -(rsync). +The proxy setup must permit port 80 (http) and 443 (https). +Rsync protocol is currently not used during build process. Important note about the host Docker daemon settings -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +---------------------------------------------------- The Docker daemon on the host must be configured to use the http proxy for it to be able to pull the base Ubuntu 14.04 image from the Docker @@ -160,7 +163,7 @@ like: to /etc/default/docker and restarting the Docker daemon. Setting proxy environment variables prior to build -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +-------------------------------------------------- The build system will make use the following environment variables that needs to be exported to subshells by using export (bash) or @@ -185,7 +188,7 @@ As an example, these are the settings that were put in the user's export no_proxy=localhost,127.0.0.1,.consultron.com,.sock Using a ssh proxy for the rsync connection -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +------------------------------------------ If the proxy setup is not allowing the rsync protocol, an alternative solution is to use a SSH tunnel to a machine capable of accessing the @@ -198,25 +201,8 @@ Make sure that the ssh command also refers to the user on the remote system, as the command itself will be run from the Docker build container as the root user (but with the invoking user's SSH keys). -Disabling the Ubuntu repo cache if rsync is not allowed -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - -During the build phase, a local Ubuntu package repository is fetched -from upstream in order to be added to the OPNFV Fuel ISO and for parts -of this process rsync is used. - -If neither of the two available methods for proxying rsync are -available, the last resort is to turn off the caching of the Ubuntu -packages in the build system. This is done by removing the -"f_repobuild" from SUBDIRS in the beginning of -the fuel/build/f_isoroot/Makefile. - -Note! Doing this will require the Fuel master node to have Internet -access when installing the ISO artifact built as no Ubuntu package -cache will be on the ISO! - Configure your build environment --------------------------------- +================================ ** Configuring the build environment should not be performed if building standard Colorado release ** @@ -225,7 +211,8 @@ Select the versions of the components you want to build by editing the fuel/build/config.mk file. Non official build: Selecting which plugins to build ----------------------------------------------------- +==================================================== + In order to cut the build time for unofficial builds (made by an individual developer locally), the selection if which Fuel plugins to build (if any) can be done by environment variable @@ -241,6 +228,7 @@ that this is not a full build. This method of plugin selection is not meant to be used from within Gerrit! +======== Building ======== @@ -251,7 +239,8 @@ There are two methods available for building Fuel: - An abstracted method using build.sh Low level build method using make ---------------------------------- +================================= + The low level method is based on Make: From the <fuel/build> directory, invoke <make [target]> @@ -282,7 +271,8 @@ If the build is successful, you will find the generated ISO file in the <fuel/build/release> subdirectory! Abstracted build method using build.sh --------------------------------------- +====================================== + The abstracted build method uses the <fuel/ci/build.sh> script which allows you to: @@ -293,6 +283,7 @@ allows you to: For more info type <fuel/ci/build.sh -h>. +========= Artifacts ========= @@ -303,6 +294,7 @@ The artifacts produced are: - <OPNFV_XXXX.iso.txt> - Which holds version metadata. +========== References ========== |