1 files changed, 267 insertions, 0 deletions
diff --git a/docs/release/installation/k8s-deploy.rst b/docs/release/installation/k8s-deploy.rst
new file mode 100644
index 00000000..65f638cb
--- /dev/null
+++ b/docs/release/installation/k8s-deploy.rst
@@ -0,0 +1,267 @@
+.. This work is licensed under a Creative Commons Attribution 4.0 International Licence.
+.. http://creativecommons.org/licenses/by/4.0
+.. (c) by Yifei Xue (HUAWEI) and Justin Chi (HUAWEI)
+
+Installation of K8s on virtual machines
+=======================================
+
+Quick Start
+-----------
+
+Only 1 command to try virtual deployment, if you have Internet access. Just Paste it and Run.
+
+.. code-block:: bash
+
+    curl https://raw.githubusercontent.com/opnfv/compass4nfv/master/quickstart_k8s.sh | bash
+
+If you want to deploy noha with1 controller and 1 compute, run the following command
+
+.. code-block:: bash
+
+    export SCENARIO=k8-nosdn-nofeature-noha.yml
+    export VIRT_NUMBER=2
+    curl https://raw.githubusercontent.com/opnfv/compass4nfv/euphrates/quickstart_k8s.sh | bash
+
+Installation of K8s on Bare Metal
+=================================
+
+Nodes Configuration (Bare Metal Deployment)
+-------------------------------------------
+
+The below file is the inventory template of deployment nodes:
+
+"compass4nfv/deploy/conf/hardware_environment/huawei-pod1/k8-nosdn-nofeature-ha.yml"
+
+You can write your own IPMI IP/User/Password/Mac address/roles reference to it.
+
+        - name -- Host name for deployment node after installation.
+
+        - ipmiVer -- IPMI interface version for deployment node support. IPMI 1.0
+          or IPMI 2.0 is available.
+
+        - ipmiIP -- IPMI IP address for deployment node. Make sure it can access
+          from Jumphost.
+
+        - ipmiUser -- IPMI Username for deployment node.
+
+        - ipmiPass -- IPMI Password for deployment node.
+
+        - mac -- MAC Address of deployment node PXE NIC.
+
+        - interfaces -- Host NIC renamed according to NIC MAC addresses when OS provisioning.
+
+        - roles -- Components deployed.
+
+**Set TYPE/FLAVOR and POWER TOOL**
+
+E.g.
+.. code-block:: yaml
+
+    TYPE: baremetal
+    FLAVOR: cluster
+    POWER_TOOL: ipmitool
+
+**Set ipmiUser/ipmiPass and ipmiVer**
+
+E.g.
+
+.. code-block:: yaml
+
+    ipmiUser: USER
+    ipmiPass: PASSWORD
+    ipmiVer: '2.0'
+
+**Assignment of different roles to servers**
+
+E.g. K8s only deployment roles setting
+
+.. code-block:: yaml
+
+    hosts:
+      - name: host1
+        mac: 'F8:4A:BF:55:A2:8D'
+        interfaces:
+           - eth1: 'F8:4A:BF:55:A2:8E'
+        ipmiIp: 172.16.130.26
+        roles:
+          - kube_master
+          - etcd
+
+      - name: host2
+        mac: 'D8:49:0B:DA:5A:B7'
+        interfaces:
+          - eth1: 'D8:49:0B:DA:5A:B8'
+        ipmiIp: 172.16.130.27
+        roles:
+          - kube_node
+
+Network Configuration (Bare Metal Deployment)
+---------------------------------------------
+
+Before deployment, there are some network configuration to be checked based
+on your network topology.Compass4nfv network default configuration file is
+"compass4nfv/deploy/conf/hardware_environment/huawei-pod1/network.yml".
+This file is an example, you can customize by yourself according to specific network
+environment.
+
+In this network.yml, there are several config sections listed following(corresponed to the
+ordre of the config file):
+
+Provider Mapping
+~~~~~~~~~~~~~~~~
+
+        - name -- provider network name.
+
+        - network -- default as physnet, do not change it.
+
+        - interfaces -- the NIC or Bridge attached by the Network.
+
+        - type -- the type of the NIC or Bridge(vlan for NIC and ovs for Bridge, either).
+
+        - roles -- all the possible roles of the host machines which connected by this
+          network(mostly put both controller and compute).
+
+System Interface
+~~~~~~~~~~~~~~~~
+
+        - name -- Network name.
+
+        - interfaces -- the NIC or Bridge attached by the Network.
+
+        - vlan_tag -- if type is vlan, add this tag before 'type' tag.
+
+        - type -- the type of the NIC or Bridge(vlan for NIC and ovs for Bridge, either).
+
+        - roles -- all the possible roles of the host machines which connected by this
+          network(mostly put both controller and compute).
+
+IP Settings
+~~~~~~~~~~~
+
+        - name -- network name corresponding the the network name in System Interface section one by one.
+
+        - ip_ranges -- ip addresses range provided for this network.
+
+        - cidr -- the IPv4 address and its associated routing prefix and subnet mask?
+
+        - gw -- need to add this line only if network is external.
+
+        - roles -- all the possible roles of the host machines which connected by this
+          network(mostly put both controller and compute).
+
+Internal VIP(virtual or proxy IP)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+        - ip -- virtual or proxy ip address, must be in the same subnet with mgmt network
+          but must not be in the range of mgmt network.
+
+        - netmask -- the length of netmask
+
+        - interface -- mostly mgmt.
+
+Public VIP
+~~~~~~~~~~
+
+        - ip -- virtual or proxy ip address, must be in the same subnet with external
+          network but must not be in the range of external network.
+
+        - netmask -- the length of netmask
+
+        - interface -- mostly external.
+
+
+Public Network
+~~~~~~~~~~~~~~
+
+        - enable -- must be True(if False, you need to set up provider network manually).
+
+        - network -- leave it ext-net.
+
+        - type -- the type of the ext-net above, such as flat or vlan.
+
+        - segment_id -- when the type is vlan, this should be id of vlan.
+
+        - subnet -- leave it ext-subnet.
+
+        - provider_network -- leave it physnet.
+
+        - router -- leave it router-ext.
+
+        - enable_dhcp -- must be False.
+
+        - no_gateway -- must be False.
+
+        - external_gw -- same as gw in ip_settings.
+
+        - floating_ip_cidr -- cidr for floating ip, see explanation in ip_settings.
+
+        - floating_ip_start -- define range of floating ip with floating_ip_end(this
+          defined range must not be included in ip range of external configured in
+          ip_settings section).
+
+        - floating_ip_end -- define range of floating ip with floating_ip_start.
+
+
+**The following figure shows the default network configuration.**
+
+.. figure:: images/k8s.png
+    :alt: Kubernetes network configuration
+    :figclass: align-center
+
+    Fig 5. Kubernetes network configuration
+
+Start Deployment (Bare Metal Deployment)
+----------------------------------------
+
+1. Edit deploy.sh
+
+1.1. Set OS version for deployment nodes.
+     Compass4nfv supports ubuntu and centos based openstack newton.
+
+E.g.
+
+.. code-block:: bash
+
+    # Set OS version for target hosts
+    # Only CentOS7 supported now
+    export OS_VERSION=centos7
+
+1.2. Set tarball corresponding to your code
+
+E.g.
+
+.. code-block:: bash
+
+    # Set ISO image corresponding to your code
+    export ISO_URL=file:///home/compass/compass4nfv.tar.gz
+
+1.3. Set hardware deploy jumpserver PXE NIC. (set eth1 E.g.)
+     You do not need to set it when virtual deploy.
+
+E.g.
+
+.. code-block:: bash
+
+    # Set hardware deploy jumpserver PXE NIC
+    # you need to comment out it when virtual deploy
+    export INSTALL_NIC=eth1
+
+1.4. K8s scenario that you want to deploy
+
+E.g.
+
+nosdn-nofeature scenario deploy sample
+
+.. code-block:: bash
+
+    # DHA is your dha.yml's path
+    export DHA=./deploy/conf/hardware_environment/huawei-pod1/k8-nosdn-nofeature-ha.yml
+
+    # NETWORK is your network.yml's path
+    export NETWORK=./deploy/conf/hardware_environment/huawei-pod1/network.yml
+
+2. Run ``deploy.sh``
+
+.. code-block:: bash
+
+    ./deploy.sh