diff options
Diffstat (limited to 'rubbos/app/apache2/conf/workers.properties')
| -rw-r--r-- | rubbos/app/apache2/conf/workers.properties | 215 |
1 files changed, 0 insertions, 215 deletions
diff --git a/rubbos/app/apache2/conf/workers.properties b/rubbos/app/apache2/conf/workers.properties deleted file mode 100644 index df4134bd..00000000 --- a/rubbos/app/apache2/conf/workers.properties +++ /dev/null @@ -1,215 +0,0 @@ - -# workers.properties - -# -# This file provides jk derived plugins with the needed information to -# connect to the different tomcat workers. Note that the distributed -# version of this file requires modification before it is usable by a -# plugin. -# -# As a general note, the characters $( and ) are used internally to define -# macros. Do not use them in your own configuration!!! -# -# Whenever you see a set of lines such as: -# x=value -# y=$(x)\something -# -# the final value for y will be value\something -# -# Normaly all you will need to do is un-comment and modify the first three -# properties, i.e. workers.tomcat_home, workers.java_home and ps. -# Most of the configuration is derived from these. -# -# When you are done updating workers.tomcat_home, workers.java_home and ps -# you should have 3 workers configured: -# -# - An ajp12 worker that connects to localhost:8007 -# - An ajp13 worker that connects to localhost:8009 -# - A jni inprocess worker. -# - A load balancer worker -# -# However by default the plugins will only use the ajp12 worker. To have -# the plugins use other workers you should modify the worker.list property. -# -# - -# OPTIONS ( very important for jni mode ) - -# -# workers.tomcat_home should point to the location where you -# installed tomcat. This is where you have your conf, webapps and lib -# directories. -# -#workers.tomcat_home=/mnt/elba/rubbos/apache-tomcat-5.5.17 -workers.tomcat_home=/bottlenecks/rubbos/app/apache-tomcat-5.5.17 - -# -# workers.java_home should point to your Java installation. Normally -# you should have a bin and lib directories beneath it. -# -#workers.java_home=/mnt/elba/rubbos/jdk1.6.0_27 -workers.java_home=/bottlenecks/rubbos/app/jdk1.6.0_27 - -# -# You should configure your environment slash... ps=\ on NT and / on UNIX -# and maybe something different elsewhere. -# -ps=/ - -# -#------ ADVANCED MODE ------------------------------------------------ -#--------------------------------------------------------------------- -# - -# -#------ DEFAULT worket list ------------------------------------------ -#--------------------------------------------------------------------- -# -# -# The workers that your plugins should create and work with -# -# Add 'inprocess' if you want JNI connector -worker.list=worker1 -# , inprocess - - -worker.TOMCAT1.port=8009 -worker.TOMCAT1.host=node8 -worker.TOMCAT1.type=ajp13 -worker.TOMCAT1.lbfactor=1 - - -# -#------ DEFAULT ajp12 WORKER DEFINITION ------------------------------ -#--------------------------------------------------------------------- -# - -# -# Defining a worker named ajp12 and of type ajp12 -# Note that the name and the type do not have to match. -# -#worker.ajp12.port=8007 -#worker.ajp12.host=localhost -#worker.ajp12.type=ajp12 -# -# Specifies the load balance factor when used with -# a load balancing worker. -# Note: -# ----> lbfactor must be > 0 -# ----> Low lbfactor means less work done by the worker. -#worker.ajp12.lbfactor=1 - -# -#------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ -#--------------------------------------------------------------------- -# - -# -# Defining a worker named ajp13 and of type ajp13 -# Note that the name and the type do not have to match. -# -#worker.ajp13.port=8009 -#worker.ajp13.host=node60.rubbostest.Infosphere.emulab.net -#worker.ajp13.type=ajp13 -# -# Specifies the load balance factor when used with -# a load balancing worker. -# Note: -# ----> lbfactor must be > 0 -# ----> Low lbfactor means less work done by the worker. -#worker.ajp13.lbfactor=1 - -# -# Specify the size of the open connection cache. -#worker.ajp13.cachesize - -# -#------ DEFAULT LOAD BALANCER WORKER DEFINITION ---------------------- -#--------------------------------------------------------------------- -# - -# -# The router (type lb) workers perform wighted round-robin -# load balancing with sticky sessions. -# Note: -# ----> If a worker dies, the load balancer will check its state -# once in a while. Until then all work is redirected to peer -# workers. -worker.worker1.type=lb -worker.worker1.balance_workers=TOMCAT1 -worker.worker1.sticky_session=True -worker.worker1.method=Session - -# -#------ DEFAULT JNI WORKER DEFINITION--------------------------------- -#--------------------------------------------------------------------- -# - -# -# Defining a worker named inprocess and of type jni -# Note that the name and the type do not have to match. -# -worker.inprocess.type=jni - -# -#------ CLASSPATH DEFINITION ----------------------------------------- -#--------------------------------------------------------------------- -# - -# -# Additional class path components. -# -worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)tomcat.jar - -# -# Setting the command line for tomcat. -# Note: The cmd_line string may not contain spaces. -# -worker.inprocess.cmd_line=start - -# Not needed, but can be customized. -#worker.inprocess.cmd_line=-config -#worker.inprocess.cmd_line=$(workers.tomcat_home)$(ps)conf$(ps)server.xml -#worker.inprocess.cmd_line=-home -#worker.inprocess.cmd_line=$(workers.tomcat_home) - -# -# The JVM that we are about to use -# -# This is for Java2 -# -# Windows -#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)jvm.dll -# IBM JDK1.3 -#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)libjvm.so -# Unix - Sun VM or blackdown -#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)lib$(ps)i386$(ps)classic$(ps)libjvm.so -worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)lib$(ps)i386$(ps)server$(ps)libjvm.so - -# -# And this is for jdk1.1.X -# -#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)bin$(ps)javai.dll - - -# -# Setting the place for the stdout and stderr of tomcat -# -worker.inprocess.stdout=$(workers.tomcat_home)$(ps)logs$(ps)inprocess.stdout -worker.inprocess.stderr=$(workers.tomcat_home)$(ps)logs$(ps)inprocess.stderr - -# -# Setting the tomcat.home Java property -# -#worker.inprocess.sysprops=tomcat.home=$(workers.tomcat_home) - -# -# Java system properties -# -# worker.inprocess.sysprops=java.compiler=NONE -# worker.inprocess.sysprops=myprop=mypropvalue - -# -# Additional path components. -# -# worker.inprocess.ld_path=d:$(ps)SQLLIB$(ps)bin -# |