path: root/docs/installation-instruction.rst

====================================================================================================================
OPNFV Installation instruction for the AArch64 Brahmaputra 3.0 release of OPNFV when using Fuel as a deployment tool
====================================================================================================================

License
=======

This work is licensed under a Creative Commons Attribution 4.0 International
License. .. http://creativecommons.org/licenses/by/4.0 ..
(c) Jonas Bjurel (Ericsson AB) and others

Abstract
========

This document describes how to install the Brahmaputra 3.0 release of
OPNFV when using Fuel as a deployment tool, with an AArch64 (only) target node pool.

Introduction
============

This document provides guidelines on how to install and
configure the Brahmaputra 3.0 release of OPNFV when using Fuel as a
deployment tool, with an AArch64 (only) target node pool,
including required software and hardware configurations.

Although the available installation options give a high degree of
freedom in how the system is set-up, including architecture, services
and features, etc., said permutations may not provide an OPNFV
compliant reference architecture. This instruction provides a
step-by-step guide that results in an OPNFV Brahmaputra compliant
deployment.

The audience of this document is assumed to have good knowledge in
networking and Unix/Linux administration.

Preface
=======
Before starting the installation of the AArch64 Brahmaputra 3.0 release of
OPNFV, using Fuel as a deployment tool, some planning must be
done.

Retrieving the ISO image
------------------------

First of all, the Fuel deployment ISO image needs to be retrieved, the
Fuel .iso image of the AArch64 Brahmaputra release can be found at *Reference: 2*

Building the ISO image
----------------------

Alternatively, you may build the  .iso from source by cloning the
opnfv/armband git repository.  To retrieve the repository for the AArch64 Brahmaputra 3.0 release use the following command:

$git clone https://<linux foundation uid>@gerrit.opnf.org/gerrit/armband

Check-out the Brahmaputra stable branch to set the branch to the
baseline required to replicate the Brahmaputra release:

$ git checkout stable/brahmaputra

Go to the armband directory and build the .iso:

$ cd armband; make release

For more information on how to build, please see *Reference: 14*

Other preparations
------------------


Next, familiarize yourself with Fuel by reading the following documents:

- Fuel planning guide, please see *Reference: 8*

- Fuel user guide, please see *Reference: 9*

- Fuel operations guide, please see *Reference: 10*

- Fuel Plugin Developers Guide, please see *Reference: 11*

Prior to installation, a number of deployment specific parameters must be collected, those are:

#.     Provider sub-net and gateway information

#.     Provider VLAN information

#.     Provider DNS addresses

#.     Provider NTP addresses

#.     Network overlay you plan to deploy (VLAN, VXLAN, FLAT)

#.     How many nodes and what roles you want to deploy (Controllers, Storage, Computes)

#.     Monitoring options you want to deploy (Ceilometer, Syslog, erc.).

#.     Other options not covered in the document are available in the links above


This information will be needed for the configuration procedures
provided in this document.

Hardware requirements
=====================

The following minimum hardware requirements must be met for the
installation of Brahmaputra using Fuel:

+--------------------+------------------------------------------------------+
| **HW Aspect**      | **Requirement**                                      |
|                    |                                                      |
+====================+======================================================+
| **# of nodes**     | Minimum 5 (3 for non redundant deployment):          |
|                    |                                                      |
|                    | - 1 Fuel deployment master (may be virtualized)      |
|                    |                                                      |
|                    | - 3(1) Controllers (1 colocated mongo/ceilometer     |
|                    |   role, 2 Ceph-OSD roles)                            |
|                    |                                                      |
|                    | - 1 Compute (1 co-located Ceph-OSD role)             |
|                    |                                                      |
+--------------------+------------------------------------------------------+
| **CPU**            | Minimum 1 socket x86_AMD64 with Virtualization       |
|                    | support                                              |
+--------------------+------------------------------------------------------+
| **RAM**            | Minimum 16GB/server (Depending on VNF work load)     |
|                    |                                                      |
+--------------------+------------------------------------------------------+
| **Disk**           | Minimum 256GB 10kRPM spinning disks                  |
|                    |                                                      |
+--------------------+------------------------------------------------------+
| **Networks**       | 4 Tagged VLANs (PUBLIC, MGMT, STORAGE, PRIVATE)      |
|                    |                                                      |
|                    | 1 Un-Tagged VLAN for PXE Boot - ADMIN Network        |
|                    |                                                      |
|                    | Note: These can be allocated to a single NIC -       |
|                    | or spread out over multiple NICs as your hardware    |
|                    | supports.                                            |
+--------------------+------------------------------------------------------+

Help with Hardware Requirements
===============================

Calculate hardware requirements:

For information on compatible hardware types available for use, please see *Reference: 11*.

When choosing the hardware on which you will deploy your OpenStack
environment, you should think about:

- CPU -- Consider the number of virtual machines that you plan to deploy in your cloud environment and the CPU per virtual machine.

- Memory -- Depends on the amount of RAM assigned per virtual machine and the controller node.

- Storage -- Depends on the local drive space per virtual machine, remote volumes that can be attached to a virtual machine, and object storage.

- Networking -- Depends on the Choose Network Topology, the network bandwidth per virtual machine, and network storage.


Top of the rack (TOR) Configuration requirements
================================================

The switching infrastructure provides connectivity for the OPNFV
infrastructure operations, tenant networks (East/West) and provider
connectivity (North/South); it also provides needed connectivity for
the Storage Area Network (SAN).
To avoid traffic congestion, it is strongly suggested that three
physically separated networks are used, that is: 1 physical network
for administration and control, one physical network for tenant private
and public networks, and one physical network for SAN.
The switching connectivity can (but does not need to) be fully redundant,
in such case it comprises a redundant 10GE switch pair for each of the
three physically separated networks.

The physical TOR switches are **not** automatically configured from
the Fuel OPNFV reference platform. All the networks involved in the OPNFV
infrastructure as well as the provider networks and the private tenant
VLANs needs to be manually configured.

Manual configuration of the Brahmaputra hardware platform should
be carried out according to the OPNFV Pharos specification:
<https://wiki.opnfv.org/pharos/pharos_specification>

OPNFV Software installation and deployment
==========================================

This section describes the installation of the OPNFV installation
server (Fuel master) as well as the deployment of the full OPNFV
reference platform stack across a server cluster.

Install Fuel master
-------------------
#. Mount the Brahmaputra Fuel ISO file/media as a boot device to the jump host server.

#. Reboot the jump host to establish the Fuel server.

   - The system now boots from the ISO image.

   - Select "Fuel Install (Static IP)" (See figure below)

   - Press [Enter].

   .. figure:: img/grub-1.png

#. Wait until screen Fuel setup is shown (Note: This can take up to 30 minutes).

#. In the "Fuel User" section - Confirm/change the default password (See figure below)

   - Enter "admin" in the Fuel password input

   - Enter "admin" in the Confirm password input

   - Select "Check" and press [Enter]

   .. figure:: img/fuelmenu1.png

#. In the "Network Setup" section - Configure DHCP/Static IP information for your FUEL node - For example, ETH0 is 10.20.0.2/24 for FUEL booting and ETH1 is DHCP/Static in your corporate/lab network (see figure below).

   - Configuration of ETH1 interface for connectivity into your corporate/lab network is mandatory. You need to have internet access over this interface.
     Due to the architecture of ports.ubuntu.com mirror, currently Fuel cannot create a full local mirror of all required AArch64 packages. Internet access is needed to deploy with Fuel on AArch64 nodes.

   .. figure:: img/fuelmenu2.png

   .. figure:: img/fuelmenu2a.png

#. In the "PXE Setup" section (see figure below) - Change the following fields to appropriate values (example below):

   - DHCP Pool Start 10.20.0.3

   - DHCP Pool End 10.20.0.254

   - DHCP Pool Gateway  10.20.0.2 (IP address of Fuel node)

   .. figure:: img/fuelmenu3.png

#. In the "DNS & Hostname" section (see figure below) - Change the following fields to appropriate values:

   - Hostname

   - Domain

   - Search Domain

   - External DNS

   - Hostname to test DNS

   - Select <Check> and press [Enter]

   .. figure:: img/fuelmenu4.png


#. OPTION TO ENABLE PROXY SUPPORT - In the "Bootstrap Image" section (see figure below), edit the following fields to define a proxy. (**NOTE:** cannot be used in tandem with local repository support)

   - Navigate to "HTTP proxy" and enter your http proxy address

   - Select <Check> and press [Enter]

   .. figure:: img/fuelmenu5.png

#. In the "Time Sync" section (see figure below) - Change the following fields to appropriate values:

   - NTP Server 1 <Customer NTP server 1>

   - NTP Server 2 <Customer NTP server 2>

   - NTP Server 3 <Customer NTP server 3>

   .. figure:: img/fuelmenu6.png

#. Start the installation.

   - Select Quit Setup and press Save and Quit.

   - Installation starts, wait until the login screen is shown.


Boot the Node Servers
---------------------

After the Fuel Master node has rebooted from the above steps and is at
the login prompt, you should boot the Node Servers (Your
Compute/Control/Storage blades (nested or real) with a PXE booting
scheme so that the FUEL Master can pick them up for control.

#. Enable PXE booting

   - For every controller and compute server: enable PXE Booting as the first boot device in the BIOS boot order menu and hard disk as the second boot device in the same menu.

#. Reboot all the control and compute blades.

#. Wait for the availability of nodes showing up in the Fuel GUI.

   - Connect to the FUEL UI via the URL provided in the Console (default: https://10.20.0.2:8443)

   - Wait until all nodes are displayed in top right corner of the Fuel GUI: Total nodes and Unallocated nodes (see figure below).

   .. figure:: img/nodes.png


Target specific configuration
-----------------------------

#. AMD Softiron

   For these targets, "rx-vlan-filter" offloading has to be turned off on the interface destined for OpenStack traffic (not the interface used for PXE boot).
   For now this setting cannot be toggled from Fuel GUI, so it has to be done form the console.

   - From Fuel master console identify target nodes admin IPs (see figure below).

     .. figure:: img/fuelconsole1.png

   - SSH into each of the target nodes and disable rx-vlan-filter on the physical interface allocated for OpenStack traffic  (see figure below).

     .. figure:: img/softiron1.png

   - Repeat the step above for all AMD Softiron nodes in the POD.


Install additional Plugins/Features on the FUEL node
----------------------------------------------------

#. SSH to your FUEL node (e.g. root@10.20.0.2  pwd: r00tme)

#. Select wanted plugins/features from the /opt/opnfv/ directory.

#. Install the wanted plugin with the command "fuel plugins --install /opt/opnfv/<plugin-name>-<version>.<arch>.rpm"
   Expected output: "Plugin ....... was successfully installed." (see figure below)

   .. figure:: img/plugin_install.png

Create an OpenStack Environment
-------------------------------

#. Connect to Fuel WEB UI with a browser (default: https://10.20.0.2:8443) (login admin/admin)

#. Create and name a new OpenStack environment, to be installed.

   .. figure:: img/newenv.png

#. Select "<Liberty on Ubuntu 14.04 (aarch64)>" and press <Next>

#. Select "compute virtulization method".

   - Select "QEMU-KVM as hypervisor" and press <Next>

#. Select "network mode".

   - Select "Neutron with ML2 plugin"

   - Select "Neutron with tunneling segmentation" (Required when using the ODL or ONOS plugins)

   - Press <Next>

#. Select "Storage Back-ends".

   - Select "Ceph for block storage" and press <Next>

#. Select "additional services" you wish to install.

   - Check option "Install Celiometer (OpenStack Telemetry)" and press <Next>

#. Create the new environment.

   - Click <Create> Button

Configure the network environment
---------------------------------

#. Open the environment you previously created.

#. Open the networks tab and select the "default Node Networks group to" on the left pane (see figure below).

   .. figure:: img/network.png

#. Update the Public network configuration and change the following fields to appropriate values:

   - CIDR to <CIDR for Public IP Addresses>

   - IP Range Start to <Public IP Address start>

   - IP Range End to <Public IP Address end>

   - Gateway to <Gateway for Public IP Addresses>

   - Check <VLAN tagging>.

   - Set appropriate VLAN id.

#. Update the Storage Network Configuration

   - Set CIDR to appropriate value  (default 192.168.1.0/24)

   - Set IP Range Start to appropriate value (default 192.168.1.1)

   - Set IP Range End to appropriate value (default 192.168.1.254)

   - Set vlan to appropriate value  (default 102)

#. Update the Management network configuration.

   - Set CIDR to appropriate value (default 192.168.0.0/24)

   - Set IP Range Start to appropriate value (default 192.168.0.1)

   - Set IP Range End to appropriate value (default 192.168.0.254)

   - Check <VLAN tagging>.

   - Set appropriate VLAN id. (default 101)

#. Update the Private Network Information

   - Set CIDR to appropriate value (default 192.168.2.0/24

   - Set IP Range Start to appropriate value (default 192.168.2.1)

   - Set IP Range End to appropriate value (default 192.168.2.254)

   - Check <VLAN tagging>.

   - Set appropriate VLAN tag (default 103)

#. Select the "Neutron L3 Node Networks group" on the left pane.

   .. figure:: img/neutronl3.png

#. Update the Floating Network configuration.

   - Set the Floating IP range start (default 172.16.0.130)

   - Set the Floating IP range end (default 172.16.0.254)

   - Set the Floating network name (default admin_floating_net)

#. Update the Internal Network configuration.

   - Set Internal network CIDR to an appropriate value (default 192.168.111.0/24)

   - Set Internal network gateway to an appropriate value

   - Set the Internal network name (default admin_internal_net)

#. Update the Guest OS DNS servers.

   - Set Guest OS DNS Server values appropriately

#. Save Settings.

#. Select the "Other Node Networks group" on the left pane(see figure below).

   .. figure:: img/other.png

#. Update the Public network assignment.

   - Check the box for "Assign public network to all nodes" (Required by OpenDaylight)

#. Update Host OS DNS Servers.

   - Provide the DNS server settings

#. Update Host OS NTP Servers.

   - Provide the NTP server settings

Select Hypervisor type
----------------------

#. In the FUEL UI of your Environment, click the "Settings" Tab

#. Select Compute on the left side pane (see figure below)

   - Check the KVM box and press "Save settings"

   .. figure:: img/compute.png

Enable Plugins
--------------

#. In the FUEL UI of your Environment, click the "Settings" Tab

#. Select Other on the left side pane (see figure below)

   - Enable and configure the plugins of your choice

   .. figure:: img/plugins.png

Allocate nodes to environment and assign functional roles
---------------------------------------------------------

#. Click on the "Nodes" Tab in the FUEL WEB UI (see figure below).

    .. figure:: img/addnodes.png

#. Assign roles (see figure below).

    - Click on the <+Add Nodes> button

    - Check <Controller>, <Telemetry - MongoDB>  and optionally an SDN Controller role (OpenDaylight controller/ONOS) in the Assign Roles Section.

    - Check one node which you want to act as a Controller from the bottom half of the screen

    - Click <Apply Changes>.

    - Click on the <+Add Nodes> button

    - Check the <Controller> and <Storage - Ceph OSD> roles.

    - Check the two next nodes you want to act as Controllers from the bottom half of the screen

    - Click <Apply Changes>

    - Click on <+Add Nodes> button

    - Check the <Compute> and <Storage - Ceph OSD> roles.

    - Check the Nodes you want to act as Computes from the bottom half of the screen

    - Click <Apply Changes>.

    .. figure:: img/computelist.png

#. Configure interfaces (see figure below).

    - Check Select <All> to select all allocated nodes

    - Click <Configure Interfaces>

    - Assign interfaces (bonded) for mgmt-, admin-, private-, public-
      and storage networks

    - Click <Apply>

    .. figure:: img/interfaceconf.png


OPTIONAL - Set Local Mirror Repos
---------------------------------

The following steps can be executed if you are in an environment with
no connection to the Internet. The Fuel server delivers a local repo
that can be used for installation / deployment of openstack.

#. In the Fuel UI of your Environment, click the Settings Tab and select General from the left pane.

   - Replace the URI values for the "Name" values outlined below:

   - "ubuntu" URI="deb http://<ip-of-fuel-server>:8080/mirrors/ubuntu/ trusty main"

   - "ubuntu-security" URI="deb http://<ip-of-fuel-server>:8080/mirrors/ubuntu/ trusty-security main"

   - "ubuntu-updates" URI="deb http://<ip-of-fuel-server>:8080/mirrors/ubuntu/ trusty-updates main"

   - "mos" URI="deb http://<ip-of-fuel-server>::8080/liberty-8.0/ubuntu/x86_64 mos8.0 main restricted"

   - "Auxiliary" URI="deb http://<ip-of-fuel-server>:8080/liberty-8.0/ubuntu/auxiliary auxiliary main restricted"

   - Click <Save Settings> at the bottom to Save your changes

Verify Networks
---------------

It is important that the Verify Networks action is performed as it will verify
that communicate works for the networks you have setup, as well as check that
packages needed for a successful deployment can be fetched.

#. From the FUEL UI in your Environment, Select the Networks Tab and select "Connectivity check" on the left pane (see figure below)

   - Select <Verify Networks>

   - Continue to fix your topology (physical switch, etc) until the "Verification Succeeded" and "Your network is configured correctly" message is shown

   .. figure:: img/verifynet.png


Deploy Your Environment
-----------------------

38. Deploy the environment.

    - In the Fuel GUI, click on the "Dashboard" Tab.

    - Click on <Deploy Changes> in the "Ready to Deploy?" section

    - Examine any information notice that pops up and click <Deploy>

    Wait for your deployment to complete, you can view the "Dashboard"
    Tab to see the progress and status of your deployment.

Installation health-check
=========================

#. Perform system health-check (see figure below)

    - Click the "Health Check" tab inside your Environment in the FUEL Web UI

    - Check <Select All> and Click <Run Tests>

    - Allow tests to run and investigate results where appropriate

    .. figure:: img/health.png

References
==========

OPNFV
-----

1) `OPNFV Home Page <www.opnfv.org>`_

2) `OPNFV documentation- and software downloads <https://www.opnfv.org/software/download>`_

OpenStack
---------

3) `OpenStack Liberty Release artifacts <http://www.openstack.org/software/liberty>`_

4) `OpenStack documentation <http://docs.openstack.org>`_

OpenDaylight
------------

5) `OpenDaylight artifacts <http://www.opendaylight.org/software/downloads>`_

Fuel
----
6) `The Fuel OpenStack project <https://wiki.openstack.org/wiki/Fuel>`_

7) `Fuel documentation overview <https://docs.fuel-infra.org/openstack/fuel/fuel-8.0/>`_

8) `Fuel planning guide <https://docs.fuel-infra.org/openstack/fuel/fuel-8.0/mos-planning-guide.html>`_

9) `Fuel quick start guide <https://docs.mirantis.com/openstack/fuel/fuel-8.0/quickstart-guide.html>`_

10) `Fuel operations guide <https://docs.mirantis.com/openstack/fuel/fuel-8.0/operations.html>`_

11) `Fuel Plugin Developers Guide <https://wiki.openstack.org/wiki/Fuel/Plugins>`_

12) `Fuel OpenStack Hardware Compatibility List <https://www.mirantis.com/products/openstack-drivers-and-plugins/hardware-compatibility-list>`_

Fuel in OPNFV
-------------

13) `OPNFV Installation instruction for the AArch64 Brahmaputra release of OPNFV when using Fuel as a deployment tool <http://artifacts.opnfv.org/armband/brahmaputra/docs/installation-instruction.html>`_

14) `OPNFV Build instruction for the AArch64 Brahmaputra release of OPNFV when using Fuel as a deployment tool <http://artifacts.opnfv.org/armband/brahmaputra/docs/build-instruction.html>`_

15) `OPNFV Release Note for the AArch64 Brahmaputra release of OPNFV when using Fuel as a deployment tool <http://artifacts.opnfv.org/armband/brahmaputra/docs/release-notes.html>`_