| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This change adds the ManagementInterfaceDefaultRoute parameter
for setting the Management network as the default route in some
deployments. Notes were added to indicate that if the Management
network is used as the default gateway, then the default route
on the control plane should be commented out.
The sample network-environment.yaml was modified to include the
ManagementInterfaceDefaultRoute, but this is commented out like
the rest of the Management network parameters.
This change also adds the ControlPlaneDefaultRoute and
ExternalInterfaceDefaultRoute to all templates, so that if the
networks are customized, the NIC configs can be modified without
having to modify the parameters section of the template. The
default for the ExternalInterfaceDefaultRoute is '10.0.0.1', and
the default for ManagementInterfaceDefaultRoute is set to 'unset'.
This change also converts the single-nic-linux-bridge-vlans from
DHCP to static IPs on the Control Plane Interface, bringing these
templates in line with the rest of the NIC config templates. The
parameters needed to be updated in these templates as well.
The controller-v6.yaml templates had a default value of "10.0.0.1"
for the ExternalInterfaceDefaultRoute. This was confusing, and is
now undefined.
This change also sets a default gateway on the Control Plane in
controller-no-external.yaml templates.
Change-Id: I8ea6733fe46902e1baeff4ccfbcd42ecc5a1825f
|
|
This change adds Controller NIC configs for the sample NIC config
templates that are compatible with IPv6 on the External network.
These controller-v6.yaml templates include a default route for IPv6
on the External network, and a default route for IPv4 on the Control
Plane. The Heat parameters ExternalNetworkDefaultRoute and
ControlPlaneDefaultRoute are used to set these values.
Change-Id: Ifed8cb359eae1d9d623d3eb2fe40ea8a0d1d889a
|
|
One of the interfaces was not indented at the same level as the
others in some of the templates.
Change-Id: Iabd835724848d754d5522968e1c8e3cf9f78e6c6
|
|
This change adds a system management network to all overcloud
nodes. The purpose of this network is for system administration,
for access to infrastructure services like DNS or NTP, or for
monitoring. This allows the management network to be placed on a
bond for redundancy, or for the system management network to be
an out-of-band network with no routing in or out. The management
network might also be configured as a default route instead of the
provisioning 'ctlplane' network.
This change does not enable the management network by default. An
environment file named network-management.yaml may be included to
enable the network and ports for each role. The included NIC config
templates have been updated with a block that may be uncommented
when the management network is enabled.
This change also contains some minor cleanup to the NIC templates,
particularly the multiple nic templates.
Change-Id: I0813a13f60a4f797be04b34258a2cffa9ea7e84f
|
|
The non-controller nodes in the network/config/multiple-nics
directory do not have a default route configured. This change
adds the default route to the non-controller nodes using the
ControlPlaneDefaultRoute parameter, which was already a part
of these templates.
Change-Id: Idaaeb2a539555ac14cc613b202c428108bc19a30
|
|
This change adds a set of network interface configurations for use
with network isolation. The multiple-nics templates includes one
separate NIC per network, and assumes that nic1 is used for the
provisioning network (ctlplane). Also included is an environment
file for including the multiple-nics configuration in a deployment.
This revision changes the ordering of the NICs. By doing that, it
is possible to wire up only a subset of the NICs for the storage
nodes, and it is possilbe to leave the External NIC only configured
on the controllers.
rdo: Updated this commit for static control plane configuration
Co-Authored-By: Rhys Oxenham <roxenham@redhat.com>
Change-Id: Ic878d1ed1a85b5705295d087a743570ca8213504
|
Dan Sneddon
Ben Nemec