From e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb Mon Sep 17 00:00:00 2001 From: Yang Zhang Date: Fri, 28 Aug 2015 09:58:54 +0800 Subject: Add qemu 2.4.0 Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang --- qemu/roms/u-boot/include/configs/katmai.h | 324 ++++++++++++++++++++++++++++++ 1 file changed, 324 insertions(+) create mode 100644 qemu/roms/u-boot/include/configs/katmai.h (limited to 'qemu/roms/u-boot/include/configs/katmai.h') diff --git a/qemu/roms/u-boot/include/configs/katmai.h b/qemu/roms/u-boot/include/configs/katmai.h new file mode 100644 index 000000000..fa72eb02f --- /dev/null +++ b/qemu/roms/u-boot/include/configs/katmai.h @@ -0,0 +1,324 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2004 Paul Reynolds + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/************************************************************************ + * katmai.h - configuration for AMCC Katmai (440SPe) + ***********************************************************************/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_KATMAI 1 /* Board is Katmai */ +#define CONFIG_440 1 /* ... PPC440 family */ +#define CONFIG_440SPE 1 /* Specifc SPe support */ +#define CONFIG_440SPE_REVA 1 /* Support old Rev A. */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ + +#define CONFIG_SYS_TEXT_BASE 0xFFFA0000 + +/* + * Enable this board for more than 2GB of SDRAM + */ +#define CONFIG_PHYS_64BIT +#define CONFIG_VERY_BIG_RAM + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME katmai +#include "amcc-common.h" + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#undef CONFIG_SHOW_BOOT_PROGRESS + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ +#define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */ + +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE + +#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ +#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ +#define CONFIG_SYS_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ + +#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000 +#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000 +#define CONFIG_SYS_PCIE2_CFGBASE 0xc2000000 +#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000 +#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000 +#define CONFIG_SYS_PCIE2_XCFGBASE 0xc3002000 + +/* base address of inbound PCIe window */ +#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL + +/* System RAM mapped to PCI space */ +#define CONFIG_PCI_SYS_MEM_BUS CONFIG_SYS_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_PHYS CONFIG_SYS_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024) + +#define CONFIG_SYS_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */ + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer (placed in internal SRAM) + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#undef CONFIG_SYS_EXT_SERIAL_CLOCK + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */ +#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/ +#define CONFIG_DDR_ECC 1 /* with ECC support */ +#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* optimal value found by GDA*/ +#undef CONFIG_STRESS + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 + +#define CONFIG_SYS_SPD_BUS_NUM 0 /* The I2C bus for SPD */ + +#define IIC0_BOOTPROM_ADDR 0x50 +#define IIC0_ALT_BOOTPROM_ADDR 0x54 + +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR (0x50) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* I2C bootstrap EEPROM */ +#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x50 +#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 +#define CONFIG_4xx_CONFIG_BLOCKSIZE 8 + +/* I2C RTC */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */ + +/* I2C DTT */ +#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ +#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ +/* + * standard dtt sensor configuration - bottom bit will determine local or + * remote sensor of the ADM1021, the rest determines index into + * CONFIG_SYS_DTT_ADM1021 array below. + */ +#define CONFIG_DTT_SENSORS { 0, 1 } + +/* + * ADM1021 temp sensor configuration (see dtt/adm1021.c for details). + * there will be one entry in this array for each two (dummy) sensors in + * CONFIG_DTT_SENSORS. + * + * For Katmai board: + * - only one ADM1021 + * - i2c addr 0x18 + * - conversion rate 0x02 = 0.25 conversions/second + * - ALERT ouput disabled + * - local temp sensor enabled, min set to 0 deg, max set to 85 deg + * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg + */ +#define CONFIG_SYS_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} } + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ + +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + "kernel_addr=ff000000\0" \ + "fdt_addr=ff1e0000\0" \ + "ramdisk_addr=ff200000\0" \ + "pciconfighost=1\0" \ + "pcie_mode=RP:RP:RP\0" \ + "" + +/* + * Commands additional to the ones defined in amcc-common.h + */ +#define CONFIG_CMD_CHIP_CONFIG +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ECCTEST +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP + +#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */ +#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ +#define CONFIG_HAS_ETH0 +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 1000 +#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ + +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCI_CONFIG_HOST_BRIDGE + +/* Board-specific PCI */ +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ +#undef CONFIG_SYS_PCI_MASTER_INIT + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +/* #define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_DEVICEID */ + +/* + * NETWORK Support (PCI): + */ +/* Support for Intel 82557/82559/82559ER chips. */ +#define CONFIG_EEPRO100 + +/*----------------------------------------------------------------------- + * Xilinx System ACE support + *----------------------------------------------------------------------*/ +#define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */ +#define CONFIG_SYS_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */ +#define CONFIG_SYS_SYSTEMACE_BASE CONFIG_SYS_ACE_BASE +#define CONFIG_DOS_PARTITION 1 + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ + +/* Memory Bank 0 (Flash) initialization */ +#define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \ + EBC_BXAP_TWT_ENCODE(7) | \ + EBC_BXAP_BCE_DISABLE | \ + EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | \ + EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | \ + EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | \ + EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | \ + EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED) +#define CONFIG_SYS_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | \ + EBC_BXCR_BS_16MB | \ + EBC_BXCR_BU_RW | \ + EBC_BXCR_BW_16BIT) + +/* Memory Bank 1 (Xilinx System ACE controller) initialization */ +#define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \ + EBC_BXAP_TWT_ENCODE(4) | \ + EBC_BXAP_BCE_DISABLE | \ + EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | \ + EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | \ + EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | \ + EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_NONDELAYED | \ + EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED) +#define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_ACE_BASE) | \ + EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | \ + EBC_BXCR_BW_16BIT) + +/*------------------------------------------------------------------------- + * Initialize EBC CONFIG - + * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC + * default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000 + *-------------------------------------------------------------------------*/ +#define CONFIG_SYS_EBC_CFG (EBC_CFG_LE_UNLOCK | \ + EBC_CFG_PTD_ENABLE | \ + EBC_CFG_RTC_16PERCLK | \ + EBC_CFG_ATC_PREVIOUS | \ + EBC_CFG_DTC_PREVIOUS | \ + EBC_CFG_CTC_PREVIOUS | \ + EBC_CFG_OEO_PREVIOUS | \ + EBC_CFG_EMC_DEFAULT | \ + EBC_CFG_PME_DISABLE | \ + EBC_CFG_PR_16) + +/*----------------------------------------------------------------------- + * GPIO Setup + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_GPIO_PCIE_PRESENT0 17 +#define CONFIG_SYS_GPIO_PCIE_PRESENT1 21 +#define CONFIG_SYS_GPIO_PCIE_PRESENT2 23 +#define CONFIG_SYS_GPIO_RS232_FORCEOFF 30 + +#define CONFIG_SYS_PFC0 (GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT0) | \ + GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT1) | \ + GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT2) | \ + GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF)) +#define CONFIG_SYS_GPIO_OR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF) +#define CONFIG_SYS_GPIO_TCR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF) +#define CONFIG_SYS_GPIO_ODR 0 + +#endif /* __CONFIG_H */ -- cgit 1.2.3-korg