From e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb Mon Sep 17 00:00:00 2001 From: Yang Zhang Date: Fri, 28 Aug 2015 09:58:54 +0800 Subject: Add qemu 2.4.0 Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang --- qemu/roms/u-boot/include/configs/NETPHONE.h | 701 ++++++++++++++++++++++++++++ 1 file changed, 701 insertions(+) create mode 100644 qemu/roms/u-boot/include/configs/NETPHONE.h (limited to 'qemu/roms/u-boot/include/configs/NETPHONE.h') diff --git a/qemu/roms/u-boot/include/configs/NETPHONE.h b/qemu/roms/u-boot/include/configs/NETPHONE.h new file mode 100644 index 000000000..08cfc9e4b --- /dev/null +++ b/qemu/roms/u-boot/include/configs/NETPHONE.h @@ -0,0 +1,701 @@ +/* + * (C) Copyright 2000-2010 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Pantelis Antoniou, Intracom S.A., panto@intracom.gr + * U-Boot port on NetTA4 board + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#if !defined(CONFIG_NETPHONE_VERSION) || CONFIG_NETPHONE_VERSION > 2 +#error Unsupported CONFIG_NETPHONE version +#endif + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC870 1 /* This is a MPC885 CPU */ +#define CONFIG_NETPHONE 1 /* ...on a NetPhone board */ + +#define CONFIG_SYS_TEXT_BASE 0x40000000 + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE + +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ + +/* #define CONFIG_XIN 10000000 */ +#define CONFIG_XIN 50000000 +/* #define MPC8XX_HZ 120000000 */ +#define MPC8XX_HZ 66666666 + +#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "tftpboot; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ + "bootm" + +#define CONFIG_SOURCE +#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_NISDOMAIN + +#undef CONFIG_MAC_PARTITION +#undef CONFIG_DOS_PARTITION + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define FEC_ENET 1 /* eth.c needs it that way... */ +#undef CONFIG_SYS_DISCOVER_PHY +#define CONFIG_MII 1 +#define CONFIG_MII_INIT 1 +#define CONFIG_RMII 1 /* use RMII interface */ + +#define CONFIG_ETHER_ON_FEC1 1 +#define CONFIG_FEC1_PHY 8 /* phy address of FEC */ +#define CONFIG_FEC1_PHY_NORXERR 1 + +#define CONFIG_ETHER_ON_FEC2 1 +#define CONFIG_FEC2_PHY 4 +#define CONFIG_FEC2_PHY_NORXERR 1 + +#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */ + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_CMD_CDP + + +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_MISC_INIT_R + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ + +#define CONFIG_SYS_HUSH_PARSER 1 + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0300000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CONFIG_SYS_IMMR 0xFF000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0x40000000 +#if defined(DEBUG) +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#if CONFIG_NETPHONE_VERSION == 2 +#define CONFIG_SYS_FLASH_BASE4 0x40080000 +#endif + +#define CONFIG_SYS_RESET_ADDRESS 0x80000000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#if CONFIG_NETPHONE_VERSION == 1 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#elif CONFIG_NETPHONE_VERSION == 2 +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#endif +#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x10000 + +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000) +#define CONFIG_ENV_SIZE 0x4000 + +#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x70000) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + */ + +#if CONFIG_XIN == 10000000 + +#if MPC8XX_HZ == 120000000 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 100000000 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 50000000 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 25000000 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 40000000 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 75000000 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#else +#error unsupported CPU freq for XIN = 10MHz +#endif + +#elif CONFIG_XIN == 50000000 + +#if MPC8XX_HZ == 120000000 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 100000000 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 66666666 +#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#else +#error unsupported CPU freq for XIN = 50MHz +#endif + +#else + +#error unsupported XIN freq +#endif + + +/* + *----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + * + * Note: When TBS == 0 the timebase is independent of current cpu clock. + */ + +#define SCCR_MASK SCCR_EBDF11 +#if MPC8XX_HZ > 66666666 +#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00 | SCCR_EBDF01) +#else +#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) +#endif + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CONFIG_SYS_DER 0x2002000F*/ +#define CONFIG_SYS_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) + +#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) + +#if CONFIG_NETPHONE_VERSION == 2 + +#define FLASH_BASE4_PRELIM 0x40080000 /* FLASH bank #1 */ + +#define CONFIG_SYS_OR4_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_OR4_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_BR4_PRELIM ((FLASH_BASE4_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) + +#endif + +/* + * BR3 and OR3 (SDRAM) + * + */ +#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE (256 << 20) /* max 256MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CONFIG_SYS_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS) + +#define CONFIG_SYS_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM) +#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V) + +/* + * Memory Periodic Timer Prescaler + */ + +/* + * Memory Periodic Timer Prescaler + * + * The Divider for PTA (refresh timer) configuration is based on an + * example SDRAM configuration (64 MBit, one bank). The adjustment to + * the number of chip selects (NCS) and the actually needed refresh + * rate is done by setting MPTPR. + * + * PTA is calculated from + * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS) + * + * gclk CPU clock (not bus clock!) + * Trefresh Refresh cycle * 4 (four word bursts used) + * + * 4096 Rows from SDRAM example configuration + * 1000 factor s -> ms + * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + * -------------------------------------------- + * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 + * + * 50 MHz => 50.000.000 / Divider = 98 + * 66 Mhz => 66.000.000 / Divider = 129 + * 80 Mhz => 80.000.000 / Divider = 156 + */ + +#define CONFIG_SYS_MAMR_PTA 234 + +/* + * For 16 MBit, refresh rates could be 31.3 us + * (= 64 ms / 2K = 125 / quad bursts). + * For a simpler initialization, 15.6 us is used instead. + * + * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks + * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank + */ +#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +/* 9 column SDRAM */ +#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +#define CONFIG_LAST_STAGE_INIT /* needed to reset the damn phys */ + +/****************************************************************/ + +#define DSP_SIZE 0x00010000 /* 64K */ +#define NAND_SIZE 0x00010000 /* 64K */ + +#define DSP_BASE 0xF1000000 +#define NAND_BASE 0xF1010000 + +/*****************************************************************************/ + +#define CONFIG_SYS_DIRECT_FLASH_TFTP + +/*****************************************************************************/ + +#if CONFIG_NETPHONE_VERSION == 1 +#define STATUS_LED_BIT 0x00000008 /* bit 28 */ +#elif CONFIG_NETPHONE_VERSION == 2 +#define STATUS_LED_BIT 0x00000080 /* bit 24 */ +#endif + +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +#define STATUS_LED_STATE STATUS_LED_BLINKING + +#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ +#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +#ifndef __ASSEMBLY__ + +/* LEDs */ + +/* led_id_t is unsigned int mask */ +typedef unsigned int led_id_t; + +#define __led_toggle(_msk) \ + do { \ + ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat ^= (_msk); \ + } while(0) + +#define __led_set(_msk, _st) \ + do { \ + if ((_st)) \ + ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat |= (_msk); \ + else \ + ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat &= ~(_msk); \ + } while(0) + +#define __led_init(msk, st) __led_set(msk, st) + +#endif + +/*********************************************************************************************************** + + ---------------------------------------------------------------------------------------------- + + (V1) version 1 of the board + (V2) version 2 of the board + + ---------------------------------------------------------------------------------------------- + + Pin definitions: + + +------+----------------+--------+------------------------------------------------------------ + | # | Name | Type | Comment + +------+----------------+--------+------------------------------------------------------------ + | PA3 | SPIEN_MAX | Output | MAX serial to uart chip select + | PA7 | DSP_INT | Output | DSP interrupt + | PA10 | DSP_RESET | Output | DSP reset + | PA14 | USBOE | Output | USB (1) + | PA15 | USBRXD | Output | USB (1) + | PB19 | BT_RTS | Output | Bluetooth (0) + | PB23 | BT_CTS | Output | Bluetooth (0) + | PB26 | SPIEN_SEP | Output | Serial EEPROM chip select + | PB27 | SPICS_DISP | Output | Display chip select + | PB28 | SPI_RXD_3V | Input | SPI Data Rx + | PB29 | SPI_TXD | Output | SPI Data Tx + | PB30 | SPI_CLK | Output | SPI Clock + | PC10 | DISPA0 | Output | Display A0 + | PC11 | BACKLIGHT | Output | Display backlit + | PC12 | SPI2RXD | Input | (V1) 2nd SPI RXD + | | IO_RESET | Output | (V2) General I/O reset + | PC13 | SPI2TXD | Output | (V1) 2nd SPI TXD (V1) + | | HOOK | Input | (V2) Hook input interrupt + | PC15 | SPI2CLK | Output | (V1) 2nd SPI CLK + | | F_RY_BY | Input | (V2) NAND F_RY_BY + | PE17 | F_ALE | Output | NAND F_ALE + | PE18 | F_CLE | Output | NAND F_CLE + | PE20 | F_CE | Output | NAND F_CE + | PE24 | SPICS_SCOUT | Output | (V1) Codec chip select + | | LED | Output | (V2) LED + | PE27 | SPICS_ER | Output | External serial register CS + | PE28 | LEDIO1 | Output | (V1) LED + | | BKBR1 | Input | (V2) Keyboard input scan + | PE29 | LEDIO2 | Output | (V1) LED hook for A (TA2) + | | BKBR2 | Input | (V2) Keyboard input scan + | PE30 | LEDIO3 | Output | (V1) LED hook for A (TA2) + | | BKBR3 | Input | (V2) Keyboard input scan + | PE31 | F_RY_BY | Input | (V1) NAND F_RY_BY + | | BKBR4 | Input | (V2) Keyboard input scan + +------+----------------+--------+--------------------------------------------------- + + ---------------------------------------------------------------------------------------------- + + Serial register input: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | 0 | BKBR1 | (V1) Keyboard input scan + | 1 | BKBR3 | (V1) Keyboard input scan + | 2 | BKBR4 | (V1) Keyboard input scan + | 3 | BKBR2 | (V1) Keyboard input scan + | 4 | HOOK | (V1) Hook switch + | 5 | BT_LINK | (V1) Bluetooth link status + | 6 | HOST_WAKE | (V1) Bluetooth host wake up + | 7 | OK_ETH | (V1) Cisco inline power OK status + +------+----------------+------------------------------------------------------------ + + ---------------------------------------------------------------------------------------------- + + Serial register output: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | 0 | KEY1 | Keyboard output scan + | 1 | KEY2 | Keyboard output scan + | 2 | KEY3 | Keyboard output scan + | 3 | KEY4 | Keyboard output scan + | 4 | KEY5 | Keyboard output scan + | 5 | KEY6 | Keyboard output scan + | 6 | KEY7 | Keyboard output scan + | 7 | BT_WAKE | Bluetooth wake up + +------+----------------+------------------------------------------------------------ + + ---------------------------------------------------------------------------------------------- + + Chip selects: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | CS0 | CS0 | Boot flash + | CS1 | CS_FLASH | NAND flash + | CS2 | CS_DSP | DSP + | CS3 | DCS_DRAM | DRAM + | CS4 | CS_FLASH2 | (V2) 2nd flash + +------+----------------+------------------------------------------------------------ + + ---------------------------------------------------------------------------------------------- + + Interrupts: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | IRQ1 | IRQ_DSP | DSP interrupt + | IRQ3 | S_INTER | DUSLIC ??? + | IRQ4 | F_RY_BY | NAND + | IRQ7 | IRQ_MAX | MAX 3100 interrupt + +------+----------------+------------------------------------------------------------ + + ---------------------------------------------------------------------------------------------- + + Interrupts on PCMCIA pins: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | IP_A0| PHY1_LINK | Link status changed for #1 Ethernet interface + | IP_A1| PHY2_LINK | Link status changed for #2 Ethernet interface + | IP_A2| RMII1_MDINT | PHY interrupt for #1 + | IP_A3| RMII2_MDINT | PHY interrupt for #2 + | IP_A5| HOST_WAKE | (V2) Bluetooth host wake + | IP_A6| OK_ETH | (V2) Cisco inline power OK + +------+----------------+------------------------------------------------------------ + +*************************************************************************************************/ + +#define CONFIG_SED156X 1 /* use SED156X */ +#define CONFIG_SED156X_PG12864Q 1 /* type of display used */ + +/* serial interfacing macros */ + +#define SED156X_SPI_RXD_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) +#define SED156X_SPI_RXD_MASK 0x00000008 + +#define SED156X_SPI_TXD_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) +#define SED156X_SPI_TXD_MASK 0x00000004 + +#define SED156X_SPI_CLK_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) +#define SED156X_SPI_CLK_MASK 0x00000002 + +#define SED156X_CS_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) +#define SED156X_CS_MASK 0x00000010 + +#define SED156X_A0_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat) +#define SED156X_A0_MASK 0x0020 + +/*************************************************************************************************/ + +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE 1 +#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE 1 + +/*************************************************************************************************/ + +/* use board specific hardware */ +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_HW_WATCHDOG +#define CONFIG_SHOW_ACTIVITY + +/*************************************************************************************************/ + +/* phone console configuration */ + +#define PHONE_CONSOLE_POLL_HZ (CONFIG_SYS_HZ/200) /* poll every 5ms */ + +/*************************************************************************************************/ + +#define CONFIG_CDP_DEVICE_ID 20 +#define CONFIG_CDP_DEVICE_ID_PREFIX "NP" /* netphone */ +#define CONFIG_CDP_PORT_ID "eth%d" +#define CONFIG_CDP_CAPABILITIES 0x00000010 +#define CONFIG_CDP_VERSION "u-boot" " " U_BOOT_DATE " " U_BOOT_TIME +#define CONFIG_CDP_PLATFORM "Intracom NetPhone" +#define CONFIG_CDP_TRIGGER 0x20020001 +#define CONFIG_CDP_POWER_CONSUMPTION 4300 /* 90 mA @ 48V */ +#define CONFIG_CDP_APPLIANCE_VLAN_TYPE 0x01 /* ipphone */ + +/*************************************************************************************************/ + +#define CONFIG_AUTO_COMPLETE 1 + +/*************************************************************************************************/ + +#define CONFIG_CRC32_VERIFY 1 + +/*************************************************************************************************/ + +#define CONFIG_HUSH_OLD_PARSER_COMPATIBLE 1 + +/*************************************************************************************************/ +#endif /* __CONFIG_H */ -- cgit 1.2.3-korg