From e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb Mon Sep 17 00:00:00 2001 From: Yang Zhang Date: Fri, 28 Aug 2015 09:58:54 +0800 Subject: Add qemu 2.4.0 Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang --- qemu/roms/u-boot/doc/README.kwbimage | 104 +++++++++++++++++++++++++++++++++++ 1 file changed, 104 insertions(+) create mode 100644 qemu/roms/u-boot/doc/README.kwbimage (limited to 'qemu/roms/u-boot/doc/README.kwbimage') diff --git a/qemu/roms/u-boot/doc/README.kwbimage b/qemu/roms/u-boot/doc/README.kwbimage new file mode 100644 index 000000000..13f6f92f6 --- /dev/null +++ b/qemu/roms/u-boot/doc/README.kwbimage @@ -0,0 +1,104 @@ +--------------------------------------------- +Kirkwood Boot Image generation using mkimage +--------------------------------------------- + +This document describes the U-Boot feature as it +is implemented for the Kirkwood family of SoCs. + +The Kirkwood SoC's can boot directly from NAND FLASH, +SPI FLASH, SATA etc. using its internal bootRom support. + +for more details refer section 24.2 of Kirkwood functional specifications. +ref: www.marvell.com/products/embedded.../kirkwood/index.jsp + +Command syntax: +-------------- +./tools/mkimage -l + to list the kwb image file details + +./tools/mkimage -n \ + -T kwbimage -a -e \ + -d + +for ex. +./tools/mkimage -n ./board/Marvell/openrd_base/kwbimage.cfg \ + -T kwbimage -a 0x00600000 -e 0x00600000 \ + -d u-boot.bin u-boot.kwb + + +kwbimage support available with mkimage utility will generate kirkwood boot +image that can be flashed on the board NAND/SPI flash. The make target +which uses mkimage to produce such an image is "u-boot.kwb". For example: + + export BUILD_DIR=/tmp/build + make distclean + make yourboard_config + make $BUILD_DIR/u-boot.kwb + + +Board specific configuration file specifications: +------------------------------------------------ +1. This file must present in the $(BOARDDIR). The default name is + kwbimage.cfg. The name can be set as part of the full path + to the file using CONFIG_SYS_KWD_CONFIG (probably in + include/configs/.h). The path should look like: + $(CONFIG_BOARDDIR)/.cfg +2. This file can have empty lines and lines starting with "#" as first + character to put comments +3. This file can have configuration command lines as mentioned below, + any other information in this file is treated as invalid. + +Configuration command line syntax: +--------------------------------- +1. Each command line is must have two strings, first one command or address + and second one data string +2. Following are the valid command strings and associated data strings:- + Command string data string + -------------- ----------- + BOOT_FROM nand/spi/sata + NAND_ECC_MODE default/rs/hamming/disabled + NAND_PAGE_SIZE any uint16_t hex value + SATA_PIO_MODE any uint32_t hex value + DDR_INIT_DELAY any uint32_t hex value + DATA regaddr and regdara hex value + you can have maximum 55 such register programming commands + +3. All commands are optional to program + +Typical example of kwimage.cfg file: +----------------------------------- + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b1b9b +# DRAM Configuration +DATA 0xFFD01400 0x43000c30 +DATA 0xFFD01404 0x37543000 +DATA 0xFFD01408 0x22125451 +DATA 0xFFD0140C 0x00000a33 +DATA 0xFFD01410 0x000000cc +DATA 0xFFD01414 0x00000000 +DATA 0xFFD01418 0x00000000 +DATA 0xFFD0141C 0x00000C52 +DATA 0xFFD01420 0x00000040 +DATA 0xFFD01424 0x0000F17F +DATA 0xFFD01428 0x00085520 +DATA 0xFFD0147C 0x00008552 +DATA 0xFFD01504 0x0FFFFFF1 +DATA 0xFFD01508 0x10000000 +DATA 0xFFD0150C 0x0FFFFFF5 +DATA 0xFFD01514 0x00000000 +DATA 0xFFD0151C 0x00000000 +DATA 0xFFD01494 0x00030000 +DATA 0xFFD01498 0x00000000 +DATA 0xFFD0149C 0x0000E803 +DATA 0xFFD01480 0x00000001 +# End of Header extension +DATA 0x0 0x0 + +------------------------------------------------ +Author: Prafulla Wadaskar -- cgit 1.2.3-korg