From e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb Mon Sep 17 00:00:00 2001 From: Yang Zhang Date: Fri, 28 Aug 2015 09:58:54 +0800 Subject: Add qemu 2.4.0 Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang --- qemu/roms/u-boot/board/xes/xpedite550x/Makefile | 10 ++ qemu/roms/u-boot/board/xes/xpedite550x/ddr.c | 136 +++++++++++++++++++++ qemu/roms/u-boot/board/xes/xpedite550x/law.c | 26 ++++ qemu/roms/u-boot/board/xes/xpedite550x/tlb.c | 82 +++++++++++++ .../u-boot/board/xes/xpedite550x/xpedite550x.c | 82 +++++++++++++ 5 files changed, 336 insertions(+) create mode 100644 qemu/roms/u-boot/board/xes/xpedite550x/Makefile create mode 100644 qemu/roms/u-boot/board/xes/xpedite550x/ddr.c create mode 100644 qemu/roms/u-boot/board/xes/xpedite550x/law.c create mode 100644 qemu/roms/u-boot/board/xes/xpedite550x/tlb.c create mode 100644 qemu/roms/u-boot/board/xes/xpedite550x/xpedite550x.c (limited to 'qemu/roms/u-boot/board/xes/xpedite550x') diff --git a/qemu/roms/u-boot/board/xes/xpedite550x/Makefile b/qemu/roms/u-boot/board/xes/xpedite550x/Makefile new file mode 100644 index 000000000..1a3fe7635 --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite550x/Makefile @@ -0,0 +1,10 @@ +# +# Copyright 2007-2008 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += xpedite550x.o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/qemu/roms/u-boot/board/xes/xpedite550x/ddr.c b/qemu/roms/u-boot/board/xes/xpedite550x/ddr.c new file mode 100644 index 000000000..0c0605e3a --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite550x/ddr.c @@ -0,0 +1,136 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include + +#include +#include + +void get_spd(ddr3_spd_eeprom_t *spd, u8 i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr3_spd_eeprom_t)); +} + +/* + * There are traditionally three board-specific SDRAM timing parameters + * which must be calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 3.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * ====== XPedite550x DDR3-800 read delay calculations ====== + * + * The P2020 processor provides an autoleveling option. Setting CPO to + * 0x1f enables this auto configuration. + */ + +typedef struct { + unsigned short datarate_mhz_low; + unsigned short datarate_mhz_high; + unsigned char clk_adjust; + unsigned char cpo; +} board_specific_parameters_t; + +const board_specific_parameters_t board_specific_parameters[][20] = { + { + /* Controller 0 */ + { + /* DDR3-600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo = 31, + }, + { + /* DDR3-800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo = 31, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const board_specific_parameters_t *pbsp = + &(board_specific_parameters[ctrl_num][0]); + u32 num_params = sizeof(board_specific_parameters[ctrl_num]) / + sizeof(board_specific_parameters[0][0]); + u32 i; + ulong ddr_freq; + + /* + * Set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in + * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If + * there are two dimms in the controller, set odt_rd_cfg to 3 and + * odt_wr_cfg to 3 for the even CS, 0 for the odd CS. + */ + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i&1) { /* odd CS */ + popts->cs_local_opts[i].odt_rd_cfg = 0; + popts->cs_local_opts[i].odt_wr_cfg = 0; + } else { /* even CS */ + if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) { + popts->cs_local_opts[i].odt_rd_cfg = 0; + popts->cs_local_opts[i].odt_wr_cfg = 4; + } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) { + popts->cs_local_opts[i].odt_rd_cfg = 3; + popts->cs_local_opts[i].odt_wr_cfg = 3; + } + } + } + + /* + * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + + for (i = 0; i < num_params; i++) { + if (ddr_freq >= pbsp->datarate_mhz_low && + ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->cpo_override = pbsp->cpo; + popts->twot_en = 0; + break; + } + pbsp++; + } + + if (i == num_params) { + printf("Warning: board specific timing not found " + "for data rate %lu MT/s!\n", ddr_freq); + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + + /* + * Enable on-die termination. + * From the Micron Technical Node TN-41-04, RTT_Nom should typically + * be 30 to 40 ohms, while RTT_WR should be 120 ohms. Setting RTT_WR + * is handled in the Freescale DDR3 driver. Set RTT_Nom here. + */ + popts->rtt_override = 1; + popts->rtt_override_value = 3; +} diff --git a/qemu/roms/u-boot/board/xes/xpedite550x/law.c b/qemu/roms/u-boot/board/xes/xpedite550x/law.c new file mode 100644 index 000000000..1a3e91b90 --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite550x/law.c @@ -0,0 +1,26 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/qemu/roms/u-boot/board/xes/xpedite550x/tlb.c b/qemu/roms/u-boot/board/xes/xpedite550x/tlb.c new file mode 100644 index 000000000..0bcb93069 --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite550x/tlb.c @@ -0,0 +1,82 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + + /* **M** - Boot page for secondary processors */ + SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, + 0, 3, BOOKE_PAGESZ_4K, 1), + +#ifdef CONFIG_PCIE1 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1G, 1), +#endif + +#ifdef CONFIG_PCIE2 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), +#endif + +#ifdef CONFIG_PCIE3 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_64M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/qemu/roms/u-boot/board/xes/xpedite550x/xpedite550x.c b/qemu/roms/u-boot/board/xes/xpedite550x/xpedite550x.c new file mode 100644 index 000000000..e64d682af --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite550x/xpedite550x.c @@ -0,0 +1,82 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +static void flash_cs_fixup(void) +{ + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS)); + printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + set_lbc_br(0, CONFIG_SYS_BR1_PRELIM); + set_lbc_or(0, CONFIG_SYS_OR1_PRELIM); + + set_lbc_br(1, CONFIG_SYS_BR0_PRELIM); + set_lbc_or(1, CONFIG_SYS_OR0_PRELIM); + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif -- cgit 1.2.3-korg