From e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb Mon Sep 17 00:00:00 2001 From: Yang Zhang Date: Fri, 28 Aug 2015 09:58:54 +0800 Subject: Add qemu 2.4.0 Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang --- qemu/roms/u-boot/board/csb272/Makefile | 9 ++ qemu/roms/u-boot/board/csb272/csb272.c | 171 ++++++++++++++++++++++++++++ qemu/roms/u-boot/board/csb272/init.S | 196 +++++++++++++++++++++++++++++++++ 3 files changed, 376 insertions(+) create mode 100644 qemu/roms/u-boot/board/csb272/Makefile create mode 100644 qemu/roms/u-boot/board/csb272/csb272.c create mode 100644 qemu/roms/u-boot/board/csb272/init.S (limited to 'qemu/roms/u-boot/board/csb272') diff --git a/qemu/roms/u-boot/board/csb272/Makefile b/qemu/roms/u-boot/board/csb272/Makefile new file mode 100644 index 000000000..36ec9b6f4 --- /dev/null +++ b/qemu/roms/u-boot/board/csb272/Makefile @@ -0,0 +1,9 @@ +# +# (C) Copyright 2000-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y = csb272.o +obj-y += init.o diff --git a/qemu/roms/u-boot/board/csb272/csb272.c b/qemu/roms/u-boot/board/csb272/csb272.c new file mode 100644 index 000000000..dc2c9503e --- /dev/null +++ b/qemu/roms/u-boot/board/csb272/csb272.c @@ -0,0 +1,171 @@ +/* + * (C) Copyright 2004 + * Tolunay Orkun, Nextio Inc., torkun@nextio.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include + +void sdram_init(void); + +/* + * Configuration data for AMIS FS6377-01 Programmable 3-PLL Clock Generator + * + * CLKA output => Epson LCD Controller + * CLKB output => Not Connected + * CLKC output => Ethernet + * CLKD output => UART external clock + * + * Note: these values are obtained from device after init by micromonitor +*/ +uchar pll_fs6377_regs[16] = { + 0x28, 0xef, 0x53, 0x03, 0x4b, 0x80, 0x32, 0x80, + 0x94, 0x32, 0x80, 0xd4, 0x56, 0xf6, 0xf6, 0xe0 }; + +/* + * pll_init: Initialize AMIS IC FS6377-01 PLL + * + * PLL supplies Epson LCD Clock, Ethernet Clock and UART external clock + * + */ +int pll_init(void) +{ + i2c_set_bus_num(0); + + return i2c_write(CONFIG_SYS_I2C_PLL_ADDR, 0, 1, + (uchar *) pll_fs6377_regs, sizeof(pll_fs6377_regs)); +} + +/* + * board_early_init_f: do early board initialization + * + */ +int board_early_init_f(void) +{ + /* initialize PLL so UART, LCD, Ethernet clocked at correctly */ + (void) get_clocks(); + pll_init(); + + /*-------------------------------------------------------------------------+ + | Interrupt controller setup for the Walnut board. + | Note: IRQ 0-15 405GP internally generated; active high; level sensitive + | IRQ 16 405GP internally generated; active low; level sensitive + | IRQ 17-24 RESERVED + | IRQ 25 (EXT IRQ 0) FPGA; active high; level sensitive + | IRQ 26 (EXT IRQ 1) SMI; active high; level sensitive + | IRQ 27 (EXT IRQ 2) Not Used + | IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive + | IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive + | IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive + | IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive + | Note for Walnut board: + | An interrupt taken for the FPGA (IRQ 25) indicates that either + | the Mouse, Keyboard, IRDA, or External Expansion caused the + | interrupt. The FPGA must be read to determine which device + | caused the interrupt. The default setting of the FPGA clears + | + +-------------------------------------------------------------------------*/ + + mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ + mtdcr (UIC0ER, 0x00000000); /* disable all ints */ + mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */ + mtdcr (UIC0PR, 0xFFFFFF83); /* set int polarities */ + mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */ + mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */ + mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ + + mtebc (EBC0_CFG, 0xa8400000); /* EBC always driven */ + + return 0; /* success */ +} + +/* + * checkboard: identify/verify the board we are running + * + * Remark: we just assume it is correct board here! + * + */ +int checkboard(void) +{ + printf("BOARD: Cogent CSB272\n"); + + return 0; /* success */ +} + +/* + * initram: Determine the size of mounted DRAM + * + * Size is determined by reading SDRAM configuration registers as + * configured by initialization code + * + */ +phys_size_t initdram (int board_type) +{ + ulong tot_size; + ulong bank_size; + ulong tmp; + + /* + * ToDo: Move the asm init routine sdram_init() to this C file, + * or even better use some common ppc4xx code available + * in arch/powerpc/cpu/ppc4xx + */ + sdram_init(); + + tot_size = 0; + + mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR); + tmp = mfdcr (SDRAM0_CFGDATA); + if (tmp & 0x00000001) { + bank_size = 0x00400000 << ((tmp >> 17) & 0x7); + tot_size += bank_size; + } + + mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR); + tmp = mfdcr (SDRAM0_CFGDATA); + if (tmp & 0x00000001) { + bank_size = 0x00400000 << ((tmp >> 17) & 0x7); + tot_size += bank_size; + } + + mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR); + tmp = mfdcr (SDRAM0_CFGDATA); + if (tmp & 0x00000001) { + bank_size = 0x00400000 << ((tmp >> 17) & 0x7); + tot_size += bank_size; + } + + mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR); + tmp = mfdcr (SDRAM0_CFGDATA); + if (tmp & 0x00000001) { + bank_size = 0x00400000 << ((tmp >> 17) & 0x7); + tot_size += bank_size; + } + + return tot_size; +} + +/* + * last_stage_init: final configurations (such as PHY etc) + * + */ +int last_stage_init(void) +{ + /* initialize the PHY */ + miiphy_reset("ppc_4xx_eth0", CONFIG_PHY_ADDR); + + /* AUTO neg */ + miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_BMCR, + BMCR_ANENABLE | BMCR_ANRESTART); + + /* LEDs */ + miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_NWAYTEST, 0x0d08); + + + return 0; /* success */ +} diff --git a/qemu/roms/u-boot/board/csb272/init.S b/qemu/roms/u-boot/board/csb272/init.S new file mode 100644 index 000000000..bf1d98680 --- /dev/null +++ b/qemu/roms/u-boot/board/csb272/init.S @@ -0,0 +1,196 @@ +/* + * SPDX-License-Identifier: GPL-2.0 IBM-pibs + */ +#include +#include + +#include +#include + +#include +#include + +#define LI32(reg,val) \ + addis reg,0,val@h;\ + ori reg,reg,val@l + +#define WDCR_EBC(reg,val) \ + addi r4,0,reg;\ + mtdcr EBC0_CFGADDR,r4;\ + addis r4,0,val@h;\ + ori r4,r4,val@l;\ + mtdcr EBC0_CFGDATA,r4 + +#define WDCR_SDRAM(reg,val) \ + addi r4,0,reg;\ + mtdcr SDRAM0_CFGADDR,r4;\ + addis r4,0,val@h;\ + ori r4,r4,val@l;\ + mtdcr SDRAM0_CFGDATA,r4 + +/****************************************************************************** + * Function: ext_bus_cntlr_init + * + * Description: Configures EBC Controller and a few basic chip selects. + * + * CS0 is setup to get the Boot Flash out of the addresss range + * so that we may setup a stack. CS7 is setup so that we can + * access and reset the hardware watchdog. + * + * IMPORTANT: For pass1 this code must run from + * cache since you can not reliably change a peripheral banks + * timing register (pbxap) while running code from that bank. + * For ex., since we are running from ROM on bank 0, we can NOT + * execute the code that modifies bank 0 timings from ROM, so + * we run it from cache. + * + * Notes: Does NOT use the stack. + *****************************************************************************/ + .section ".text" + .align 2 + .globl ext_bus_cntlr_init + .type ext_bus_cntlr_init, @function +ext_bus_cntlr_init: + mflr r0 + /******************************************************************** + * Prefetch entire ext_bus_cntrl_init function into the icache. + * This is necessary because we are going to change the same CS we + * are executing from. Otherwise a CPU lockup may occur. + *******************************************************************/ + bl ..getAddr +..getAddr: + mflr r3 /* get address of ..getAddr */ + + /* Calculate number of cache lines for this function */ + addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2) + mtctr r4 +..ebcloop: + icbt r0, r3 /* prefetch cache line for addr in r3*/ + addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */ + bdnz ..ebcloop /* continue for $CTR cache lines */ + + /******************************************************************** + * Delay to ensure all accesses to ROM are complete before changing + * bank 0 timings. 200usec should be enough. + * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles. + *******************************************************************/ + addis r3, 0, 0x0 + ori r3, r3, 0xA000 /* wait 200us from reset */ + mtctr r3 +..spinlp: + bdnz ..spinlp /* spin loop */ + + /******************************************************************** + * SETUP CPC0_CR0 + *******************************************************************/ + LI32(r4, 0x007000c0) + mtdcr CPC0_CR0, r4 + + /******************************************************************** + * Setup CPC0_CR1: Change PCIINT signal to PerWE + *******************************************************************/ + mfdcr r4, CPC0_CR1 + ori r4, r4, 0x4000 + mtdcr CPC0_CR1, r4 + + /******************************************************************** + * Setup External Bus Controller (EBC). + *******************************************************************/ + WDCR_EBC(EBC0_CFG, 0xd84c0000) + /******************************************************************** + * Memory Bank 0 (Intel 28F128J3 Flash) initialization + *******************************************************************/ + /*WDCR_EBC(PB1AP, 0x02869200)*/ + WDCR_EBC(PB1AP, 0x07869200) + WDCR_EBC(PB0CR, 0xfe0bc000) + /******************************************************************** + * Memory Bank 1 (Holtek HT6542B PS/2) initialization + *******************************************************************/ + WDCR_EBC(PB1AP, 0x1f869200) + WDCR_EBC(PB1CR, 0xf0818000) + /******************************************************************** + * Memory Bank 2 (Epson S1D13506) initialization + *******************************************************************/ + WDCR_EBC(PB2AP, 0x05860300) + WDCR_EBC(PB2CR, 0xf045a000) + /******************************************************************** + * Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization + *******************************************************************/ + WDCR_EBC(PB3AP, 0x0387d200) + WDCR_EBC(PB3CR, 0xf021c000) + /******************************************************************** + * Memory Bank 4-7 (Unused) initialization + *******************************************************************/ + WDCR_EBC(PB4AP, 0) + WDCR_EBC(PB4CR, 0) + WDCR_EBC(PB5AP, 0) + WDCR_EBC(PB5CR, 0) + WDCR_EBC(PB6AP, 0) + WDCR_EBC(PB6CR, 0) + WDCR_EBC(PB7AP, 0) + WDCR_EBC(PB7CR, 0) + + /* We are all done */ + mtlr r0 /* Restore link register */ + blr /* Return to calling function */ +.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init +/* end ext_bus_cntlr_init() */ + +/****************************************************************************** + * Function: sdram_init + * + * Description: Configures SDRAM memory banks. + * + * Notes: Does NOT use the stack. + *****************************************************************************/ + .section ".text" + .align 2 + .globl sdram_init + .type sdram_init, @function +sdram_init: + + /* + * Disable memory controller to allow + * values to be changed. + */ + WDCR_SDRAM(SDRAM0_CFG, 0x00000000) + + /* + * Configure Memory Banks + */ + WDCR_SDRAM(SDRAM0_B0CR, 0x00084001) + WDCR_SDRAM(SDRAM0_B1CR, 0x00000000) + WDCR_SDRAM(SDRAM0_B2CR, 0x00000000) + WDCR_SDRAM(SDRAM0_B3CR, 0x00000000) + + /* + * Set up SDTR1 (SDRAM Timing Register) + */ + WDCR_SDRAM(SDRAM0_TR, 0x00854009) + + /* + * Set RTR (Refresh Timing Register) + */ + WDCR_SDRAM(SDRAM0_RTR, 0x10000000) + /* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */ + + /******************************************************************** + * Delay to ensure 200usec have elapsed since reset. Assume worst + * case that the core is running 200Mhz: + * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles + *******************************************************************/ + addis r3, 0, 0x0000 + ori r3, r3, 0xA000 /* Wait >200us from reset */ + mtctr r3 +..spinlp2: + bdnz ..spinlp2 /* spin loop */ + + /******************************************************************** + * Set memory controller options reg, MCOPT1. + *******************************************************************/ + WDCR_SDRAM(SDRAM0_CFG,0x80800000) + +..sdri_done: + blr /* Return to calling function */ +.Lfe1: .size sdram_init,.Lfe1-sdram_init +/* end sdram_init() */ -- cgit 1.2.3-korg