From e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb Mon Sep 17 00:00:00 2001 From: Yang Zhang Date: Fri, 28 Aug 2015 09:58:54 +0800 Subject: Add qemu 2.4.0 Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang --- qemu/roms/u-boot/board/buffalo/lsxl/Makefile | 8 + .../u-boot/board/buffalo/lsxl/kwbimage-lschl.cfg | 213 +++++++++++++++ .../u-boot/board/buffalo/lsxl/kwbimage-lsxhl.cfg | 213 +++++++++++++++ qemu/roms/u-boot/board/buffalo/lsxl/lsxl.c | 290 +++++++++++++++++++++ qemu/roms/u-boot/board/buffalo/lsxl/lsxl.h | 59 +++++ 5 files changed, 783 insertions(+) create mode 100644 qemu/roms/u-boot/board/buffalo/lsxl/Makefile create mode 100644 qemu/roms/u-boot/board/buffalo/lsxl/kwbimage-lschl.cfg create mode 100644 qemu/roms/u-boot/board/buffalo/lsxl/kwbimage-lsxhl.cfg create mode 100644 qemu/roms/u-boot/board/buffalo/lsxl/lsxl.c create mode 100644 qemu/roms/u-boot/board/buffalo/lsxl/lsxl.h (limited to 'qemu/roms/u-boot/board/buffalo/lsxl') diff --git a/qemu/roms/u-boot/board/buffalo/lsxl/Makefile b/qemu/roms/u-boot/board/buffalo/lsxl/Makefile new file mode 100644 index 000000000..1b01b4018 --- /dev/null +++ b/qemu/roms/u-boot/board/buffalo/lsxl/Makefile @@ -0,0 +1,8 @@ +# +# Copyright (c) 2012 Michael Walle +# Michael Walle +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := lsxl.o diff --git a/qemu/roms/u-boot/board/buffalo/lsxl/kwbimage-lschl.cfg b/qemu/roms/u-boot/board/buffalo/lsxl/kwbimage-lschl.cfg new file mode 100644 index 000000000..5fc122f13 --- /dev/null +++ b/qemu/roms/u-boot/board/buffalo/lsxl/kwbimage-lschl.cfg @@ -0,0 +1,213 @@ +# +# Copyright (c) 2012 Michael Walle +# Michael Walle +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0/1 interface pad voltage to 1.8V +DATA 0xFFD100E0 0x1B1B1B9B + +# L2 RAM Timing 0 +DATA 0xFFD20134 0xBBBBBBBB +# not further specified in HW manual, timing taken from original vendor port + +# L2 RAM Timing 1 +DATA 0xFFD20138 0x00BBBBBB +# not further specified in HW manual, timing taken from original vendor port + +# DDR Configuration register +DATA 0xFFD01400 0x43000618 +# bit13-0: 0x618, 1560 DDR2 clks refresh rate +# bit23-14: 0 required +# bit24: 1, enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: 0 required +# bit31-30: 0b01 required + +# DDR Controller Control Low +DATA 0xFFD01404 0x39543000 +# bit3-0: 0 required +# bit4: 0, addr/cmd in same cycle +# bit5: 0, clk is driven during self refresh, we don't care for APX +# bit6: 0, use recommended falling edge of clk for addr/cmd +# bit11-7: 0 required +# bit12: 1 required +# bit13: 1 required +# bit14: 0, input buffer always powered up +# bit17-15: 0 required +# bit18: 1, cpu lock transaction enabled +# bit19: 0 required +# bit23-20: 5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 9, CL+4, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0, no additional STARTBURST delay + +# DDR Timing (Low) +DATA 0xFFD01408 0x3302444F +# bit3-0: 0xf, 16 cycle tRAS (tRAS[3-0]) +# bit7-4: 4, 5 cycle tRCD +# bit11-8: 4, 5 cyle tRP +# bit15-12: 4, 5 cyle tWR +# bit19-16: 2, 3 cyle tWTR +# bit20: 0, 16 cycle tRAS (tRAS[4]) +# bit23-21: 0 required +# bit27-24: 3, 4 cycle tRRD +# bit31-28: 3, 4 cyle tRTP + +# DDR Timing (High) +DATA 0xFFD0140C 0x00000823 +# bit6-0: 0x23, 35 cycle tRFC +# bit8-7: 0, 1 cycle tR2R +# bit10-9: 0, 1 cyle tR2W +# bit12-11: 1, 2 cylce tW2W +# bit31-13: 0 required + +# DDR Address Control +DATA 0xFFD01410 0x00000009 +# bit1-0: 1, Cs0width=x16 +# bit3-2: 2, Cs0size=512Mbit +# bit5-4: 0, Cs1width=nonexistent +# bit7-6: 0, Cs1size=nonexistent +# bit9-8: 0, Cs2width=nonexistent +# bit11-10: 0, Cs2size=nonexistent +# bit13-12: 0, Cs3width=nonexistent +# bit15-14: 0, Cs3size=nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +# DDR Open Pages Control +DATA 0xFFD01414 0x00000000 +# bit0: 0, OPEn=OpenPage enabled +# bit31-1: 0 required + +# DDR Operation +DATA 0xFFD01418 0x00000000 +# bit3-0: 0, Cmd=Normal SDRAM Mode +# bit31-4: 0 required + +# DDR Mode +DATA 0xFFD0141C 0x00000652 +# bit2-0: 2, Burst Length (2 required) +# bit3: 0, Burst Type (0 required) +# bit6-4: 5, CAS Latency (CL) 5 +# bit7: 0, (Test Mode) Normal operation +# bit8: 0, (Reset DLL) Normal operation +# bit11-9: 3, Write recovery for auto-precharge (3 required) +# bit12: 0, Fast Active power down exit time (0 required) +# bit31-13: 0 required + +# DDR Extended Mode +DATA 0xFFD01420 0x00000042 +# bit0: 0, DRAM DLL enabled +# bit1: 1, DRAM drive strength reduced +# bit2: 0, ODT control Rtt[0] (Rtt=2, 150 ohm termination) +# bit5-3: 0 required +# bit6: 1, ODT control Rtt[1] (Rtt=2, 150 ohm termination) +# bit9-7: 0 required +# bit10: 0, differential DQS enabled +# bit11: 0 required +# bit12: 0, DRAM output buffer enabled +# bit31-13: 0 required + +# DDR Controller Control High +DATA 0xFFD01424 0x0000F17F +# bit2-0: 0x7 required +# bit3: 1, MBUS Burst Chop disabled +# bit6-4: 0x7 required +# bit7: 0 required (???) +# bit8: 1, add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9: 0, no half clock cycle addition to dataout +# bit10: 0, 1/4 clock cycle skew enabled for addr/ctl signals +# bit11: 0, 1/4 clock cycle skew disabled for write mesh +# bit15-12: 0xf required +# bit31-16: 0 required + +# DDR2 ODT Read Timing (default values) +DATA 0xFFD01428 0x00085520 +# bit3-0: 0 required +# bit7-4: 2, 2 cycles from read command to assertion of M_ODT signal +# bit11-8: 5, 5 cycles from read command to de-assertion of M_ODT signal +# bit15-12: 5, 5 cycles from read command to assertion of internal ODT signal +# bit19-16: 8, 8 cycles from read command to de-assertion of internal ODT signal +# bit31-20: 0 required + +# DDR2 ODT Write Timing (default values) +DATA 0xFFD0147C 0x00008552 +# bit3-0: 2, 2 cycles from write comand to assertion of M_ODT signal +# bit7-4: 5, 5 cycles from write command to de-assertion of M_ODT signal +# bit15-12: 5, 5 cycles from write command to assertion of internal ODT signal +# bit19-16: 8, 8 cycles from write command to de-assertion of internal ODT signal +# bit31-16: 0 required + +# CS[0]n Base address +DATA 0xFFD01500 0x00000000 +# at 0x0 + +# CS[0]n Size +DATA 0xFFD01504 0x03FFFFF1 +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 0x0, CS0 hit selected +# bit23-4: 0xfffff required +# bit31-24: 0x03, Size (i.e. 64MB) + +# CS[1]n Size +DATA 0xFFD0150C 0x00000000 +# window disabled + +# CS[2]n Size +DATA 0xFFD01514 0x00000000 +# window disabled + +# CS[3]n Size +DATA 0xFFD0151C 0x00000000 +# window disabled + +# DDR ODT Control (Low) +DATA 0xFFD01494 0x003C0000 +# bit3-0: 0b0000, (read) M_ODT[0] is not asserted during read from DRAM +# bit7-4: 0b0000, (read) M_ODT[1] is not asserted during read from DRAM +# bit15-8: 0 required +# bit19-16: 0b1100, (write) M_ODT[0] is asserted during write to DRAM CS2, CS3 +# bit23-20: 0b0011, (write) M_ODT[1] is asserted during write to DRAM CS0, CS1 +# bit31-24: 0 required + +# DDR ODT Control (High) +DATA 0xFFD01498 0x00000000 +# bit1-0: 0, M_ODT[0] assertion is controlled by ODT Control Low register +# bit3-2: 0, M_ODT[1] assertion is controlled by ODT Control Low register +# bit31-4 0 required + +# CPU ODT Control +DATA 0xFFD0149C 0x0000E80F +# bit3-0: 0b1111, internal ODT is asserted during read from DRAM bank 0-3 +# bit7-4: 0b0000, internal ODT is not asserted during write to DRAM bank 0-3 +# bit9-8: 0, Internal ODT assertion is controlled by fiels +# bit11-10: 2, M_DQ, M_DM, and M_DQS I/O buffer ODT 75 ohm +# bit13-12: 2, M_STARTBURST_IN I/O buffer ODT 75 ohm +# bit14: 1, M_STARTBURST_IN ODT enabled +# bit15: 1, DDR IO ODT Unit: Drive ODT calibration values +# bit20-16: 0, Pad N channel driving strength for ODT +# bit25-21: 0, Pad P channel driving strength for ODT +# bit31-26: 0 required + +# DDR Initialization Control +DATA 0xFFD01480 0x00000001 +# bit0: 1, enable DDR init upon this register write +# bit31-1: 0, required + +# End of Header extension +DATA 0x0 0x0 diff --git a/qemu/roms/u-boot/board/buffalo/lsxl/kwbimage-lsxhl.cfg b/qemu/roms/u-boot/board/buffalo/lsxl/kwbimage-lsxhl.cfg new file mode 100644 index 000000000..80e2c0244 --- /dev/null +++ b/qemu/roms/u-boot/board/buffalo/lsxl/kwbimage-lsxhl.cfg @@ -0,0 +1,213 @@ +# +# Copyright (c) 2012 Michael Walle +# Michael Walle +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0/1 interface pad voltage to 1.8V +DATA 0xFFD100E0 0x1B1B9B9B + +# L2 RAM Timing 0 +DATA 0xFFD20134 0xBBBBBBBB +# not further specified in HW manual, timing taken from original vendor port + +# L2 RAM Timing 1 +DATA 0xFFD20138 0x00BBBBBB +# not further specified in HW manual, timing taken from original vendor port + +# DDR Configuration register +DATA 0xFFD01400 0x43000618 +# bit13-0: 0x618, 1560 DDR2 clks refresh rate +# bit23-14: 0 required +# bit24: 1, enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: 0 required +# bit31-30: 0b01 required + +# DDR Controller Control Low +DATA 0xFFD01404 0x39543010 +# bit3-0: 0 required +# bit4: 1, T2 mode, addr/cmd are driven for two cycles +# bit5: 0, clk is driven during self refresh, we don't care for APX +# bit6: 0, use recommended falling edge of clk for addr/cmd +# bit11-7: 0 required +# bit12: 1 required +# bit13: 1 required +# bit14: 0, input buffer always powered up +# bit17-15: 0 required +# bit18: 1, cpu lock transaction enabled +# bit19: 0 required +# bit23-20: 5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 9, CL+4, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0, no additional STARTBURST delay + +# DDR Timing (Low) +DATA 0xFFD01408 0x22125441 +# bit3-0: 0x1, 18 cycle tRAS (tRAS[3-0]) +# bit7-4: 4, 5 cycle tRCD +# bit11-8: 4, 5 cyle tRP +# bit15-12: 5, 6 cyle tWR +# bit19-16: 2, 3 cyle tWTR +# bit20: 1, 18 cycle tRAS (tRAS[4]) +# bit23-21: 0 required +# bit27-24: 2, 3 cycle tRRD +# bit31-28: 2, 3 cyle tRTP + +# DDR Timing (High) +DATA 0xFFD0140C 0x00000832 +# bit6-0: 0x32, 50 cycle tRFC +# bit8-7: 0, 1 cycle tR2R +# bit10-9: 0, 1 cyle tR2W +# bit12-11: 1, 2 cylce tW2W +# bit31-13: 0 required + +# DDR Address Control +DATA 0xFFD01410 0x0000000C +# bit1-0: 0, Cs0width=x8 +# bit3-2: 3, Cs0size=1Gbit +# bit5-4: 0, Cs1width=nonexistent +# bit7-6: 0, Cs1size=nonexistent +# bit9-8: 0, Cs2width=nonexistent +# bit11-10: 0, Cs2size=nonexistent +# bit13-12: 0, Cs3width=nonexistent +# bit15-14: 0, Cs3size=nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +# DDR Open Pages Control +DATA 0xFFD01414 0x00000000 +# bit0: 0, OPEn=OpenPage enabled +# bit31-1: 0 required + +# DDR Operation +DATA 0xFFD01418 0x00000000 +# bit3-0: 0, Cmd=Normal SDRAM Mode +# bit31-4: 0 required + +# DDR Mode +DATA 0xFFD0141C 0x00000652 +# bit2-0: 2, Burst Length (2 required) +# bit3: 0, Burst Type (0 required) +# bit6-4: 5, CAS Latency (CL) 5 +# bit7: 0, (Test Mode) Normal operation +# bit8: 0, (Reset DLL) Normal operation +# bit11-9: 3, Write recovery for auto-precharge (3 required) +# bit12: 0, Fast Active power down exit time (0 required) +# bit31-13: 0 required + +# DDR Extended Mode +DATA 0xFFD01420 0x00000006 +# bit0: 0, DRAM DLL enabled +# bit1: 1, DRAM drive strength reduced +# bit2: 1, ODT control Rtt[0] (Rtt=1, 75 ohm termination) +# bit5-3: 0 required +# bit6: 0, ODT control Rtt[1] (Rtt=1, 75 ohm termination) +# bit9-7: 0 required +# bit10: 0, differential DQS enabled +# bit11: 0 required +# bit12: 0, DRAM output buffer enabled +# bit31-13: 0 required + +# DDR Controller Control High +DATA 0xFFD01424 0x0000F17F +# bit2-0: 0x7 required +# bit3: 1, MBUS Burst Chop disabled +# bit6-4: 0x7 required +# bit7: 0 required (???) +# bit8: 1, add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9: 0, no half clock cycle addition to dataout +# bit10: 0, 1/4 clock cycle skew enabled for addr/ctl signals +# bit11: 0, 1/4 clock cycle skew disabled for write mesh +# bit15-12: 0xf required +# bit31-16: 0 required + +# DDR2 ODT Read Timing (default values) +DATA 0xFFD01428 0x00085520 +# bit3-0: 0 required +# bit7-4: 2, 2 cycles from read command to assertion of M_ODT signal +# bit11-8: 5, 5 cycles from read command to de-assertion of M_ODT signal +# bit15-12: 5, 5 cycles from read command to assertion of internal ODT signal +# bit19-16: 8, 8 cycles from read command to de-assertion of internal ODT signal +# bit31-20: 0 required + +# DDR2 ODT Write Timing (default values) +DATA 0xFFD0147C 0x00008552 +# bit3-0: 2, 2 cycles from write comand to assertion of M_ODT signal +# bit7-4: 5, 5 cycles from write command to de-assertion of M_ODT signal +# bit15-12: 5, 5 cycles from write command to assertion of internal ODT signal +# bit19-16: 8, 8 cycles from write command to de-assertion of internal ODT signal +# bit31-16: 0 required + +# CS[0]n Base address +DATA 0xFFD01500 0x00000000 +# at 0x0 + +# CS[0]n Size +DATA 0xFFD01504 0x0FFFFFF1 +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 0x0, CS0 hit selected +# bit23-4: 0xfffff required +# bit31-24: 0x0f, Size (i.e. 256MB) + +# CS[1]n Size +DATA 0xFFD0150C 0x00000000 +# window disabled + +# CS[2]n Size +DATA 0xFFD01514 0x00000000 +# window disabled + +# CS[3]n Size +DATA 0xFFD0151C 0x00000000 +# window disabled + +# DDR ODT Control (Low) +DATA 0xFFD01494 0x00010000 +# bit3-0: 0b0000, (read) M_ODT[0] is not asserted during read from DRAM +# bit7-4: 0b0000, (read) M_ODT[1] is not asserted during read from DRAM +# bit15-8: 0 required +# bit19-16: 0b0001, (write) M_ODT[0] is asserted during write to DRAM CS0 +# bit23-20: 0b0000, (write) M_ODT[1] is not asserted during write to DRAM +# bit31-24: 0 required + +# DDR ODT Control (High) +DATA 0xFFD01498 0x00000000 +# bit1-0: 0, M_ODT[0] assertion is controlled by ODT Control Low register +# bit3-2: 0, M_ODT[1] assertion is controlled by ODT Control Low register +# bit31-4 0 required + +# CPU ODT Control +DATA 0xFFD0149C 0x0000E80F +# bit3-0: 0b1111, internal ODT is asserted during read from DRAM bank 0-3 +# bit7-4: 0b0000, internal ODT is not asserted during write to DRAM bank 0-3 +# bit9-8: 0, Internal ODT assertion is controlled by fiels +# bit11-10: 2, M_DQ, M_DM, and M_DQS I/O buffer ODT 75 ohm +# bit13-12: 2, M_STARTBURST_IN I/O buffer ODT 75 ohm +# bit14: 1, M_STARTBURST_IN ODT enabled +# bit15: 1, DDR IO ODT Unit: Drive ODT calibration values +# bit20-16: 0, Pad N channel driving strength for ODT +# bit25-21: 0, Pad P channel driving strength for ODT +# bit31-26: 0 required + +# DDR Initialization Control +DATA 0xFFD01480 0x00000001 +# bit0: 1, enable DDR init upon this register write +# bit31-1: 0, required + +# End of Header extension +DATA 0x0 0x0 diff --git a/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.c b/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.c new file mode 100644 index 000000000..659a124b2 --- /dev/null +++ b/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.c @@ -0,0 +1,290 @@ +/* + * Copyright (c) 2012 Michael Walle + * Michael Walle + * + * Based on sheevaplug/sheevaplug.c by + * Marvell Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "lsxl.h" + +/* + * Rescue mode + * + * Selected by holding the push button for 3 seconds, while powering on + * the device. + * + * These linkstations don't have a (populated) serial port. There is no + * way to access an (unmodified) board other than using the netconsole. If + * you want to recover from a bad environment setting or an empty environment, + * you can do this only with a working network connection. Therefore, a random + * ethernet address is generated if none is set and a DHCP request is sent. + * After a successful DHCP response is received, the network settings are + * configured and the ncip is unset. Therefore, all netconsole packets are + * broadcasted. + * Additionally, the bootsource is set to 'rescue'. + */ + +#ifndef CONFIG_ENV_OVERWRITE +# error "You need to set CONFIG_ENV_OVERWRITE" +#endif + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + kw_config_gpio(LSXL_OE_VAL_LOW, + LSXL_OE_VAL_HIGH, + LSXL_OE_LOW, LSXL_OE_HIGH); + + /* + * Multi-Purpose Pins Functionality configuration + * These strappings are taken from the original vendor uboot port. + */ + static const u32 kwmpp_config[] = { + MPP0_SPI_SCn, + MPP1_SPI_MOSI, + MPP2_SPI_SCK, + MPP3_SPI_MISO, + MPP4_UART0_RXD, + MPP5_UART0_TXD, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_GPIO, + MPP9_GPIO, + MPP10_GPO, /* HDD power */ + MPP11_GPIO, /* USB Vbus enable */ + MPP12_SD_CLK, + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_GPO, /* fan speed high */ + MPP19_GPO, /* fan speed low */ + MPP20_GE1_0, + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, + MPP29_GPIO, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GPIO, + MPP35_GPIO, + MPP36_GPIO, /* function LED */ + MPP37_GPIO, /* alarm LED */ + MPP38_GPIO, /* info LED */ + MPP39_GPIO, /* power LED */ + MPP40_GPIO, /* fan alarm */ + MPP41_GPIO, /* funtion button */ + MPP42_GPIO, /* power switch */ + MPP43_GPIO, /* power auto switch */ + MPP44_GPIO, + MPP45_GPIO, + MPP46_GPIO, + MPP47_GPIO, + MPP48_GPIO, /* function red LED */ + MPP49_GPIO, + 0 + }; + + kirkwood_mpp_conf(kwmpp_config, NULL); + + return 0; +} + +#define LED_OFF 0 +#define LED_ALARM_ON 1 +#define LED_ALARM_BLINKING 2 +#define LED_POWER_ON 3 +#define LED_POWER_BLINKING 4 +#define LED_INFO_ON 5 +#define LED_INFO_BLINKING 6 + +static void __set_led(int blink_alarm, int blink_info, int blink_power, + int value_alarm, int value_info, int value_power) +{ + kw_gpio_set_blink(GPIO_ALARM_LED, blink_alarm); + kw_gpio_set_blink(GPIO_INFO_LED, blink_info); + kw_gpio_set_blink(GPIO_POWER_LED, blink_power); + kw_gpio_set_value(GPIO_ALARM_LED, value_alarm); + kw_gpio_set_value(GPIO_INFO_LED, value_info); + kw_gpio_set_value(GPIO_POWER_LED, value_power); +} + +static void set_led(int state) +{ + switch (state) { + case LED_OFF: + __set_led(0, 0, 0, 1, 1, 1); + break; + case LED_ALARM_ON: + __set_led(0, 0, 0, 0, 1, 1); + break; + case LED_ALARM_BLINKING: + __set_led(1, 0, 0, 1, 1, 1); + break; + case LED_INFO_ON: + __set_led(0, 0, 0, 1, 0, 1); + break; + case LED_INFO_BLINKING: + __set_led(0, 1, 0, 1, 1, 1); + break; + case LED_POWER_ON: + __set_led(0, 0, 0, 1, 1, 0); + break; + case LED_POWER_BLINKING: + __set_led(0, 0, 1, 1, 1, 1); + break; + } +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + + set_led(LED_POWER_BLINKING); + + return 0; +} + +#ifdef CONFIG_MISC_INIT_R +static void check_power_switch(void) +{ + if (kw_gpio_get_value(GPIO_POWER_SWITCH)) { + /* turn off fan, HDD and USB power */ + kw_gpio_set_value(GPIO_HDD_POWER, 0); + kw_gpio_set_value(GPIO_USB_VBUS, 0); + kw_gpio_set_value(GPIO_FAN_HIGH, 1); + kw_gpio_set_value(GPIO_FAN_LOW, 1); + set_led(LED_OFF); + + /* loop until released */ + while (kw_gpio_get_value(GPIO_POWER_SWITCH)) + ; + + /* turn power on again */ + kw_gpio_set_value(GPIO_HDD_POWER, 1); + kw_gpio_set_value(GPIO_USB_VBUS, 1); + kw_gpio_set_value(GPIO_FAN_HIGH, 0); + kw_gpio_set_value(GPIO_FAN_LOW, 0); + set_led(LED_POWER_BLINKING); + } +} + +void check_enetaddr(void) +{ + uchar enetaddr[6]; + + if (!eth_getenv_enetaddr("ethaddr", enetaddr)) { + /* signal unset/invalid ethaddr to user */ + set_led(LED_INFO_BLINKING); + } +} + +static void erase_environment(void) +{ + struct spi_flash *flash; + + printf("Erasing environment..\n"); + flash = spi_flash_probe(0, 0, 1000000, SPI_MODE_3); + if (!flash) { + printf("Erasing flash failed\n"); + return; + } + + spi_flash_erase(flash, CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE); + spi_flash_free(flash); + do_reset(NULL, 0, 0, NULL); +} + +static void rescue_mode(void) +{ + uchar enetaddr[6]; + + printf("Entering rescue mode..\n"); +#ifdef CONFIG_RANDOM_MACADDR + if (!eth_getenv_enetaddr("ethaddr", enetaddr)) { + eth_random_addr(enetaddr); + if (eth_setenv_enetaddr("ethaddr", enetaddr)) { + printf("Failed to set ethernet address\n"); + set_led(LED_ALARM_BLINKING); + return; + } + } +#endif + setenv("bootsource", "rescue"); +} + +static void check_push_button(void) +{ + int i = 0; + + while (!kw_gpio_get_value(GPIO_FUNC_BUTTON)) { + udelay(100000); + i++; + + if (i == 10) + set_led(LED_INFO_ON); + + if (i >= 100) { + set_led(LED_INFO_BLINKING); + break; + } + } + + if (i >= 100) + erase_environment(); + else if (i >= 10) + rescue_mode(); +} + +int misc_init_r(void) +{ + check_power_switch(); + check_enetaddr(); + check_push_button(); + + return 0; +} +#endif + +#ifdef CONFIG_SHOW_BOOT_PROGRESS +void show_boot_progress(int progress) +{ + if (progress > 0) + return; + + /* this is not an error, eg. bootp with autoload=no will trigger this */ + if (progress == -BOOTSTAGE_ID_NET_LOADED) + return; + + set_led(LED_ALARM_BLINKING); +} +#endif diff --git a/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.h b/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.h new file mode 100644 index 000000000..d5e79ac62 --- /dev/null +++ b/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.h @@ -0,0 +1,59 @@ +/* + * Copyright (c) 2012 Michael Walle + * Michael Walle + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __LSXL_H +#define __LSXL_H + +#define GPIO_HDD_POWER 10 +#define GPIO_USB_VBUS 11 +#define GPIO_FAN_HIGH 18 +#define GPIO_FAN_LOW 19 +#define GPIO_FUNC_LED 36 +#define GPIO_ALARM_LED 37 +#define GPIO_INFO_LED 38 +#define GPIO_POWER_LED 39 +#define GPIO_FAN_LOCK 40 +#define GPIO_FUNC_BUTTON 41 +#define GPIO_POWER_SWITCH 42 +#define GPIO_POWER_AUTO_SWITCH 43 +#define GPIO_FUNC_RED_LED 48 + +#define _BIT(x) (1<<(x)) + +#define LSXL_OE_LOW (~(_BIT(GPIO_HDD_POWER) \ + | _BIT(GPIO_USB_VBUS) \ + | _BIT(GPIO_FAN_HIGH) \ + | _BIT(GPIO_FAN_LOW))) + +#define LSXL_OE_HIGH (~(_BIT(GPIO_FUNC_LED - 32) \ + | _BIT(GPIO_ALARM_LED - 32) \ + | _BIT(GPIO_INFO_LED - 32) \ + | _BIT(GPIO_POWER_LED - 32) \ + | _BIT(GPIO_FUNC_RED_LED - 32))) + +#define LSXL_OE_VAL_LOW (_BIT(GPIO_HDD_POWER) \ + | _BIT(GPIO_USB_VBUS)) + +#define LSXL_OE_VAL_HIGH (_BIT(GPIO_FUNC_LED - 32) \ + | _BIT(GPIO_ALARM_LED - 32) \ + | _BIT(GPIO_INFO_LED - 32) \ + | _BIT(GPIO_POWER_LED - 32) \ + | _BIT(GPIO_FUNC_RED_LED - 32)) + +#define LSXL_POL_VAL_LOW (_BIT(GPIO_FAN_HIGH) \ + | _BIT(GPIO_FAN_LOW)) + +#define LSXL_POL_VAL_HIGH (_BIT(GPIO_FUNC_LED - 32) \ + | _BIT(GPIO_ALARM_LED - 32) \ + | _BIT(GPIO_INFO_LED - 32) \ + | _BIT(GPIO_POWER_LED - 32) \ + | _BIT(GPIO_FUNC_BUTTON - 32) \ + | _BIT(GPIO_POWER_SWITCH - 32) \ + | _BIT(GPIO_POWER_AUTO_SWITCH - 32) \ + | _BIT(GPIO_FUNC_RED_LED - 32)) + +#endif /* __LSXL_H */ -- cgit 1.2.3-korg