From e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb Mon Sep 17 00:00:00 2001 From: Yang Zhang Date: Fri, 28 Aug 2015 09:58:54 +0800 Subject: Add qemu 2.4.0 Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang --- qemu/roms/u-boot/board/amcc/makalu/Makefile | 9 + qemu/roms/u-boot/board/amcc/makalu/cmd_pll.c | 279 +++++++++++++++++++++++++++ qemu/roms/u-boot/board/amcc/makalu/init.S | 15 ++ qemu/roms/u-boot/board/amcc/makalu/makalu.c | 223 +++++++++++++++++++++ 4 files changed, 526 insertions(+) create mode 100644 qemu/roms/u-boot/board/amcc/makalu/Makefile create mode 100644 qemu/roms/u-boot/board/amcc/makalu/cmd_pll.c create mode 100644 qemu/roms/u-boot/board/amcc/makalu/init.S create mode 100644 qemu/roms/u-boot/board/amcc/makalu/makalu.c (limited to 'qemu/roms/u-boot/board/amcc/makalu') diff --git a/qemu/roms/u-boot/board/amcc/makalu/Makefile b/qemu/roms/u-boot/board/amcc/makalu/Makefile new file mode 100644 index 000000000..dcf162ca9 --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/makalu/Makefile @@ -0,0 +1,9 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y = makalu.o cmd_pll.o +obj-y += init.o diff --git a/qemu/roms/u-boot/board/amcc/makalu/cmd_pll.c b/qemu/roms/u-boot/board/amcc/makalu/cmd_pll.c new file mode 100644 index 000000000..f12655bea --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/makalu/cmd_pll.c @@ -0,0 +1,279 @@ +/* + * (C) Copyright 2000, 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * ehnus: change pll frequency. + * Wed Sep 5 11:45:17 CST 2007 + * hsun@udtech.com.cn + */ + + +#include +#include +#include +#include + +#ifdef CONFIG_CMD_EEPROM + +#define EEPROM_CONF_OFFSET 0 +#define EEPROM_TEST_OFFSET 16 +#define EEPROM_SDSTP_PARAM 16 + +#define PLL_NAME_MAX 12 +#define BUF_STEP 8 + +/* eeprom_wirtes 8Byte per op. */ +#define EEPROM_ALTER_FREQ(freq) \ + do { \ + int __i; \ + for (__i = 0; __i < 2; __i++) \ + eeprom_write (CONFIG_SYS_I2C_EEPROM_ADDR, \ + EEPROM_CONF_OFFSET + __i*BUF_STEP, \ + pll_select[freq], \ + BUF_STEP + __i*BUF_STEP); \ + } while (0) + +#define PDEBUG +#ifdef PDEBUG +#define PLL_DEBUG pll_debug(EEPROM_CONF_OFFSET) +#else +#define PLL_DEBUG +#endif + +typedef enum { + PLL_ebc20, + PLL_333, + PLL_4001, + PLL_4002, + PLL_533, + PLL_600, + PLL_666, /* For now, kilauea can't support */ + RCONF, + WTEST, + PLL_TOTAL +} pll_freq_t; + +static const char +pll_name[][PLL_NAME_MAX] = { + "PLL_ebc20", + "PLL_333", + "PLL_400@1", + "PLL_400@2", + "PLL_533", + "PLL_600", + "PLL_666", + "RCONF", + "WTEST", + "" +}; + +/* + * ehnus: + */ +static uchar +pll_select[][EEPROM_SDSTP_PARAM] = { + /* 0: CPU 333MHz EBC 20MHz, for test only */ + { + 0x8c, 0x12, 0xec, 0x12, 0x88, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 0: 333 */ + { + 0x8c, 0x12, 0xec, 0x12, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 1: 400_266 */ + { + 0x8e, 0x0e, 0xe8, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 2: 400 */ + { + 0x8e, 0x0e, 0xe8, 0x12, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 3: 533 */ + { + 0x8e, 0x43, 0x60, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 4: 600 */ + { + 0x8d, 0x02, 0x34, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 5: 666 */ + { + 0x8d, 0x03, 0x78, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + {} +}; + +static uchar +testbuf[EEPROM_SDSTP_PARAM] = { + 0x00, 0x11, 0x22, 0x33, 0x44, 0x55, 0x66, 0x77, + 0x88, 0x99, 0xaa, 0xbb, 0xcc, 0xdd, 0xee, 0xff +}; + +static void +pll_debug(int off) +{ + int i; + uchar buffer[EEPROM_SDSTP_PARAM]; + + memset(buffer, 0, sizeof(buffer)); + eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, off, + buffer, EEPROM_SDSTP_PARAM); + + printf("Debug: SDSTP[0-3] at offset \"0x%02x\" lists as follows: \n", off); + for (i = 0; i < EEPROM_SDSTP_PARAM; i++) + printf("%02x ", buffer[i]); + printf("\n"); +} + +static void +test_write(void) +{ + printf("Debug: test eeprom_write ... "); + + /* + * Write twice, 8 bytes per write + */ + eeprom_write (CONFIG_SYS_I2C_EEPROM_ADDR, EEPROM_TEST_OFFSET, + testbuf, 8); + eeprom_write (CONFIG_SYS_I2C_EEPROM_ADDR, EEPROM_TEST_OFFSET+8, + testbuf, 16); + printf("done\n"); + + pll_debug(EEPROM_TEST_OFFSET); +} + +int +do_pll_alter (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + char c = '\0'; + pll_freq_t pll_freq; + + if (argc < 2) + return cmd_usage(cmdtp); + + for (pll_freq = PLL_ebc20; pll_freq < PLL_TOTAL; pll_freq++) { + if (!strcmp(pll_name[pll_freq], argv[1])) + break; + } + + switch (pll_freq) { + case PLL_ebc20: + case PLL_333: + case PLL_4001: + case PLL_4002: + case PLL_533: + case PLL_600: + EEPROM_ALTER_FREQ(pll_freq); + break; + + case PLL_666: /* not support */ + printf("Choose this option will result in a boot failure." + "\nContinue? (Y/N): "); + + c = getc(); putc('\n'); + + if ((c == 'y') || (c == 'Y')) { + EEPROM_ALTER_FREQ(pll_freq); + break; + } + goto ret; + + case RCONF: + pll_debug(EEPROM_CONF_OFFSET); + goto ret; + case WTEST: + printf("DEBUG: write test\n"); + test_write(); + goto ret; + + default: + printf("Invalid options\n\n"); + return cmd_usage(cmdtp); + } + + printf("PLL set to %s, " + "reset the board to take effect\n", pll_name[pll_freq]); + + PLL_DEBUG; +ret: + return 0; +} + +U_BOOT_CMD( + pllalter, CONFIG_SYS_MAXARGS, 1, do_pll_alter, + "change pll frequence", + "pllalter - change pll frequence \n\n\ + ** New freq take effect after reset. ** \n\ + ----------------------------------------------\n\ + PLL_ebc20: Board: AMCC 405EX(r) Evaluation Board\n\ + \t Same as PLL_333 \n\ + \t except \n\ + \t EBC: 20 MHz \n\ + ----------------------------------------------\n\ + PLL_333: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 666 MHz \n\ + \t CPU: 333 MHz \n\ + \t PLB: 166 MHz \n\ + \t OPB: 83 MHz \n\ + \t DDR: 83 MHz \n\ + ------------------------------------------------\n\ + PLL_400@1: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 800 MHz \n\ + \t CPU: 400 MHz \n\ + \t PLB: 133 MHz \n\ + \t OPB: 66 MHz \n\ + \t DDR: 133 MHz \n\ + ------------------------------------------------\n\ + PLL_400@2: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 800 MHz \n\ + \t CPU: 400 MHz \n\ + \t PLB: 200 MHz \n\ + \t OPB: 100 MHz \n\ + \t DDR: 200 MHz \n\ + ----------------------------------------------\n\ + PLL_533: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1066 MHz \n\ + \t CPU: 533 MHz \n\ + \t PLB: 177 MHz \n\ + \t OPB: 88 MHz \n\ + \t DDR: 177 MHz \n\ + ----------------------------------------------\n\ + PLL_600: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1200 MHz \n\ + \t CPU: 600 MHz \n\ + \t PLB: 200 MHz \n\ + \t OPB: 100 MHz \n\ + \t DDR: 200 MHz \n\ + ----------------------------------------------\n\ + PLL_666: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1333 MHz \n\ + \t CPU: 666 MHz \n\ + \t PLB: 166 MHz \n\ + \t OPB: 83 MHz \n\ + \t DDR: 166 MHz \n\ + -----------------------------------------------\n\ + RCONF: Read current eeprom configuration. \n\ + -----------------------------------------------\n\ + WTEST: Test EEPROM write with predefined values\n\ + -----------------------------------------------" +); + +#endif /* CONFIG_CMD_EEPROM */ diff --git a/qemu/roms/u-boot/board/amcc/makalu/init.S b/qemu/roms/u-boot/board/amcc/makalu/init.S new file mode 100644 index 000000000..e15c62249 --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/makalu/init.S @@ -0,0 +1,15 @@ +/* + * Copyright (c) 2008 Nuovation System Designs, LLC + * Grant Erickson + * + * (C) Copyright 2007-2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Originally based on code provided from Senao and AMCC + * + * SPDX-License-Identifier: GPL-2.0+ + */ + + .globl ext_bus_cntlr_init +ext_bus_cntlr_init: + blr diff --git a/qemu/roms/u-boot/board/amcc/makalu/makalu.c b/qemu/roms/u-boot/board/amcc/makalu/makalu.c new file mode 100644 index 000000000..a6ad2a1ba --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/makalu/makalu.c @@ -0,0 +1,223 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#if defined(CONFIG_PCI) +#include +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; + +extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +/* + * Board early initialization function + */ +int board_early_init_f (void) +{ + u32 val; + + /*--------------------------------------------------------------------+ + | Interrupt controller setup for the AMCC 405EX(r) PINE evaluation board. + +--------------------------------------------------------------------+ + +---------------------------------------------------------------------+ + |Interrupt| Source | Pol. | Sensi.| Crit. | + +---------+-----------------------------------+-------+-------+-------+ + | IRQ 00 | UART0 | High | Level | Non | + | IRQ 01 | UART1 | High | Level | Non | + | IRQ 02 | IIC0 | High | Level | Non | + | IRQ 03 | TBD | High | Level | Non | + | IRQ 04 | TBD | High | Level | Non | + | IRQ 05 | EBM | High | Level | Non | + | IRQ 06 | BGI | High | Level | Non | + | IRQ 07 | IIC1 | Rising| Edge | Non | + | IRQ 08 | SPI | High | Lvl/ed| Non | + | IRQ 09 | External IRQ 0 - (PCI-Express) | pgm H | Pgm | Non | + | IRQ 10 | MAL TX EOB | High | Level | Non | + | IRQ 11 | MAL RX EOB | High | Level | Non | + | IRQ 12 | DMA Channel 0 FIFO Full | High | Level | Non | + | IRQ 13 | DMA Channel 0 Stat FIFO | High | Level | Non | + | IRQ 14 | DMA Channel 1 FIFO Full | High | Level | Non | + | IRQ 15 | DMA Channel 1 Stat FIFO | High | Level | Non | + | IRQ 16 | PCIE0 AL | high | Level | Non | + | IRQ 17 | PCIE0 VPD access | rising| Edge | Non | + | IRQ 18 | PCIE0 hot reset request | rising| Edge | Non | + | IRQ 19 | PCIE0 hot reset request | faling| Edge | Non | + | IRQ 20 | PCIE0 TCR | High | Level | Non | + | IRQ 21 | PCIE0 MSI level0 | High | Level | Non | + | IRQ 22 | PCIE0 MSI level1 | High | Level | Non | + | IRQ 23 | Security EIP-94 | High | Level | Non | + | IRQ 24 | EMAC0 interrupt | High | Level | Non | + | IRQ 25 | EMAC1 interrupt | High | Level | Non | + | IRQ 26 | PCIE0 MSI level2 | High | Level | Non | + | IRQ 27 | External IRQ 4 | pgm H | Pgm | Non | + | IRQ 28 | UIC2 Non-critical Int. | High | Level | Non | + | IRQ 29 | UIC2 Critical Interrupt | High | Level | Crit. | + | IRQ 30 | UIC1 Non-critical Int. | High | Level | Non | + | IRQ 31 | UIC1 Critical Interrupt | High | Level | Crit. | + |---------------------------------------------------------------------- + | IRQ 32 | MAL Serr | High | Level | Non | + | IRQ 33 | MAL Txde | High | Level | Non | + | IRQ 34 | MAL Rxde | High | Level | Non | + | IRQ 35 | PCIE0 bus master VC0 |falling| Edge | Non | + | IRQ 36 | PCIE0 DCR Error | High | Level | Non | + | IRQ 37 | EBC | High |Lvl Edg| Non | + | IRQ 38 | NDFC | High | Level | Non | + | IRQ 39 | GPT Compare Timer 8 | Risin | Edge | Non | + | IRQ 40 | GPT Compare Timer 9 | Risin | Edge | Non | + | IRQ 41 | PCIE1 AL | high | Level | Non | + | IRQ 42 | PCIE1 VPD access | rising| edge | Non | + | IRQ 43 | PCIE1 hot reset request | rising| Edge | Non | + | IRQ 44 | PCIE1 hot reset request | faling| Edge | Non | + | IRQ 45 | PCIE1 TCR | High | Level | Non | + | IRQ 46 | PCIE1 bus master VC0 |falling| Edge | Non | + | IRQ 47 | GPT Compare Timer 3 | Risin | Edge | Non | + | IRQ 48 | GPT Compare Timer 4 | Risin | Edge | Non | + | IRQ 49 | Ext. IRQ 7 |pgm/Fal|pgm/Lvl| Non | + | IRQ 50 | Ext. IRQ 8 - |pgm (H)|pgm/Lvl| Non | + | IRQ 51 | Ext. IRQ 9 |pgm (H)|pgm/Lvl| Non | + | IRQ 52 | GPT Compare Timer 5 | high | Edge | Non | + | IRQ 53 | GPT Compare Timer 6 | high | Edge | Non | + | IRQ 54 | GPT Compare Timer 7 | high | Edge | Non | + | IRQ 55 | Serial ROM | High | Level | Non | + | IRQ 56 | GPT Decrement Pulse | High | Level | Non | + | IRQ 57 | Ext. IRQ 2 |pgm/Fal|pgm/Lvl| Non | + | IRQ 58 | Ext. IRQ 5 |pgm/Fal|pgm/Lvl| Non | + | IRQ 59 | Ext. IRQ 6 |pgm/Fal|pgm/Lvl| Non | + | IRQ 60 | EMAC0 Wake-up | High | Level | Non | + | IRQ 61 | Ext. IRQ 1 |pgm/Fal|pgm/Lvl| Non | + | IRQ 62 | EMAC1 Wake-up | High | Level | Non | + |---------------------------------------------------------------------- + | IRQ 64 | PE0 AL | High | Level | Non | + | IRQ 65 | PE0 VPD Access | Risin | Edge | Non | + | IRQ 66 | PE0 Hot Reset Request | Risin | Edge | Non | + | IRQ 67 | PE0 Hot Reset Request | Falli | Edge | Non | + | IRQ 68 | PE0 TCR | High | Level | Non | + | IRQ 69 | PE0 BusMaster VCO | Falli | Edge | Non | + | IRQ 70 | PE0 DCR Error | High | Level | Non | + | IRQ 71 | Reserved | N/A | N/A | Non | + | IRQ 72 | PE1 AL | High | Level | Non | + | IRQ 73 | PE1 VPD Access | Risin | Edge | Non | + | IRQ 74 | PE1 Hot Reset Request | Risin | Edge | Non | + | IRQ 75 | PE1 Hot Reset Request | Falli | Edge | Non | + | IRQ 76 | PE1 TCR | High | Level | Non | + | IRQ 77 | PE1 BusMaster VCO | Falli | Edge | Non | + | IRQ 78 | PE1 DCR Error | High | Level | Non | + | IRQ 79 | Reserved | N/A | N/A | Non | + | IRQ 80 | PE2 AL | High | Level | Non | + | IRQ 81 | PE2 VPD Access | Risin | Edge | Non | + | IRQ 82 | PE2 Hot Reset Request | Risin | Edge | Non | + | IRQ 83 | PE2 Hot Reset Request | Falli | Edge | Non | + | IRQ 84 | PE2 TCR | High | Level | Non | + | IRQ 85 | PE2 BusMaster VCO | Falli | Edge | Non | + | IRQ 86 | PE2 DCR Error | High | Level | Non | + | IRQ 87 | Reserved | N/A | N/A | Non | + | IRQ 88 | External IRQ(5) | Progr | Progr | Non | + | IRQ 89 | External IRQ 4 - Ethernet | Progr | Progr | Non | + | IRQ 90 | External IRQ 3 - PCI-X | Progr | Progr | Non | + | IRQ 91 | External IRQ 2 - PCI-X | Progr | Progr | Non | + | IRQ 92 | External IRQ 1 - PCI-X | Progr | Progr | Non | + | IRQ 93 | External IRQ 0 - PCI-X | Progr | Progr | Non | + | IRQ 94 | Reserved | N/A | N/A | Non | + | IRQ 95 | Reserved | N/A | N/A | Non | + |--------------------------------------------------------------------- + +---------+-----------------------------------+-------+-------+------*/ + /*--------------------------------------------------------------------+ + | Initialise UIC registers. Clear all interrupts. Disable all + | interrupts. + | Set critical interrupt values. Set interrupt polarities. Set + | interrupt trigger levels. Make bit 0 High priority. Clear all + | interrupts again. + +-------------------------------------------------------------------*/ + + mtdcr (UIC2SR, 0xffffffff); /* Clear all interrupts */ + mtdcr (UIC2ER, 0x00000000); /* disable all interrupts */ + mtdcr (UIC2CR, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (UIC2PR, 0xf7ffffff); /* Set Interrupt Polarities */ + mtdcr (UIC2TR, 0x01e1fff8); /* Set Interrupt Trigger Levels */ + mtdcr (UIC2VR, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (UIC2SR, 0x00000000); /* clear all interrupts */ + mtdcr (UIC2SR, 0xffffffff); /* clear all interrupts */ + + mtdcr (UIC1SR, 0xffffffff); /* Clear all interrupts */ + mtdcr (UIC1ER, 0x00000000); /* disable all interrupts */ + mtdcr (UIC1CR, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (UIC1PR, 0xfffac785); /* Set Interrupt Polarities */ + mtdcr (UIC1TR, 0x001d0040); /* Set Interrupt Trigger Levels */ + mtdcr (UIC1VR, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (UIC1SR, 0x00000000); /* clear all interrupts */ + mtdcr (UIC1SR, 0xffffffff); /* clear all interrupts */ + + mtdcr (UIC0SR, 0xffffffff); /* Clear all interrupts */ + mtdcr (UIC0ER, 0x0000000a); /* Disable all interrupts */ + /* Except cascade UIC0 and UIC1 */ + mtdcr (UIC0CR, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (UIC0PR, 0xffbfefef); /* Set Interrupt Polarities */ + mtdcr (UIC0TR, 0x00007000); /* Set Interrupt Trigger Levels */ + mtdcr (UIC0VR, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (UIC0SR, 0x00000000); /* clear all interrupts */ + mtdcr (UIC0SR, 0xffffffff); /* clear all interrupts */ + + /* + * Note: Some cores are still in reset when the chip starts, so + * take them out of reset + */ + mtsdr(SDR0_SRST, 0); + + /* Reset PCIe slots */ + gpio_write_bit(CONFIG_SYS_GPIO_PCIE_RST, 0); + udelay(100); + gpio_write_bit(CONFIG_SYS_GPIO_PCIE_RST, 1); + + /* + * Configure PFC (Pin Function Control) registers + * -> Enable USB + */ + val = SDR0_PFC1_USBEN | SDR0_PFC1_USBBIGEN | SDR0_PFC1_GPT_FREQ; + mtsdr(SDR0_PFC1, val); + + return 0; +} + +int misc_init_r(void) +{ +#ifdef CONFIG_ENV_IS_IN_FLASH + /* Monitor protection ON by default */ + flash_protect(FLAG_PROTECT_SET, + -CONFIG_SYS_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); +#endif + + return 0; +} + +int checkboard (void) +{ + char buf[64]; + int i = getenv_f("serial#", buf, sizeof(buf)); + + printf("Board: Makalu - AMCC PPC405EX Evaluation Board"); + + if (i > 0) { + puts(", serial# "); + puts(buf); + } + putc('\n'); + + return (0); +} -- cgit 1.2.3-korg