From e09b41010ba33a20a87472ee821fa407a5b8da36 Mon Sep 17 00:00:00 2001 From: José Pekkarinen Date: Mon, 11 Apr 2016 10:41:07 +0300 Subject: These changes are the raw update to linux-4.4.6-rt14. Kernel sources are taken from kernel.org, and rt patch from the rt wiki download page. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit During the rebasing, the following patch collided: Force tick interrupt and get rid of softirq magic(I70131fb85). Collisions have been removed because its logic was found on the source already. Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769 Signed-off-by: José Pekkarinen --- kernel/drivers/gpu/drm/i915/dvo_ns2501.c | 674 +++++++++++++++++-------------- 1 file changed, 376 insertions(+), 298 deletions(-) (limited to 'kernel/drivers/gpu/drm/i915/dvo_ns2501.c') diff --git a/kernel/drivers/gpu/drm/i915/dvo_ns2501.c b/kernel/drivers/gpu/drm/i915/dvo_ns2501.c index 441630434..063859fff 100644 --- a/kernel/drivers/gpu/drm/i915/dvo_ns2501.c +++ b/kernel/drivers/gpu/drm/i915/dvo_ns2501.c @@ -60,6 +60,130 @@ #define NS2501_REGC 0x0c +/* + * The following registers are not part of the official datasheet + * and are the result of reverse engineering. + */ + +/* + * Register c0 controls how the DVO synchronizes with + * its input. + */ +#define NS2501_REGC0 0xc0 +#define NS2501_C0_ENABLE (1<<0) /* enable the DVO sync in general */ +#define NS2501_C0_HSYNC (1<<1) /* synchronize horizontal with input */ +#define NS2501_C0_VSYNC (1<<2) /* synchronize vertical with input */ +#define NS2501_C0_RESET (1<<7) /* reset the synchronization flip/flops */ + +/* + * Register 41 is somehow related to the sync register and sync + * configuration. It should be 0x32 whenever regC0 is 0x05 (hsync off) + * and 0x00 otherwise. + */ +#define NS2501_REG41 0x41 + +/* + * this register controls the dithering of the DVO + * One bit enables it, the other define the dithering depth. + * The higher the value, the lower the dithering depth. + */ +#define NS2501_F9_REG 0xf9 +#define NS2501_F9_ENABLE (1<<0) /* if set, dithering is enabled */ +#define NS2501_F9_DITHER_MASK (0x7f<<1) /* controls the dither depth */ +#define NS2501_F9_DITHER_SHIFT 1 /* shifts the dither mask */ + +/* + * PLL configuration register. This is a pair of registers, + * one single byte register at 1B, and a pair at 1C,1D. + * These registers are counters/dividers. + */ +#define NS2501_REG1B 0x1b /* one byte PLL control register */ +#define NS2501_REG1C 0x1c /* low-part of the second register */ +#define NS2501_REG1D 0x1d /* high-part of the second register */ + +/* + * Scaler control registers. Horizontal at b8,b9, + * vertical at 10,11. The scale factor is computed as + * 2^16/control-value. The low-byte comes first. + */ +#define NS2501_REG10 0x10 /* low-byte vertical scaler */ +#define NS2501_REG11 0x11 /* high-byte vertical scaler */ +#define NS2501_REGB8 0xb8 /* low-byte horizontal scaler */ +#define NS2501_REGB9 0xb9 /* high-byte horizontal scaler */ + +/* + * Display window definition. This consists of four registers + * per dimension. One register pair defines the start of the + * display, one the end. + * As far as I understand, this defines the window within which + * the scaler samples the input. + */ +#define NS2501_REGC1 0xc1 /* low-byte horizontal display start */ +#define NS2501_REGC2 0xc2 /* high-byte horizontal display start */ +#define NS2501_REGC3 0xc3 /* low-byte horizontal display stop */ +#define NS2501_REGC4 0xc4 /* high-byte horizontal display stop */ +#define NS2501_REGC5 0xc5 /* low-byte vertical display start */ +#define NS2501_REGC6 0xc6 /* high-byte vertical display start */ +#define NS2501_REGC7 0xc7 /* low-byte vertical display stop */ +#define NS2501_REGC8 0xc8 /* high-byte vertical display stop */ + +/* + * The following register pair seems to define the start of + * the vertical sync. If automatic syncing is enabled, and the + * register value defines a sync pulse that is later than the + * incoming sync, then the register value is ignored and the + * external hsync triggers the synchronization. + */ +#define NS2501_REG80 0x80 /* low-byte vsync-start */ +#define NS2501_REG81 0x81 /* high-byte vsync-start */ + +/* + * The following register pair seems to define the total number + * of lines created at the output side of the scaler. + * This is again a low-high register pair. + */ +#define NS2501_REG82 0x82 /* output display height, low byte */ +#define NS2501_REG83 0x83 /* output display height, high byte */ + +/* + * The following registers define the end of the front-porch + * in horizontal and vertical position and hence allow to shift + * the image left/right or up/down. + */ +#define NS2501_REG98 0x98 /* horizontal start of display + 256, low */ +#define NS2501_REG99 0x99 /* horizontal start of display + 256, high */ +#define NS2501_REG8E 0x8e /* vertical start of the display, low byte */ +#define NS2501_REG8F 0x8f /* vertical start of the display, high byte */ + +/* + * The following register pair control the function of the + * backlight and the DVO output. To enable the corresponding + * function, the corresponding bit must be set in both registers. + */ +#define NS2501_REG34 0x34 /* DVO enable functions, first register */ +#define NS2501_REG35 0x35 /* DVO enable functions, second register */ +#define NS2501_34_ENABLE_OUTPUT (1<<0) /* enable DVO output */ +#define NS2501_34_ENABLE_BACKLIGHT (1<<1) /* enable backlight */ + +/* + * Registers 9C and 9D define the vertical output offset + * of the visible region. + */ +#define NS2501_REG9C 0x9c +#define NS2501_REG9D 0x9d + +/* + * The register 9F defines the dithering. This requires the + * scaler to be ON. Bit 0 enables dithering, the remaining + * bits control the depth of the dither. The higher the value, + * the LOWER the dithering amplitude. A good value seems to be + * 15 (total register value). + */ +#define NS2501_REGF9 0xf9 +#define NS2501_F9_ENABLE_DITHER (1<<0) /* enable dithering */ +#define NS2501_F9_DITHER_MASK (0x7f<<1) /* dither masking */ +#define NS2501_F9_DITHER_SHIFT 1 /* upshift of the dither mask */ + enum { MODE_640x480, MODE_800x600, @@ -72,274 +196,178 @@ struct ns2501_reg { }; /* - * Magic values based on what the BIOS on - * Fujitsu-Siemens Lifebook S6010 programs (1024x768 panel). + * The following structure keeps the complete configuration of + * the DVO, given a specific output configuration. + * This is pretty much guess-work from reverse-engineering, so + * read all this with a grain of salt. + */ +struct ns2501_configuration { + uint8_t sync; /* configuration of the C0 register */ + uint8_t conf; /* configuration register 8 */ + uint8_t syncb; /* configuration register 41 */ + uint8_t dither; /* configuration of the dithering */ + uint8_t pll_a; /* PLL configuration, register A, 1B */ + uint16_t pll_b; /* PLL configuration, register B, 1C/1D */ + uint16_t hstart; /* horizontal start, registers C1/C2 */ + uint16_t hstop; /* horizontal total, registers C3/C4 */ + uint16_t vstart; /* vertical start, registers C5/C6 */ + uint16_t vstop; /* vertical total, registers C7/C8 */ + uint16_t vsync; /* manual vertical sync start, 80/81 */ + uint16_t vtotal; /* number of lines generated, 82/83 */ + uint16_t hpos; /* horizontal position + 256, 98/99 */ + uint16_t vpos; /* vertical position, 8e/8f */ + uint16_t voffs; /* vertical output offset, 9c/9d */ + uint16_t hscale; /* horizontal scaling factor, b8/b9 */ + uint16_t vscale; /* vertical scaling factor, 10/11 */ +}; + +/* + * DVO configuration values, partially based on what the BIOS + * of the Fujitsu Lifebook S6010 writes into registers, + * partially found by manual tweaking. These configurations assume + * a 1024x768 panel. */ -static const struct ns2501_reg regs_1024x768[][86] = { +static const struct ns2501_configuration ns2501_modes[] = { [MODE_640x480] = { - [0] = { .offset = 0x0a, .value = 0x81, }, - [1] = { .offset = 0x18, .value = 0x07, }, - [2] = { .offset = 0x19, .value = 0x00, }, - [3] = { .offset = 0x1a, .value = 0x00, }, - [4] = { .offset = 0x1b, .value = 0x11, }, - [5] = { .offset = 0x1c, .value = 0x54, }, - [6] = { .offset = 0x1d, .value = 0x03, }, - [7] = { .offset = 0x1e, .value = 0x02, }, - [8] = { .offset = 0xf3, .value = 0x90, }, - [9] = { .offset = 0xf9, .value = 0x00, }, - [10] = { .offset = 0xc1, .value = 0x90, }, - [11] = { .offset = 0xc2, .value = 0x00, }, - [12] = { .offset = 0xc3, .value = 0x0f, }, - [13] = { .offset = 0xc4, .value = 0x03, }, - [14] = { .offset = 0xc5, .value = 0x16, }, - [15] = { .offset = 0xc6, .value = 0x00, }, - [16] = { .offset = 0xc7, .value = 0x02, }, - [17] = { .offset = 0xc8, .value = 0x02, }, - [18] = { .offset = 0xf4, .value = 0x00, }, - [19] = { .offset = 0x80, .value = 0xff, }, - [20] = { .offset = 0x81, .value = 0x07, }, - [21] = { .offset = 0x82, .value = 0x3d, }, - [22] = { .offset = 0x83, .value = 0x05, }, - [23] = { .offset = 0x94, .value = 0x00, }, - [24] = { .offset = 0x95, .value = 0x00, }, - [25] = { .offset = 0x96, .value = 0x05, }, - [26] = { .offset = 0x97, .value = 0x00, }, - [27] = { .offset = 0x9a, .value = 0x88, }, - [28] = { .offset = 0x9b, .value = 0x00, }, - [29] = { .offset = 0x98, .value = 0x00, }, - [30] = { .offset = 0x99, .value = 0x00, }, - [31] = { .offset = 0xf7, .value = 0x88, }, - [32] = { .offset = 0xf8, .value = 0x0a, }, - [33] = { .offset = 0x9c, .value = 0x24, }, - [34] = { .offset = 0x9d, .value = 0x00, }, - [35] = { .offset = 0x9e, .value = 0x25, }, - [36] = { .offset = 0x9f, .value = 0x03, }, - [37] = { .offset = 0xa0, .value = 0x28, }, - [38] = { .offset = 0xa1, .value = 0x01, }, - [39] = { .offset = 0xa2, .value = 0x28, }, - [40] = { .offset = 0xa3, .value = 0x05, }, - [41] = { .offset = 0xb6, .value = 0x09, }, - [42] = { .offset = 0xb8, .value = 0x00, }, - [43] = { .offset = 0xb9, .value = 0xa0, }, - [44] = { .offset = 0xba, .value = 0x00, }, - [45] = { .offset = 0xbb, .value = 0x20, }, - [46] = { .offset = 0x10, .value = 0x00, }, - [47] = { .offset = 0x11, .value = 0xa0, }, - [48] = { .offset = 0x12, .value = 0x02, }, - [49] = { .offset = 0x20, .value = 0x00, }, - [50] = { .offset = 0x22, .value = 0x00, }, - [51] = { .offset = 0x23, .value = 0x00, }, - [52] = { .offset = 0x24, .value = 0x00, }, - [53] = { .offset = 0x25, .value = 0x00, }, - [54] = { .offset = 0x8c, .value = 0x10, }, - [55] = { .offset = 0x8d, .value = 0x02, }, - [56] = { .offset = 0x8e, .value = 0x10, }, - [57] = { .offset = 0x8f, .value = 0x00, }, - [58] = { .offset = 0x90, .value = 0xff, }, - [59] = { .offset = 0x91, .value = 0x07, }, - [60] = { .offset = 0x92, .value = 0xa0, }, - [61] = { .offset = 0x93, .value = 0x02, }, - [62] = { .offset = 0xa5, .value = 0x00, }, - [63] = { .offset = 0xa6, .value = 0x00, }, - [64] = { .offset = 0xa7, .value = 0x00, }, - [65] = { .offset = 0xa8, .value = 0x00, }, - [66] = { .offset = 0xa9, .value = 0x04, }, - [67] = { .offset = 0xaa, .value = 0x70, }, - [68] = { .offset = 0xab, .value = 0x4f, }, - [69] = { .offset = 0xac, .value = 0x00, }, - [70] = { .offset = 0xa4, .value = 0x84, }, - [71] = { .offset = 0x7e, .value = 0x18, }, - [72] = { .offset = 0x84, .value = 0x00, }, - [73] = { .offset = 0x85, .value = 0x00, }, - [74] = { .offset = 0x86, .value = 0x00, }, - [75] = { .offset = 0x87, .value = 0x00, }, - [76] = { .offset = 0x88, .value = 0x00, }, - [77] = { .offset = 0x89, .value = 0x00, }, - [78] = { .offset = 0x8a, .value = 0x00, }, - [79] = { .offset = 0x8b, .value = 0x00, }, - [80] = { .offset = 0x26, .value = 0x00, }, - [81] = { .offset = 0x27, .value = 0x00, }, - [82] = { .offset = 0xad, .value = 0x00, }, - [83] = { .offset = 0x08, .value = 0x30, }, /* 0x31 */ - [84] = { .offset = 0x41, .value = 0x00, }, - [85] = { .offset = 0xc0, .value = 0x05, }, + .sync = NS2501_C0_ENABLE | NS2501_C0_VSYNC, + .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD, + .syncb = 0x32, + .dither = 0x0f, + .pll_a = 17, + .pll_b = 852, + .hstart = 144, + .hstop = 783, + .vstart = 22, + .vstop = 514, + .vsync = 2047, /* actually, ignored with this config */ + .vtotal = 1341, + .hpos = 0, + .vpos = 16, + .voffs = 36, + .hscale = 40960, + .vscale = 40960 }, [MODE_800x600] = { - [0] = { .offset = 0x0a, .value = 0x81, }, - [1] = { .offset = 0x18, .value = 0x07, }, - [2] = { .offset = 0x19, .value = 0x00, }, - [3] = { .offset = 0x1a, .value = 0x00, }, - [4] = { .offset = 0x1b, .value = 0x19, }, - [5] = { .offset = 0x1c, .value = 0x64, }, - [6] = { .offset = 0x1d, .value = 0x02, }, - [7] = { .offset = 0x1e, .value = 0x02, }, - [8] = { .offset = 0xf3, .value = 0x90, }, - [9] = { .offset = 0xf9, .value = 0x00, }, - [10] = { .offset = 0xc1, .value = 0xd7, }, - [11] = { .offset = 0xc2, .value = 0x00, }, - [12] = { .offset = 0xc3, .value = 0xf8, }, - [13] = { .offset = 0xc4, .value = 0x03, }, - [14] = { .offset = 0xc5, .value = 0x1a, }, - [15] = { .offset = 0xc6, .value = 0x00, }, - [16] = { .offset = 0xc7, .value = 0x73, }, - [17] = { .offset = 0xc8, .value = 0x02, }, - [18] = { .offset = 0xf4, .value = 0x00, }, - [19] = { .offset = 0x80, .value = 0x27, }, - [20] = { .offset = 0x81, .value = 0x03, }, - [21] = { .offset = 0x82, .value = 0x41, }, - [22] = { .offset = 0x83, .value = 0x05, }, - [23] = { .offset = 0x94, .value = 0x00, }, - [24] = { .offset = 0x95, .value = 0x00, }, - [25] = { .offset = 0x96, .value = 0x05, }, - [26] = { .offset = 0x97, .value = 0x00, }, - [27] = { .offset = 0x9a, .value = 0x88, }, - [28] = { .offset = 0x9b, .value = 0x00, }, - [29] = { .offset = 0x98, .value = 0x00, }, - [30] = { .offset = 0x99, .value = 0x00, }, - [31] = { .offset = 0xf7, .value = 0x88, }, - [32] = { .offset = 0xf8, .value = 0x06, }, - [33] = { .offset = 0x9c, .value = 0x23, }, - [34] = { .offset = 0x9d, .value = 0x00, }, - [35] = { .offset = 0x9e, .value = 0x25, }, - [36] = { .offset = 0x9f, .value = 0x03, }, - [37] = { .offset = 0xa0, .value = 0x28, }, - [38] = { .offset = 0xa1, .value = 0x01, }, - [39] = { .offset = 0xa2, .value = 0x28, }, - [40] = { .offset = 0xa3, .value = 0x05, }, - [41] = { .offset = 0xb6, .value = 0x09, }, - [42] = { .offset = 0xb8, .value = 0x30, }, - [43] = { .offset = 0xb9, .value = 0xc8, }, - [44] = { .offset = 0xba, .value = 0x00, }, - [45] = { .offset = 0xbb, .value = 0x20, }, - [46] = { .offset = 0x10, .value = 0x20, }, - [47] = { .offset = 0x11, .value = 0xc8, }, - [48] = { .offset = 0x12, .value = 0x02, }, - [49] = { .offset = 0x20, .value = 0x00, }, - [50] = { .offset = 0x22, .value = 0x00, }, - [51] = { .offset = 0x23, .value = 0x00, }, - [52] = { .offset = 0x24, .value = 0x00, }, - [53] = { .offset = 0x25, .value = 0x00, }, - [54] = { .offset = 0x8c, .value = 0x10, }, - [55] = { .offset = 0x8d, .value = 0x02, }, - [56] = { .offset = 0x8e, .value = 0x04, }, - [57] = { .offset = 0x8f, .value = 0x00, }, - [58] = { .offset = 0x90, .value = 0xff, }, - [59] = { .offset = 0x91, .value = 0x07, }, - [60] = { .offset = 0x92, .value = 0xa0, }, - [61] = { .offset = 0x93, .value = 0x02, }, - [62] = { .offset = 0xa5, .value = 0x00, }, - [63] = { .offset = 0xa6, .value = 0x00, }, - [64] = { .offset = 0xa7, .value = 0x00, }, - [65] = { .offset = 0xa8, .value = 0x00, }, - [66] = { .offset = 0xa9, .value = 0x83, }, - [67] = { .offset = 0xaa, .value = 0x40, }, - [68] = { .offset = 0xab, .value = 0x32, }, - [69] = { .offset = 0xac, .value = 0x00, }, - [70] = { .offset = 0xa4, .value = 0x80, }, - [71] = { .offset = 0x7e, .value = 0x18, }, - [72] = { .offset = 0x84, .value = 0x00, }, - [73] = { .offset = 0x85, .value = 0x00, }, - [74] = { .offset = 0x86, .value = 0x00, }, - [75] = { .offset = 0x87, .value = 0x00, }, - [76] = { .offset = 0x88, .value = 0x00, }, - [77] = { .offset = 0x89, .value = 0x00, }, - [78] = { .offset = 0x8a, .value = 0x00, }, - [79] = { .offset = 0x8b, .value = 0x00, }, - [80] = { .offset = 0x26, .value = 0x00, }, - [81] = { .offset = 0x27, .value = 0x00, }, - [82] = { .offset = 0xad, .value = 0x00, }, - [83] = { .offset = 0x08, .value = 0x30, }, /* 0x31 */ - [84] = { .offset = 0x41, .value = 0x00, }, - [85] = { .offset = 0xc0, .value = 0x07, }, + .sync = NS2501_C0_ENABLE | + NS2501_C0_HSYNC | NS2501_C0_VSYNC, + .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD, + .syncb = 0x00, + .dither = 0x0f, + .pll_a = 25, + .pll_b = 612, + .hstart = 215, + .hstop = 1016, + .vstart = 26, + .vstop = 627, + .vsync = 807, + .vtotal = 1341, + .hpos = 0, + .vpos = 4, + .voffs = 35, + .hscale = 51248, + .vscale = 51232 }, [MODE_1024x768] = { - [0] = { .offset = 0x0a, .value = 0x81, }, - [1] = { .offset = 0x18, .value = 0x07, }, - [2] = { .offset = 0x19, .value = 0x00, }, - [3] = { .offset = 0x1a, .value = 0x00, }, - [4] = { .offset = 0x1b, .value = 0x11, }, - [5] = { .offset = 0x1c, .value = 0x54, }, - [6] = { .offset = 0x1d, .value = 0x03, }, - [7] = { .offset = 0x1e, .value = 0x02, }, - [8] = { .offset = 0xf3, .value = 0x90, }, - [9] = { .offset = 0xf9, .value = 0x00, }, - [10] = { .offset = 0xc1, .value = 0x90, }, - [11] = { .offset = 0xc2, .value = 0x00, }, - [12] = { .offset = 0xc3, .value = 0x0f, }, - [13] = { .offset = 0xc4, .value = 0x03, }, - [14] = { .offset = 0xc5, .value = 0x16, }, - [15] = { .offset = 0xc6, .value = 0x00, }, - [16] = { .offset = 0xc7, .value = 0x02, }, - [17] = { .offset = 0xc8, .value = 0x02, }, - [18] = { .offset = 0xf4, .value = 0x00, }, - [19] = { .offset = 0x80, .value = 0xff, }, - [20] = { .offset = 0x81, .value = 0x07, }, - [21] = { .offset = 0x82, .value = 0x3d, }, - [22] = { .offset = 0x83, .value = 0x05, }, - [23] = { .offset = 0x94, .value = 0x00, }, - [24] = { .offset = 0x95, .value = 0x00, }, - [25] = { .offset = 0x96, .value = 0x05, }, - [26] = { .offset = 0x97, .value = 0x00, }, - [27] = { .offset = 0x9a, .value = 0x88, }, - [28] = { .offset = 0x9b, .value = 0x00, }, - [29] = { .offset = 0x98, .value = 0x00, }, - [30] = { .offset = 0x99, .value = 0x00, }, - [31] = { .offset = 0xf7, .value = 0x88, }, - [32] = { .offset = 0xf8, .value = 0x0a, }, - [33] = { .offset = 0x9c, .value = 0x24, }, - [34] = { .offset = 0x9d, .value = 0x00, }, - [35] = { .offset = 0x9e, .value = 0x25, }, - [36] = { .offset = 0x9f, .value = 0x03, }, - [37] = { .offset = 0xa0, .value = 0x28, }, - [38] = { .offset = 0xa1, .value = 0x01, }, - [39] = { .offset = 0xa2, .value = 0x28, }, - [40] = { .offset = 0xa3, .value = 0x05, }, - [41] = { .offset = 0xb6, .value = 0x09, }, - [42] = { .offset = 0xb8, .value = 0x00, }, - [43] = { .offset = 0xb9, .value = 0xa0, }, - [44] = { .offset = 0xba, .value = 0x00, }, - [45] = { .offset = 0xbb, .value = 0x20, }, - [46] = { .offset = 0x10, .value = 0x00, }, - [47] = { .offset = 0x11, .value = 0xa0, }, - [48] = { .offset = 0x12, .value = 0x02, }, - [49] = { .offset = 0x20, .value = 0x00, }, - [50] = { .offset = 0x22, .value = 0x00, }, - [51] = { .offset = 0x23, .value = 0x00, }, - [52] = { .offset = 0x24, .value = 0x00, }, - [53] = { .offset = 0x25, .value = 0x00, }, - [54] = { .offset = 0x8c, .value = 0x10, }, - [55] = { .offset = 0x8d, .value = 0x02, }, - [56] = { .offset = 0x8e, .value = 0x10, }, - [57] = { .offset = 0x8f, .value = 0x00, }, - [58] = { .offset = 0x90, .value = 0xff, }, - [59] = { .offset = 0x91, .value = 0x07, }, - [60] = { .offset = 0x92, .value = 0xa0, }, - [61] = { .offset = 0x93, .value = 0x02, }, - [62] = { .offset = 0xa5, .value = 0x00, }, - [63] = { .offset = 0xa6, .value = 0x00, }, - [64] = { .offset = 0xa7, .value = 0x00, }, - [65] = { .offset = 0xa8, .value = 0x00, }, - [66] = { .offset = 0xa9, .value = 0x04, }, - [67] = { .offset = 0xaa, .value = 0x70, }, - [68] = { .offset = 0xab, .value = 0x4f, }, - [69] = { .offset = 0xac, .value = 0x00, }, - [70] = { .offset = 0xa4, .value = 0x84, }, - [71] = { .offset = 0x7e, .value = 0x18, }, - [72] = { .offset = 0x84, .value = 0x00, }, - [73] = { .offset = 0x85, .value = 0x00, }, - [74] = { .offset = 0x86, .value = 0x00, }, - [75] = { .offset = 0x87, .value = 0x00, }, - [76] = { .offset = 0x88, .value = 0x00, }, - [77] = { .offset = 0x89, .value = 0x00, }, - [78] = { .offset = 0x8a, .value = 0x00, }, - [79] = { .offset = 0x8b, .value = 0x00, }, - [80] = { .offset = 0x26, .value = 0x00, }, - [81] = { .offset = 0x27, .value = 0x00, }, - [82] = { .offset = 0xad, .value = 0x00, }, - [83] = { .offset = 0x08, .value = 0x34, }, /* 0x35 */ - [84] = { .offset = 0x41, .value = 0x00, }, - [85] = { .offset = 0xc0, .value = 0x01, }, - }, + .sync = NS2501_C0_ENABLE | NS2501_C0_VSYNC, + .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD, + .syncb = 0x32, + .dither = 0x0f, + .pll_a = 11, + .pll_b = 1350, + .hstart = 276, + .hstop = 1299, + .vstart = 15, + .vstop = 1056, + .vsync = 2047, + .vtotal = 1341, + .hpos = 0, + .vpos = 7, + .voffs = 27, + .hscale = 65535, + .vscale = 65535 + } +}; + +/* + * Other configuration values left by the BIOS of the + * Fujitsu S6010 in the DVO control registers. Their + * value does not depend on the BIOS and their meaning + * is unknown. + */ + +static const struct ns2501_reg mode_agnostic_values[] = { + /* 08 is mode specific */ + [0] = { .offset = 0x0a, .value = 0x81, }, + /* 10,11 are part of the mode specific configuration */ + [1] = { .offset = 0x12, .value = 0x02, }, + [2] = { .offset = 0x18, .value = 0x07, }, + [3] = { .offset = 0x19, .value = 0x00, }, + [4] = { .offset = 0x1a, .value = 0x00, }, /* PLL?, ignored */ + /* 1b,1c,1d are part of the mode specific configuration */ + [5] = { .offset = 0x1e, .value = 0x02, }, + [6] = { .offset = 0x1f, .value = 0x40, }, + [7] = { .offset = 0x20, .value = 0x00, }, + [8] = { .offset = 0x21, .value = 0x00, }, + [9] = { .offset = 0x22, .value = 0x00, }, + [10] = { .offset = 0x23, .value = 0x00, }, + [11] = { .offset = 0x24, .value = 0x00, }, + [12] = { .offset = 0x25, .value = 0x00, }, + [13] = { .offset = 0x26, .value = 0x00, }, + [14] = { .offset = 0x27, .value = 0x00, }, + [15] = { .offset = 0x7e, .value = 0x18, }, + /* 80-84 are part of the mode-specific configuration */ + [16] = { .offset = 0x84, .value = 0x00, }, + [17] = { .offset = 0x85, .value = 0x00, }, + [18] = { .offset = 0x86, .value = 0x00, }, + [19] = { .offset = 0x87, .value = 0x00, }, + [20] = { .offset = 0x88, .value = 0x00, }, + [21] = { .offset = 0x89, .value = 0x00, }, + [22] = { .offset = 0x8a, .value = 0x00, }, + [23] = { .offset = 0x8b, .value = 0x00, }, + [24] = { .offset = 0x8c, .value = 0x10, }, + [25] = { .offset = 0x8d, .value = 0x02, }, + /* 8e,8f are part of the mode-specific configuration */ + [26] = { .offset = 0x90, .value = 0xff, }, + [27] = { .offset = 0x91, .value = 0x07, }, + [28] = { .offset = 0x92, .value = 0xa0, }, + [29] = { .offset = 0x93, .value = 0x02, }, + [30] = { .offset = 0x94, .value = 0x00, }, + [31] = { .offset = 0x95, .value = 0x00, }, + [32] = { .offset = 0x96, .value = 0x05, }, + [33] = { .offset = 0x97, .value = 0x00, }, + /* 98,99 are part of the mode-specific configuration */ + [34] = { .offset = 0x9a, .value = 0x88, }, + [35] = { .offset = 0x9b, .value = 0x00, }, + /* 9c,9d are part of the mode-specific configuration */ + [36] = { .offset = 0x9e, .value = 0x25, }, + [37] = { .offset = 0x9f, .value = 0x03, }, + [38] = { .offset = 0xa0, .value = 0x28, }, + [39] = { .offset = 0xa1, .value = 0x01, }, + [40] = { .offset = 0xa2, .value = 0x28, }, + [41] = { .offset = 0xa3, .value = 0x05, }, + /* register 0xa4 is mode specific, but 0x80..0x84 works always */ + [42] = { .offset = 0xa4, .value = 0x84, }, + [43] = { .offset = 0xa5, .value = 0x00, }, + [44] = { .offset = 0xa6, .value = 0x00, }, + [45] = { .offset = 0xa7, .value = 0x00, }, + [46] = { .offset = 0xa8, .value = 0x00, }, + /* 0xa9 to 0xab are mode specific, but have no visible effect */ + [47] = { .offset = 0xa9, .value = 0x04, }, + [48] = { .offset = 0xaa, .value = 0x70, }, + [49] = { .offset = 0xab, .value = 0x4f, }, + [50] = { .offset = 0xac, .value = 0x00, }, + [51] = { .offset = 0xad, .value = 0x00, }, + [52] = { .offset = 0xb6, .value = 0x09, }, + [53] = { .offset = 0xb7, .value = 0x03, }, + /* b8,b9 are part of the mode-specific configuration */ + [54] = { .offset = 0xba, .value = 0x00, }, + [55] = { .offset = 0xbb, .value = 0x20, }, + [56] = { .offset = 0xf3, .value = 0x90, }, + [57] = { .offset = 0xf4, .value = 0x00, }, + [58] = { .offset = 0xf7, .value = 0x88, }, + /* f8 is mode specific, but the value does not matter */ + [59] = { .offset = 0xf8, .value = 0x0a, }, + [60] = { .offset = 0xf9, .value = 0x00, } }; static const struct ns2501_reg regs_init[] = { @@ -350,24 +378,11 @@ static const struct ns2501_reg regs_init[] = { struct ns2501_priv { bool quiet; - const struct ns2501_reg *regs; + const struct ns2501_configuration *conf; }; #define NSPTR(d) ((NS2501Ptr)(d->DriverPrivate.ptr)) -/* - * For reasons unclear to me, the ns2501 at least on the Fujitsu/Siemens - * laptops does not react on the i2c bus unless - * both the PLL is running and the display is configured in its native - * resolution. - * This function forces the DVO on, and stores the registers it touches. - * Afterwards, registers are restored to regular values. - * - * This is pretty much a hack, though it works. - * Without that, ns2501_readb and ns2501_writeb fail - * when switching the resolution. - */ - /* ** Read a register from the ns2501. ** Returns true if successful, false otherwise. @@ -531,9 +546,10 @@ static enum drm_mode_status ns2501_mode_valid(struct intel_dvo_device *dvo, } static void ns2501_mode_set(struct intel_dvo_device *dvo, - struct drm_display_mode *mode, - struct drm_display_mode *adjusted_mode) + const struct drm_display_mode *mode, + const struct drm_display_mode *adjusted_mode) { + const struct ns2501_configuration *conf; struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv); int mode_idx, i; @@ -541,6 +557,36 @@ static void ns2501_mode_set(struct intel_dvo_device *dvo, ("set mode (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d).\n", mode->hdisplay, mode->htotal, mode->vdisplay, mode->vtotal); + DRM_DEBUG_KMS("Detailed requested mode settings are:\n" + "clock : %d kHz\n" + "hdisplay : %d\n" + "hblank start : %d\n" + "hblank end : %d\n" + "hsync start : %d\n" + "hsync end : %d\n" + "htotal : %d\n" + "hskew : %d\n" + "vdisplay : %d\n" + "vblank start : %d\n" + "hblank end : %d\n" + "vsync start : %d\n" + "vsync end : %d\n" + "vtotal : %d\n", + adjusted_mode->crtc_clock, + adjusted_mode->crtc_hdisplay, + adjusted_mode->crtc_hblank_start, + adjusted_mode->crtc_hblank_end, + adjusted_mode->crtc_hsync_start, + adjusted_mode->crtc_hsync_end, + adjusted_mode->crtc_htotal, + adjusted_mode->crtc_hskew, + adjusted_mode->crtc_vdisplay, + adjusted_mode->crtc_vblank_start, + adjusted_mode->crtc_vblank_end, + adjusted_mode->crtc_vsync_start, + adjusted_mode->crtc_vsync_end, + adjusted_mode->crtc_vtotal); + if (mode->hdisplay == 640 && mode->vdisplay == 480) mode_idx = MODE_640x480; else if (mode->hdisplay == 800 && mode->vdisplay == 600) @@ -554,10 +600,44 @@ static void ns2501_mode_set(struct intel_dvo_device *dvo, for (i = 0; i < ARRAY_SIZE(regs_init); i++) ns2501_writeb(dvo, regs_init[i].offset, regs_init[i].value); - ns->regs = regs_1024x768[mode_idx]; - - for (i = 0; i < 84; i++) - ns2501_writeb(dvo, ns->regs[i].offset, ns->regs[i].value); + /* Write the mode-agnostic values */ + for (i = 0; i < ARRAY_SIZE(mode_agnostic_values); i++) + ns2501_writeb(dvo, mode_agnostic_values[i].offset, + mode_agnostic_values[i].value); + + /* Write now the mode-specific configuration */ + conf = ns2501_modes + mode_idx; + ns->conf = conf; + + ns2501_writeb(dvo, NS2501_REG8, conf->conf); + ns2501_writeb(dvo, NS2501_REG1B, conf->pll_a); + ns2501_writeb(dvo, NS2501_REG1C, conf->pll_b & 0xff); + ns2501_writeb(dvo, NS2501_REG1D, conf->pll_b >> 8); + ns2501_writeb(dvo, NS2501_REGC1, conf->hstart & 0xff); + ns2501_writeb(dvo, NS2501_REGC2, conf->hstart >> 8); + ns2501_writeb(dvo, NS2501_REGC3, conf->hstop & 0xff); + ns2501_writeb(dvo, NS2501_REGC4, conf->hstop >> 8); + ns2501_writeb(dvo, NS2501_REGC5, conf->vstart & 0xff); + ns2501_writeb(dvo, NS2501_REGC6, conf->vstart >> 8); + ns2501_writeb(dvo, NS2501_REGC7, conf->vstop & 0xff); + ns2501_writeb(dvo, NS2501_REGC8, conf->vstop >> 8); + ns2501_writeb(dvo, NS2501_REG80, conf->vsync & 0xff); + ns2501_writeb(dvo, NS2501_REG81, conf->vsync >> 8); + ns2501_writeb(dvo, NS2501_REG82, conf->vtotal & 0xff); + ns2501_writeb(dvo, NS2501_REG83, conf->vtotal >> 8); + ns2501_writeb(dvo, NS2501_REG98, conf->hpos & 0xff); + ns2501_writeb(dvo, NS2501_REG99, conf->hpos >> 8); + ns2501_writeb(dvo, NS2501_REG8E, conf->vpos & 0xff); + ns2501_writeb(dvo, NS2501_REG8F, conf->vpos >> 8); + ns2501_writeb(dvo, NS2501_REG9C, conf->voffs & 0xff); + ns2501_writeb(dvo, NS2501_REG9D, conf->voffs >> 8); + ns2501_writeb(dvo, NS2501_REGB8, conf->hscale & 0xff); + ns2501_writeb(dvo, NS2501_REGB9, conf->hscale >> 8); + ns2501_writeb(dvo, NS2501_REG10, conf->vscale & 0xff); + ns2501_writeb(dvo, NS2501_REG11, conf->vscale >> 8); + ns2501_writeb(dvo, NS2501_REGF9, conf->dither); + ns2501_writeb(dvo, NS2501_REG41, conf->syncb); + ns2501_writeb(dvo, NS2501_REGC0, conf->sync); } /* set the NS2501 power state */ @@ -579,34 +659,32 @@ static void ns2501_dpms(struct intel_dvo_device *dvo, bool enable) DRM_DEBUG_KMS("Trying set the dpms of the DVO to %i\n", enable); if (enable) { - if (WARN_ON(ns->regs[83].offset != 0x08 || - ns->regs[84].offset != 0x41 || - ns->regs[85].offset != 0xc0)) - return; - - ns2501_writeb(dvo, 0xc0, ns->regs[85].value | 0x08); + ns2501_writeb(dvo, NS2501_REGC0, ns->conf->sync | 0x08); - ns2501_writeb(dvo, 0x41, ns->regs[84].value); + ns2501_writeb(dvo, NS2501_REG41, ns->conf->syncb); - ns2501_writeb(dvo, 0x34, 0x01); + ns2501_writeb(dvo, NS2501_REG34, NS2501_34_ENABLE_OUTPUT); msleep(15); - ns2501_writeb(dvo, 0x08, 0x35); - if (!(ns->regs[83].value & NS2501_8_BPAS)) - ns2501_writeb(dvo, 0x08, 0x31); + ns2501_writeb(dvo, NS2501_REG8, + ns->conf->conf | NS2501_8_BPAS); + if (!(ns->conf->conf & NS2501_8_BPAS)) + ns2501_writeb(dvo, NS2501_REG8, ns->conf->conf); msleep(200); - ns2501_writeb(dvo, 0x34, 0x03); + ns2501_writeb(dvo, NS2501_REG34, + NS2501_34_ENABLE_OUTPUT | NS2501_34_ENABLE_BACKLIGHT); - ns2501_writeb(dvo, 0xc0, ns->regs[85].value); + ns2501_writeb(dvo, NS2501_REGC0, ns->conf->sync); } else { - ns2501_writeb(dvo, 0x34, 0x01); + ns2501_writeb(dvo, NS2501_REG34, NS2501_34_ENABLE_OUTPUT); msleep(200); - ns2501_writeb(dvo, 0x08, 0x34); + ns2501_writeb(dvo, NS2501_REG8, NS2501_8_VEN | NS2501_8_HEN | + NS2501_8_BPAS); msleep(15); - ns2501_writeb(dvo, 0x34, 0x00); + ns2501_writeb(dvo, NS2501_REG34, 0x00); } } -- cgit 1.2.3-korg