From 9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00 Mon Sep 17 00:00:00 2001 From: Yunhong Jiang Date: Tue, 4 Aug 2015 12:17:53 -0700 Subject: Add the rt linux 4.1.3-rt3 as base Import the rt linux 4.1.3-rt3 as OPNFV kvm base. It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and the base is: commit 0917f823c59692d751951bf5ea699a2d1e2f26a2 Author: Sebastian Andrzej Siewior Date: Sat Jul 25 12:13:34 2015 +0200 Prepare v4.1.3-rt3 Signed-off-by: Sebastian Andrzej Siewior We lose all the git history this way and it's not good. We should apply another opnfv project repo in future. Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423 Signed-off-by: Yunhong Jiang --- .../devicetree/bindings/gpio/brcm,kona-gpio.txt | 52 ++++++++++++++++++++++ 1 file changed, 52 insertions(+) create mode 100644 kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt (limited to 'kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt') diff --git a/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt new file mode 100644 index 000000000..4a63bc96b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt @@ -0,0 +1,52 @@ +Broadcom Kona Family GPIO +========================= + +This GPIO driver is used in the following Broadcom SoCs: + BCM11130, BCM11140, BCM11351, BCM28145, BCM28155 + +The Broadcom GPIO Controller IP can be configured prior to synthesis to +support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The +GPIO controller only supports edge, not level, triggering of interrupts. + +Required properties +------------------- + +- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends on the + number of GPIO banks on the SoC. The interrupts must be ordered by bank, + starting with bank 0. There is always a 1:1 mapping between banks and + IRQs. +- #gpio-cells: Should be <2>. The first cell is the pin number, the second + cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) + See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The + second cell is used to specify flags. The following subset of flags is + supported: + - trigger type (bits[1:0]): + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 3 = low-to-high or high-to-low edge triggered + Valid values are 1, 2, 3 + See also .../devicetree/bindings/interrupt-controller/interrupts.txt. +- gpio-controller: Marks the device node as a GPIO controller. +- interrupt-controller: Marks the device node as an interrupt controller. + +Example: + gpio: gpio@35003000 { + compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio"; + reg = <0x35003000 0x800>; + interrupts = + ; + #gpio-cells = <2>; + #interrupt-cells = <2>; + gpio-controller; + interrupt-controller; + }; -- cgit 1.2.3-korg