# This file defines the deployment for the MAAS environment which is to be # deployed and automated. demo-maas: maas: # Defines the general setup for the MAAS environment, including the # username and password for the host as well as the MAAS server. user: ubuntu password: ubuntu # Contains the virtual machine parameters for creating the MAAS virtual # server. Here you can configure the name of the virsh domain, the # parameters for how the network is attached. name: opnfv-maas-att interfaces: ['bridge=brAdm,model=virtio'] memory: 4096 vcpus: 2 arch: amd64 pool: default disk_size: 160G # Apt http proxy setting(s) apt_http_proxy: apt_sources: - ppa:maas/next - ppa:juju/stable # Virsh power settings # Specifies the uri and keys to use for virsh power control of the # juju virtual machine. If the uri is omitted, the value for the # --remote is used. If no power settings are desired, then do not # supply the virsh block. virsh: rsa_priv_key: /home/ubuntu/.ssh/id_rsa rsa_pub_key: /home/ubuntu/.ssh/id_rsa.pub uri: qemu+ssh://ubuntu@192.168.10.2/system # Defines the IP Address that the configuration script will use to # to access the MAAS controller via SSH. ip_address: 192.168.10.3 # This section allows the user to set a series of options on the # MAAS server itself. The list of config options can be found in # the upstream MAAS documentation: # - http://maas.ubuntu.com/docs/api.html#maas-server settings: main_archive: http://us.archive.ubuntu.com/ubuntu upstream_dns: 8.8.8.8 maas_name: attvirpod1 # kernel_opts: "console=tty0 console=ttyS1,115200n8" # ntp_server: ntp.ubuntu.com # This section is used to define the networking parameters for when # the node first comes up. It is fed into the meta-data cloud-init # configuration and is used to configure the networking piece of the # service. The contents of this section are written directly to the # /etc/network/interfaces file. # # Please note, this is slightly different than the # node-group-interfaces section below. This will configure the # machine's networking params, and the node-group-interfaces will # configure the maas node-group interfaces which is used for # controlling the dhcp, dns, etc. network_config: | auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.10.3 netmask 255.255.255.0 network 192.168.10.0 broadcast 192.168.10.255 gateway 192.168.10.1 dns-nameservers 8.8.8.8 127.0.0.1 # The node-group-interfaces section is used to configure the MAAS # network interfaces. Basic configuration is supported, such as which # device should be bound, the range of IP addresses, etc. # Note: this may contain the special identifiers: # ${maas_net} - the first 3 octets of the ipv4 address # ${maas_ip} - the ip address of the MAAS controller node_group_ifaces: - device: eth0 ip: 192.168.10.3 subnet_mask: 255.255.255.0 broadcast_ip: 192.168.10.255 router_ip: 192.168.10.1 static_range: low: 192.168.10.20 high: 192.168.10.100 dynamic_range: low: 192.168.10.101 high: 192.168.10.200 # Defines the physical nodes which are added to the MAAS cluster # controller upon startup of the node. nodes: - name: controller1 tags: control architecture: amd64/generic mac_addresses: - "" power: type: ether_wake address: - name: compute1 tags: compute architecture: amd64/generic mac_addresses: - "" power: type: ether_wake address: # Contains the virtual machine parameters for creating the Juju bootstrap # node virtual machine juju-bootstrap: name: bootstrap interfaces: ['bridge=brAdm,model=virtio'] memory: 4096 vcpus: 2 arch: amd64 pool: default disk_size: 120G