aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--docs/img/offloadingmodes.pngbin0 -> 23017 bytes
-rw-r--r--docs/img/softiron1.pngbin8447 -> 0 bytes
-rw-r--r--docs/installation-instruction.rst73
3 files changed, 51 insertions, 22 deletions
diff --git a/docs/img/offloadingmodes.png b/docs/img/offloadingmodes.png
new file mode 100644
index 00000000..5b3cb17b
--- /dev/null
+++ b/docs/img/offloadingmodes.png
Binary files differ
diff --git a/docs/img/softiron1.png b/docs/img/softiron1.png
deleted file mode 100644
index c420c412..00000000
--- a/docs/img/softiron1.png
+++ /dev/null
Binary files differ
diff --git a/docs/installation-instruction.rst b/docs/installation-instruction.rst
index 287e568f..49fd1699 100644
--- a/docs/installation-instruction.rst
+++ b/docs/installation-instruction.rst
@@ -58,7 +58,7 @@ Brahmaputra 3.0 release use the following command:
$ git clone https://gerrit.opnfv.org/gerrit/armband
-Check-out the Brahmaputra release tag to set the branch to the
+Check-out the Brahmaputra release tag to set the HEAD to the
baseline required to replicate the Brahmaputra release:
.. code-block:: bash
@@ -223,7 +223,7 @@ Install Fuel master
#. In the "Network Setup" section - Configure DHCP/Static IP information for your FUEL node - For example, ETH0 is 10.20.0.2/24 for FUEL booting and ETH1 is DHCP/Static in your corporate/lab network (see figure below).
- - **Note**: ArmbandFuel@OPNFV requires internet connectivity during bootstrap
+ - **NOTE**: ArmbandFuel@OPNFV requires internet connectivity during bootstrap
image building, due to missing arm64 (AArch64) packages in the partial
local Ubuntu mirror (consequence of ports.ubuntu.com mirror architecture).
@@ -309,25 +309,6 @@ scheme so that the FUEL Master can pick them up for control.
.. figure:: img/nodes.png
-Target specific configuration
------------------------------
-
-#. AMD Softiron
-
- For these targets, "rx-vlan-filter" offloading has to be turned off on the interface destined for OpenStack traffic (not the interface used for PXE boot).
- For now this setting cannot be toggled from Fuel GUI, so it has to be done form the console.
-
- - From Fuel master console identify target nodes admin IPs (see figure below).
-
- .. figure:: img/fuelconsole1.png
-
- - SSH into each of the target nodes and disable rx-vlan-filter on the physical interface allocated for OpenStack traffic (see figure below).
-
- .. figure:: img/softiron1.png
-
- - Repeat the step above for all AMD Softiron nodes in the POD.
-
-
Install additional Plugins/Features on the FUEL node
----------------------------------------------------
@@ -556,7 +537,6 @@ Allocate nodes to environment and assign functional roles
.. figure:: img/interfaceconf.png
-
OPTIONAL - UNTESTED - Set Local Mirror Repos
---------------------------------
@@ -589,6 +569,55 @@ that can be used for installation / deployment of openstack.
- Click <Save Settings> at the bottom to Save your changes
+Target specific configuration
+-----------------------------
+
+#. Set up targets for provisioning with non-default "Offloading Modes"
+
+ Some target nodes may require additional configuration after they are
+ PXE booted (bootstrapped); the most frequent changes are in defaults
+ for ethernet devices' "Offloading Modes" settings (e.g. some targets'
+ ethernet drivers may strip VLAN traffic by default).
+
+ If your target ethernet drivers have wrong "Offloading Modes" defaults,
+ in "Configure interfaces" page (described above), expand affected
+ interface's "Offloading Modes" and [un]check the relevant settings
+ (see figure below):
+
+ .. figure:: img/offloadingmodes.png
+
+#. Set up targets for "Verify Networks" with non-default "Offloading Modes"
+
+ **NOTE**: Check *Reference 15* for an updated and comprehensive list of
+ known issues and/or limitations, including "Offloading Modes" not being
+ applied during "Verify Networks" step.
+
+ Setting custom "Offloading Modes" in Fuel GUI will only apply those settings
+ during provisiong and **not** during "Verify Networks", so if your targets
+ need this change, you have to apply "Offloading Modes" settings by hand
+ to bootstrapped nodes.
+
+ **E.g.**: Our driver has "rx-vlan-filter" default "on" (expected "off") on
+ the Openstack interface(s) "eth1", preventing VLAN traffic from passing
+ during "Verify Networks".
+
+ - From Fuel master console identify target nodes admin IPs (see figure below):
+
+ .. code-block:: bash
+
+ $ fuel nodes
+
+ .. figure:: img/fuelconsole1.png
+
+ - SSH into each of the target nodes and disable "rx-vlan-filter" on the
+ affected physical interface(s) allocated for OpenStack traffic (eth1):
+
+ .. code-block:: bash
+
+ $ ssh root@10.20.0.6 ethtool -K eth1 rx-vlan-filter off
+
+ - Repeat the step above for all affected nodes/interfaces in the POD.
+
Verify Networks
---------------