summaryrefslogtreecommitdiffstats
path: root/docs/release/installation/virtualinstall.rst
blob: 61fc4be6f67d1fa68fb2cf125e662e67aa1a5284 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
Installation High-Level Overview - Virtual Deployment
=====================================================

The VM nodes deployment operates almost the same way as the bare metal
deployment with a few differences.  ``opnfv-deploy`` still deploys an
undercloud VM. In addition to the undercloud VM a collection of VMs
(3 control nodes + 2 compute for an HA deployment or 1 control node and 1
or more compute nodes for a non-HA Deployment) will be defined for the target
OPNFV deployment.  The part of the toolchain that executes IPMI power
instructions calls into libvirt instead of the IPMI interfaces on baremetal
servers to operate the power management.  These VMs are then provisioned with
the same disk images and configuration that baremetal would be. To Triple-O
these nodes look like they have just built and registered the same way as bare
metal nodes, the main difference is the use of a libvirt driver for the power
management.  Finally, the default network_settings file will deploy without
modification.  Customizations are welcome but not needed if a generic set of
network_settings are acceptable.

Installation Guide - Virtual Deployment
=======================================

This section goes step-by-step on how to correctly install and provision the
OPNFV target system to VM nodes.

Special Requirements for Virtual Deployments
--------------------------------------------

In scenarios where advanced performance options or features are used, such
as using huge pages with nova instances, DPDK, or iommu; it is required to
enabled nested KVM support.  This allows hardware extensions to be passed to
the overcloud VMs, which will allow the overcloud compute nodes to bring up
KVM guest nova instances, rather than QEMU.  This also provides a great
performance increase even in non-required scenarios and is recommended to be
enabled.

During deployment the Apex installer will detect if nested KVM is enabled,
and if not, it will attempt to enable it; while printing a warning message
if it cannot.  Check to make sure before deployment that Nested
Virtualization is enabled in BIOS, and that the output of ``cat
/sys/module/kvm_intel/parameters/nested`` returns "Y".  Also verify using
``lsmod`` that the kvm_intel module is loaded for x86_64 machines, and
kvm_amd is loaded for AMD64 machines.

Install Jumphost
----------------

Follow the instructions in the `Install Bare Metal Jumphost`_ section.

Running ``opnfv-deploy``
------------------------

You are now ready to deploy OPNFV!
``opnfv-deploy`` has virtual deployment capability that includes all of
the configuration necessary to deploy OPNFV with no modifications.

If no modifications are made to the included configurations the target
environment will deploy with the following architecture:

    - 1 undercloud VM

    - The option of 3 control and 2 or more compute VMs (HA Deploy / default)
      or 1 control and 1 or more compute VM (Non-HA deploy / pass -n)

    - 1-5 networks: provisioning, private tenant networking, external, storage
      and internal API. The API, storage and tenant networking networks can be
      collapsed onto the provisioning network.

Follow the steps below to execute:

1.  ``sudo opnfv-deploy -v [ --virtual-computes n ]
    [ --virtual-cpus n ] [ --virtual-ram n ]
    -n network_settings.yaml -d deploy_settings.yaml``

2.  It will take approximately 45 minutes to an hour to stand up undercloud,
    define the target virtual machines, configure the deployment and execute
    the deployment.  You will notice different outputs in your shell.

3.  When the deployment is complete the IP for the undercloud and a url for the
    OpenStack dashboard will be displayed

Verifying the Setup - VMs
-------------------------

To verify the set you can follow the instructions in the `Verifying the Setup`_
section.

.. _`Install Bare Metal Jumphost`: index.html#install-bare-metal-jumphost
.. _`Verifying the Setup`: index.html#verifying-the-setup