--- # Drydock BaremetalNode resources for a specific rack are stored in this file. # # NOTE: For new sites, you should complete the networks/physical/networks.yaml # file before working on this file. # # In this file, you should make the number of `drydock/BaremetalNode/v1` # resources equal the number of bare metal nodes you have, either by deleting # excess BaremetalNode definitions (if there are too many), or by copying and # pasting the last BaremetalNode in the file until you have the correct number # of baremetal nodes (if there are too few). # # Then in each file, address all additional NEWSITE-CHANGEME markers to update # the data in these files with the right values for your new site. # # *NOTE: The Genesis node is counted as one of the control plane nodes. Note # that the Genesis node does not appear on this bare metal list, because the # procedure to reprovision the Genesis host with MaaS has not yet been # implemented. Therefore there will be only three bare metal nodes in this file # with the 'masters' tag, as the genesis roles are assigned in a difference # place (profiles/genesis.yaml). # NOTE: The host profiles for the control plane are further divided into two # variants: primary and secondary. The only significance this has is that the # "primary" nodes are active Ceph nodes, whereas the "secondary" nodes are Ceph # standby nodes. For Ceph quorum, this means that the control plane split will # be 3 primary + 1 standby host profile, and the Genesis node counts toward one # of the 3 primary profiles. Other control plane services are not affected by # primary vs secondary designation. # # TODO: Include the hostname naming convention # # OVS-DPDK NOTE: Use the following host_profile for your nodes: # For ovs kernel: cp-intel-s2600wt or dp-intel-s2600wt # For ovs dpdk: cp-intel-s2600wt-dpdk or dp-intel-s2600wt-dpdk # schema: 'drydock/BaremetalNode/v1' metadata: schema: 'metadata/Document/v1' # NEWSITE-CHANGEME: Replace with the hostname of the first node in the rack, # after (excluding) genesis. name: pod18-node2 layeringDefinition: abstract: false layer: site storagePolicy: cleartext data: # NEWSITE-CHANGEME: The IPv4 address assigned to each logical network on this # node. In the reference Airship deployment, this is all logical Networks defined # in networks/physical/networks.yaml. IP addresses are manually assigned, by-hand. # (what could possibly go wrong!) The instructions differ for each logical # network, which are laid out below. addressing: # The iDrac/iLo IP of the node. It's important that this match up with the # node's hostname above, so that the rack number and node position encoded # in the hostname are accurate and matching the node that IPMI operations # will be performed against (for poweron, poweroff, PXE boot to wipe disk or # reconfigure identity, etc - very important to get right for these reasons). # These addresses should already be assigned to nodes racked and stacked in # the environment; these are not addresses which MaaS assigns. - network: oob address: 10.10.180.12 # The IP of the node on the PXE network. Refer to the static IP range # defined for the PXE network in networks/physical/networks.yaml. Begin allocating # IPs from this network, starting with the second IP (inclusive) from the # allocation range of this subnet (Genesis node will have the first IP). # Ex: If the start IP for the PXE "static" network is 10.23.20.11, then # genesis will have 10.23.20.11, this node will have 10.23.20.12, and # so on with incrementing IP addresses with each additional node. - network: dmz address: 10.10.180.22 # Genesis node gets first IP, all other nodes increment IPs from there # within the allocation range defined for the network in # networks/physical/networks.yaml - network: admin address: 10.10.181.22 # Genesis node gets first IP, all other nodes increment IPs from there # within the allocation range defined for the network in # networks/physical/networks.yaml - network: private address: 10.10.182.22 # Genesis node gets first IP, all other nodes increment IPs from there # within the allocation range defined for the network in # networks/physical/networks.yaml - network: storage address: 10.10.183.22 # Genesis node gets first IP, all other nodes increment IPs from there # within the allocation range defined for the network in # networks/physical/networks.yaml - network: management address: 10.10.184.22 # NEWSITE-CHANGEME: Set the host profile for the node. # Note that there are different host profiles depending if this is a control # plane vs data plane node, and different profiles that map to different types # hardware. Control plane host profiles are further broken down into "primary" # and "secondary" profiles (refer to the Notes section at the top of this doc). # Select the host profile that matches up to your type of # hardware and function. E.g., the r720 here refers to Dell R720 hardware, the # 'cp' refers to a control plane profile, and the "primary" means it will be # an active member in the ceph quorum. Refer to profiles/host/ for the list # of available host profiles specific to this site (otherwise, you may find # a general set of host profiles at the "type" or "global" layers/folders. # If you have hardware that is not on this list of profiles, you may need to # create a new host profile for that hardware. # Regarding control plane vs other data plane profiles, refer to the notes at # the beginning of this file. There should be one control plane node per rack, # including Genesis. Note Genesis won't actually be listed in this file as a # BaremetalNode, but the rest are. # This is the second "primary" control plane node after Genesis. host_profile: cp-intel-s2600wt-dpdk metadata: tags: # NEWSITE-CHANGEME: See previous comment. Apply 'masters' tag for control # plane node, and 'workers' tag for data plane hosts. - 'masters' # NEWSITE-CHANGEME: Refer to site engineering package or other supporting # documentation for the specific rack name. This should be a rack name that # is meaningful to data center personnel (i.e. a rack they could locate if # you gave them this rack designation). rack: pod18-rack ... --- schema: 'drydock/BaremetalNode/v1' metadata: schema: 'metadata/Document/v1' # NEWSITE-CHANGEME: The next node's hostname name: pod18-node3 layeringDefinition: abstract: false layer: site storagePolicy: cleartext data: # NEWSITE-CHANGEME: The next node's IPv4 addressing addressing: - network: oob address: 10.10.180.13 - network: dmz address: 10.10.180.23 - network: admin address: 10.10.181.23 - network: private address: 10.10.182.23 - network: storage address: 10.10.183.23 - network: management address: 10.10.184.23 # NEWSITE-CHANGEME: The next node's host profile # This is the third "primary" control plane profile after genesis host_profile: cp-intel-s2600wt-dpdk metadata: # NEWSITE-CHANGEME: The next node's rack designation rack: pod18-rack # NEWSITE-CHANGEME: The next node's role desigatnion tags: - 'masters' ... --- schema: 'drydock/BaremetalNode/v1' metadata: schema: 'metadata/Document/v1' # NEWSITE-CHANGEME: The next node's hostname name: pod18-node4 layeringDefinition: abstract: false layer: site storagePolicy: cleartext data: # NEWSITE-CHANGEME: The next node's IPv4 addressing addressing: - network: oob address: 10.10.180.14 - network: dmz address: 10.10.180.24 - network: admin address: 10.10.181.24 - network: private address: 10.10.182.24 - network: storage address: 10.10.183.24 - network: management address: 10.10.184.24 # NEWSITE-CHANGEME: The next node's host profile # This is the one and only appearance of the "secondary" control plane profile host_profile: dp-intel-s2600wt-dpdk metadata: # NEWSITE-CHANGEME: The next node's rack designation rack: pod18-rack # NEWSITE-CHANGEME: The next node's role desigatnion tags: - 'workers' ... --- schema: 'drydock/BaremetalNode/v1' metadata: schema: 'metadata/Document/v1' # NEWSITE-CHANGEME: The next node's hostname name: pod18-node5 layeringDefinition: abstract: false layer: site storagePolicy: cleartext data: # NEWSITE-CHANGEME: The next node's IPv4 addressing addressing: - network: oob address: 10.10.180.15 - network: dmz address: 10.10.180.25 - network: admin address: 10.10.181.25 - network: private address: 10.10.182.25 - network: storage address: 10.10.183.25 - network: management address: 10.10.184.25 # NEWSITE-CHANGEME: The next node's host profile host_profile: dp-intel-s2600wt-dpdk metadata: # NEWSITE-CHANGEME: The next node's rack designation rack: pod18-rack # NEWSITE-CHANGEME: The next node's role desigatnion tags: - 'workers' ...